Medium Voltage Start Up
Resume:
Austin Simon
Houston, TX *****
***********.***@*****.***
Certifications and Licenses
Introduction to Management & Organizational Management Skills
NCCER# 8140747 (Instrumentation Technician, Industrial Electrician+, Instrument Tubing Fitter)
3M Cable Theory & Prep Medium Voltage 5-35KV (Stresscones)
70E Exp. 7/14/27
TDLR 4662280
OSHA
TWIC Card
Instrument and Elecreical Technician
Higdon Construction
September 2024 to January 2025
Terminate Instrument, Power, Controls (#16-250MCM)
Redline drawings
Trouble shoot Instrument and power
Assist client (Kinder Morgan & Solar Turbines) Commision & Start Up of Solar gas turbines
Electrical Technician
Triad Elecreic and Controls
December 2022 to September 2024
Build Stress Cones (medium voltage) #2-500MCM
HI POT Test Cables and Stresscones 20KV
Terminate #12-500MCM Power Distrubution, Motors, Controls
Commission & Start up
Electrician/Instrument Technician
Burrow Global
November 2020 to November 2022
Install instruments
Loop check
Check calibration
Site Supervisor
Contech Control Services
January 2018 to October 2020
Managed projects from $5,000 Expense projects to 10 Million dollar DCS upgrades
Managed simultaneously 3 I&E leads with 40 Electrical, Instrument and Fitter craftsman
Developed Cost Estimates for Client Proposals
Maintained Schedule and Cost on time and under budget
Successfully completed over $35,000,000.00 of capital projects with no recordable injuries Instrument Tech
MMR Group – Geismar, LA
November 2016 to January 2018
Calibrate, configure, and PM instruments using HART 475 & 875, Fluke 789, Fluke 727, Crystal Gauges
Assist Engineering locating instruments using P&ID for process upsets
Assist plant personnel with startup. Install 1/4in, 3/8in, 1/2in allow tubing for air and process systems
Redlines and developed loop drawings for the client Instrument Fitter and Instrument tech apprentice
Triad Electric & Controls (Motiva – Convent, LA)
September 2014 to November 2016
To November 2016 A Class Journeyman NCCER+/Tubing Fitter
Calibrate Instruments using HART and Honeywell communicator. Commissioned instrumentation/electrical systems, and tubing with plant QA/QC. Troubleshoot electrical and instrumentation systems. Installed 1/4in, 3/8in, 1in stainless steel, and allow tubing for air and process systems.
A Class Journeyman (NCCER +)
Merit Electric – Hopewell, TN
April 2013 to September 2014
Terminated motors, HOA (Hand Off Automatic), instruments, and lighting. Megged motors and wires
Temporary lighting, terminated valves and instruments, Installed conduit. Conduit layout, circuit diagram, single line diagram
Assisted with startup, loop checks, terminated in PLC (Programmable Logic Controls, DCS, and BMS (Burner Management System) cabinets, installed and terminated instruments and junction boxes, Megged wires, landed cables in MCC, made up motor leads, bump started motors/polarity test on motors. Electrical layout drawing, wiring diagram, single line diagram, location drawings.
A Class Journeyman
MMR Group – Bellingham, WA
May 2011 to April 2013
Install conduit, junction boxes, and lights and terminate lights and junction boxes. Electrical layout, circuit diagram, conduit layout drawings
Terminated PLC cabinets and instrument wire and performed loop checks
Energized panels, LOTO permits, LOTO procedures, schematic diagrams, control wiring terminated PLC (programmable logic controller) cabinet, trouble shooting, loop checks Education
Certificate of Completion in Organizational Management University of Houston
January 2018 to December 2020
NCCER Certificate of Completion in Instrumentation and Controls ABC Trade School – Baton Rouge, LA
January 2014 to December 2016
Skills
Communication skills (10+ years)
Oil & gas (10+ years)
Programmable Logic Controllers
Distributed Control Systems
Proposal Writing
Calibration
Electrical Experience
Blueprint Reading
Quality Assurance
Equipment Repair
Contact this candidate