Quality Inspector Order Selector
Resume:
Justin D. Winters
Tel: 219-***-****
***************@*****.***
OBJECTIVE
Seeking a position that will allow for the opportunity to utilize my production and operating experience as a contractor to secure a permanent position.
Education
• William A. Wirt High School-diploma
• Indiana University Northwest 2001-2003
• T.W.I.C Card Certified
Work Experience
Strom Engineering-Honeywell
May 2016-October 2016
Quality Inspector
•check quality produced from various areas that
contain carbon fiber
•Perform routine inspections on carbon fiber
production
•measure all defects according to speculations set by company requirements
Strom Engineering -ATI Allegheny Ludlum
August 2015-February 2016
5 Spiltter operator
•Direct the loading of coil
an operate controls to
place on saddle
•adjust feeding
guides,blades settings to
regulate specified depth
length or width of material
using hands or tools
Strom Engineering-Cytec Engineering
Aug 2014- February 2015
Greenville, TX.
Aerospace Delegated Quality Inspector
• Perform quality inspections of materials
• Consistently met expectations for incoming orders
• Monitored all carbon fiber rolls for any
imperfections
Afimac
May 2014-Aug.2014
Memphis, TN
Finish Food Inspector
• Perform weight and moisture checks on finish
products
• Operate and control cooking mills on cook deck
• Maintain floor operations and food safety
regulations
J R Gettier
March 2014
Lebanon, TN
Order Selector
• Drive and operate forklift stacking loads
• Select and pick orders according to invoice
• Operate electronic pallet jack
Strom Engineering –Bell Helicopter
July 2013-Sept. 2013
Arlington, TX
Aerospace Technician
• Composite bonder/layup for 747 wings (Fiberglass and Carbon fiber)
• Layup of small composite part fiberglass and carbon fiber material
• Used hand tools such as micrometers, calipers, and alignment gauges to coordinate measurements.
• Performed bonding of metallic and nonmetallic
materials to fabricate parts
• Fit core in panels where close tolerances are required for installation of details for completion of assembly Strom Engineering- Contractor for American Crystal Sugar Company
Aug 2011- July 2013
Crookston, MN
Sugar Boiler
• Ensures maximum pan yields of quality sugar meeting specifications while minimizing sugar losses
• Boils sugar efficiently and maximize sugar production
• Maintains sugar product quality standards
• Maintains safe pan floor operations
• Manages the sugar end juice flows, tank levels and pan boiling effectively
• Recognizes the impact sugar boiling has to other stations and operations within the factory
Insulation Fabricators
Mar.2009-Jun.2011
Hammond, IN
Machinist
• Cut and operate saw machine
• Drive and operate forklift stacking loads
• Supervise and control custodial services and inventory
• Perform aluminum and stainless steel shearing
andalterations
Madi- Contractor for Thomas Steel Strip
Aug 2008- Jan 2009
Warren, OH
Machine Operator
• Operated plating line, which produced plated nickel coils
• Performed routine maintenance on conveyor machines
• Operated various heavy equipment for transporting finished plated coils
Ameriforce- Contractor for Bayonne Shipyard
Mar 2008- July 2008
Bayonne, NJ
Outside Machinist
• Removed, replaced, repaired and aligned various types of valves and pump motors
• Assisted in engine alignment; removed, replaced and repaired forced draft blowers
• Removed, replaced and aligned fuel oil service pumps and electric motors
• Installed machinery and equipment according to layout plans, blueprints and other drawing in using hoists, lift trucks, hand and power tools
Venture Dynamics- Contractor for Northrop
Grumman
Aug. 2007- Feb.2008
Newport News, VA/ Portsmouth, VA
Outside Machinist
• Remove, replace, repair and align various types of valves
• Assist in engine alignment; remove, replace and repair forced draft blowers
• Remove, replace and align fuel oil service pumps
• Assist in overhauling of vessel elevators
• Install machinery and equipment according to layout plans, blueprints and other drawings in industrial establishment, using hoists, lift trucks, hand and power tools
• Read blueprints and schematic drawings
• Align machines and equipments, using hoists, jacks, hand tools, squares, rules, micrometers, and plumb bobs Stanrail Railroad Corporation
Sept.2003-Nov.2007
Gary, IN
Machinist
• Ran steel cutting machine
• Operated steel grinding machine for assembly line
• Ran steel press machines
• Handled materials to be placed on various machines
• Stacked finished product on pallets to sent out to vendors
• Handled material and steel up to and exceeding 60lbs
• Followed all OSHA safety guidelines and regulations
Contact this candidate