Machine Operator Data Collector
Resume:
Richard Caranay Dollaga
PROFESSIONAL SUMMARY:
Proficient with electronic assemblies.
Worked on optical transceiver.
Experienced in handling calibration equipment, power tools, air-pressured screw driver, bolt meter, pliers, wire cutters.
Responsible for testing server for Google products.
PROFESSIONAL EXPERIENCE:
Cpacket network, Milpitas Blvd, CA 04/22 - Present
Assembler / Testing Technician
Responsible for testing the data collector for the customer record
Installation of a new currency volt
Checking that all components, fuses are running
Checking the high voltage / test meter for grounding
Identify quality issue and support the engineer team to root cause and counter-measure
Complete instrument and orders on time
Put hard kit in the unit and packaging products
Unigen, Fremont, CA 09/16 - 01/20
Testing Tech
Responsible for testing server for Google products.
Disassembles power supply after testing.
Worked on optical transceiver.
Checks fuse voltage and ground hipat test.
Packaging products.
Tesla Motors, Fremont 06/14 - 07/15
Tech Assembly
Responsible for cross training for the production line.
Loaded white and black washers to the battery modules and final inspection of the batteries.
Handled calibration equipment, power tools, air-pressured screw driver, bolt meter, pliers, wire cutters.
Vander-Bend, Sunnyvale 10/12 - 04/14
Assembler/ Test tech
Responsible for assembling for the JBox on the servers.
Attached ground cables and ground bars.
Screwed components to the chassis.
Put hard kits in the JBox.
Final inspection for QA.
Brocade Communications Systems, San Jose 01/12 - 09/13
Worked by contracts as a Test Operator, Assembler, and Receiving/Incoming Inspector, Machine Operator, Material Handler and Test Configuration Operator.
Microsoft Corporation, Sunnyvale 01/11 - 01/12
Tested and configured computers
Served as Receiving/Incoming Inspector of products
2Wire, Inc., San Jose 02/10 - 01/11
Tested and configured electronic units
Arthrocare, San Jose 03/09 - 02/10
Assembled and tested medical devices
Thermo Fisher Scientific, San Jose 04/08 - 03/09
Production and machine operator worked in the clean room
Bayer Corporation, Berkeley 05/07 - 04/08
Assembled medical devices
HEMOSENSE, San Jose 03/06 - 04/07
Optical Assembly Technician
Manufactured a point of care device for home testing of Prothrombin time of blood.
Lamination, nip rolling on strips cards, inspection using microscope, optics rejecting bad fiber parts and gap measurement.
Amphenol, San Jose 02/06 - 01/07
Assembler Technician II
Manufactured chassis for the cue line (network) switchboard.
Utilized power tools, voltmeters, back plane, harness cabling, and fan trays.
Responsible for final test burn.
Bell Microproducts, San Jose 01/04 - 02/06
E/M Assembler
Worked on E/M assembly line, responsible for attaching memory cards, power supplies, cables, fans and monitors.
Performed LED and burn-in testing.
Responsible for cycle count packaging and inventory control all the way through shipment release. This includes pulling kits for assembly line and level units and bar codes scanning.
Johnson & Johnson, San Jose 11/02 - 01/04
Optical Assembler
Responsible for building filter gasket which are used for patients with breathing problems.
Used Electra polish solution to polish filter gaskets.
Used Mario acid hydrogen test equipment for bright testing image stent and VC-filter.
Inspected VC filters with the use of microscope optics looking for any unpolished excess material, contamination or discoloration.
Monitored and documented weight scale measurement, wail thickness, struts measurement and serial numbers.
Calibrated all test equipment by cleaning parts using alcohol warm and acetone.
Sun Microsystems, Menlo Park 05/01 - 10/02
Technician II
Responsible for assembling and testing network server cabinet.
Performed cable wiring set up for servers that will be installed inside racks or cabinets.
Performed troubleshooting and analysis of wire set up for servers.
Reflectivity Corp., Santa Clara 03/00 - 05/01
Technician
Disassembled microscopes optics assembly and changed fixtures plates for analysis of uniform die image.
Troubleshooting includes the use of a CCD monitor to inspect the die image, working the light source that will apply voltage that corresponds to the brightest image and measurement angle.
Worked under microscope on dips controlling program.
EDUCATION:
Business Management, Saint Louis University Baguio City, Philippines
Contact this candidate