Des Moines Equipment Maintenance

MICHAEL CLYDE MILLER

Des Moines, Iowa ***** 515-***-**** *******.**@*****.***

●Equipment Maintenance

●Effective Communication

●Palletizing

●Machine Operation

●Blueprint Reading

●OSHA Certified

●Carpentry

●Blueprinting

●Forklift Truck

WORK EXPERIENCE

Gleeson Constructors, South Dakota October 2018- December 2018

Construction Laborers

●Loaded, unloaded, or identified building materials, machinery, or tools, distributing them to the appropriate locations, according to project plans or specifications.

●Measured, marked, or recorded openings or distances to layout areas where construction work will be performed.

●Dug ditches or trenches, backfill excavations, or compact and level earth to grade specifications, using picks, shovels, pneumatic tampers, or rakes.

●Cleaned or prepared construction sites to eliminate possible hazards.

●Read plans, instructions, or specifications to determine work activities.

●Signaled equipment operators to facilitate alignment, movement, or adjustment of machinery, equipment, or materials.

●Lubricated, cleaned, or repaired machinery, equipment, or tools.

●Tended pumps, compressors, or generators to provide power for tools, machinery, or equipment or to heat or move materials, such as asphalt.

Welmans Fansteel, Creston IA February 2009 – January 2014

Foundry Mold

●Lifted upper mold sections from lower sections, and remove molded patterns.

●Cut spouts, runner holes, and sprue holes into molds.

●Moved and position workpieces, such as mold sections, patterns, and bottom boards, using cranes, or signal others to move workpieces.

●Formed and assembled slab cores around patterns, and position wire in mold sections to reinforce molds, using hand tools and glue.

●Sprinkled or sprayed parting agents onto patterns and mold sections to facilitate removal of patterns from molds.

●Sifted and packed sand into mold sections, core boxes, and pattern contours, using hand or pneumatic ramming tools.

●Positioned cores into lower sections of molds, and reassemble molds for pouring.

●Positioned patterns inside mold sections, and clamp sections together.

●Cleaned and smoothed molds, cores, and core boxes, and repair surface imperfections.

Self-Employed, Des Moines, IA January 1984 – January 2012

Carpenter

●Installed rough door and window frames, subflooring, fixtures, or temporary supports in structures undergoing construction or repair.

●Bore bolt holes in timber, masonry or concrete walls, using power drill.

●Anchored and braced forms and other structures in place, using nails, bolts, anchor rods, steel cables, planks, wedges, and timbers.

●Removed damaged or defective parts or sections of structures and repair or replace, using hand tools.

●Maintained records, document actions, and presented written progress reports.

●Installed structures or fixtures, such as windows, frames, floorings, trim, or hardware, using carpenters' hand or power tools.

●Erected scaffolding or ladders for assembling structures above ground level.

●Inspected ceiling or floor tile, wall coverings, siding, glass, or woodwork to detect broken or damaged structures.

●Verified trueness of structure, using plumb bob and level.

●Shaped or cut materials to specified measurements, using hand tools, machines, or power saws.

●Studied specifications in blueprints, sketches, or building plans to prepare project layout and determine dimensions and materials required.

●Measured and marked cutting lines on materials, using a ruler, pencil, chalk, and marking gauge.

●Followed established safety rules and regulations and maintain a safe and clean environment.

●Assembled and fastened materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue.

Haliburton, Casper, WY January 1981 – December 1985

Derrick Operators, Oil and Gas

●Steadied pipes during connection to or disconnection from drill or casing strings.

●Weighed clay, and mix with water and chemicals to make drilling mud, using portable mixers.

●Clamped holding fixtures on ends of hoisting cables.

●Prepared mud reports, and instruct crews about the handling of any chemical additives.

●Guided lengths of pipe into and out of elevators.

●Supervised crew members, and provide assistance in training them.

●Positioned and aligned derrick elements, using harnesses and platform climbing devices.

●Started pumps that circulate mud through drill pipes and boreholes to cool drill bits and flush out drill cuttings.

●Listened to mud pumps and check regularly for vibration and other problems to ensure that rig pumps and drilling mud systems are working properly.

●Set and bolted crown blocks to posts at tops of derricks.

●Inspected derricks for flaws, and clean and oil derricks to maintain proper working conditions.

EDUCATION

Creston, Creston Iowa

High School Diploma

Contact this candidate