Supply Chain North America

Joseph A. Dagosto

* ****** **.

Londonderry N.H. 03053

Phone# Home: (603) - 437-1026

Cell : (603) - 264-1101

EMAIL: *********@***.***

Work Experience:

**/ **** ** ******* **** Green Power : Andover MA

Expediting Specialist – Supply Chain

Support Solar and Wind Projects in North America Coordinating Wind and Solar component manufacturing.

Track and resolve issues with Major equipment Suppliers for Enel North America Wind and Solar projects.

Coordinate and disposition of Non-Conforming Hardware that occurs at Supplier Manufacturing and Construction sites.

Manage Second Party witness inspections of Various Wind and Solar equipment, including Wind Turbine Blades, Nacelles, Towers, Solar Panels, Inverters Main Power transformers.

Report Manufacturing progress of Suppliers to ensure timely delivery of components to site.

Review Supplier Manufacturing and Quality plans to ensure compliance to Enel standards.

01/ 2017 to 08/2017 Belcan Engineering: Hooksett, NH

Manufacturing Engineer at G.E. Aircraft Engines

Manufacturing Engineering Support for Integral Machined Inconel Compressor Blisks.

Support manufacturing process including NC Turning, NC Milling / Drilling, ECM and Shot Peen .

Coordinate disposition of Non-Conforming Hardware and submitting parts into the G.E. MRB system for Disposition .

Review of inspection reports including CMM and Unigraphics Data.

Investigate Root cause and corrective action for non-conforming hardware .Work with Manufacturing Engineers, N.C. Programmers, Certifying Agents to develop Repair procedures for non conforming parts.

Provide Process capability information in Mini-Tab to help determine corrective and preventive actions.

12/2013 to 01/ 2017 Cobham Antenna Systems: Exeter, NH

Supplier Quality Engineer

MRB / Nonconforming Material Engineering, disposition Supplier Material, Processes

NPI Review for purchased parts specification review, First Article requirements.

Provide Quality Engineering Support for Vendor Special Processes, including, Heat, Coatings / Plating’s, Machining,

Specify and review Purchase orders for Quality Requirements of purchased raw Material, special Processes, and tooling.

Review ECO's For Purchased Parts

Supplier Quality Ratings DPPM / Supplier Audits.

04/2012 to 11/2013 Magellan Aerospace: Haverhill, MA

Quality Engineer

MRB / Nonconforming Material Engineering, disposition of machined aerospace components for rework / repair.

Submittal of Concessions, Root Cause Corrective Action, for Rolls Royce, MTU, G.E., Honeywell Aircraft Engine Components.

Submit First Article Data and Special/Fixed Process Approvals for Rolls Royce U.S.A., G.E., MTU Aircraft Engine components.

DSQR, for MTU Aero Engines Components.

Quality Engineering Planning for Inspection of Machined Components, review GDT requirements, specifies and order gages and measuring equipment.

Provide Quality Engineering Support for Vendor Special Processes, including, Heat, Coatings / Plating’s, Machining, Splining, and F.P.I.

Specify and review Purchase orders for Quality Requirements of purchased raw Material, special Processes, and tooling.

Manage Monthly Scrap Reports; provide Root Cause and Preventive Actions.

11/2009 to 04/2012 Paradigm Precision: Malden Ma

Quality Engineer

Provide Quality Engineering support for Aerospace / Power System- Machined Part

Jet Engine Components. For G.E., Rolls Royce and Volvo.

Submit First Article Data and Vse Packages for G.E. components.

Disposition, Submit MRB and Repair Procedures for Non-Conforming hardware

Participate in Manufacturing /Quality N.P.I. for Machined Part Components.

Provide Quality Engineering Support for Vendor Special Processes, including, Heat TBC Coatings, Machining, Grinding, and F.P.I &X-Ray.

Liaison with Supplier Materials Raw Forgings & Castings for Aerospace Components.

06 /2006 to 9/2009 Insight Technology: Londonderry N.H.

Quality Assurance Engineer

Provided Quality Engineering support for the assembly and testing of Electro-Optical components and assemblies.

Review product test data results to ensure compliance to product specifications.

Perform product failure analysis to determine root cause and corrective actions.

Write and review inspection and process work instructions.

Perform a review of engineering and process changes to ensure product and process compliance.

Perform internal product and process self assessment audits for ISO9000 requirements.

Review product inspection data for lot acceptance with D.C.M.A personnel.

Collect and analyze Inspection and test data using Mini-Tab software to produce Pareto charts, Process Run charts, and process capability charts.

11/2005 to 5/2006 Raytheon Integrated Defense Systems: Andover Ma

Sr Quality Assurance Engineer

Provided Quality Engineering support for the fabricated and machined parts of the radar components group.

Participated in weekly Defect Prevention Team meetings to proactively correct process and quality issues on the manufacturing floor.

Performed Quality documentation and hardware review of Electro-Mechanical assemblies for presentation to the customer D.C.M.A. .

Dispositioned Non-Conforming hardware for Root-Cause and Corrective Action and presented MRB for review by the customer.

Initiated Engineering Design Change Request to resolve producability and quality issues for fabricated and machined parts.

Participated in weekly review of Quality metrics to determine performance trends and opportunities for improvement.

Performed review of The Technical Data Package to the Manufacturing Data Package for Quality compliance.

Performed Internal Self Assessment Audits for ISO/AS9100 requirements.

Completed Raytheon Six Sigma Training.

Completed Raytheon Statistical Quality Control Course.

03/98 to 11/2005 General Electric Aircraft Engines: Lynn MA, Manufacturing Quality Engineer

Support the manufacturing and quality requirements for components manufactured in house and farmed out for The Combuster Center of Excellence.

Initiate process improvements for manufacturing procedures, including machining, Tig-Welding, Spot and Seam Welding, EDM, Laser machining, and Assembly operations.

Investigate the cause and corrective action for non-conforming hardware and in-house audits of manufacturing procedures.

Performed internal process audits for ISO/AS9100 requirements.

Review manufacturing costs and quality reports and implement cost reduction projects.

Review manufacturing procedures with planning and special process personnel.

Provide quality planning for drawing characteristic accountability, source substantiation, and first article review.

Participated in lean manufacturing events to improve cycle time in the manufacturing cells.

Completed Six Sigma training and completed Greenbelt training project.

Participate in business review meetings with design engineering to improve product, quality,

Cost and delivery issues.

01/96 to 01/98 Wyman Gordon Investment Castings Tilton N.H. Manufacturing Engineer

Provide process plans, for the machining and assembly of Non ferrous investment castings for Aerospace and Commercial products.

Design machining, inspection, grinding, and straitening fixtures using Unigraphics V11.1, SDRC Ideas, & Autocad-Lt Cad/Cam systems.

Coordinate the in house machining and assembly operations with shop management & personnel.

Liaison outside servicing of machining, assembly, and tooling fabrication.

Review customer prints and cad models for productivity and drawing clarifications.

09/93 to 01/96: W.M. Berg Inc. East Rockaway N.Y Cost Estimator

Provide cost estimates for the manufacture and procurement of precision machine components including gears, timing pulleys, and linear motion devices

Review drawings for in house manufacturing capabilities and vendor operations.

Consult with engineering, manufacturing, and quality control personnel to review

requirements for tooling and inspection.

6/79 to 9/93: Grumman Aerospace Corporation Bethpage N.Y. Senior Manufacturing Methods Engineer

Provide manufacturing operation plans for the machining of Aircraft Structural Parts .Utilized the G.T.CAPP. System to create process plans to describe the machining operation sequences.

Analyze engineering drawings and computer graphic models (CAD-AM, CATIA) to develop the tooling and machining concepts. Provide tooling layouts and manufacturing sketches to describe the machining processes.

Numerical control programmer for 3 axes N.C. and C.N.C milling machines and 4 axis Sundstrand parts maker machine.

Developed Set-Up and Run Times for machining operations coordinate tooling and N.C. programming costs, and man-hours for proposals and in house standards.

Education: University Of Massachusetts at Lowell

Sept 1996- Bachelors Degree in Manufacturing Engineering Technology. Lowell Mass.

May 2006

Farmingdale State University of New York Farmingdale N.Y.

June 1979 A.A.S. Mechanical Technology.

Sewanhaka High School Floral Park N.Y.

June 1977 High School Regents Diploma

Mechanical Technology Program

UNIGRAPHICS V11.1

Oct 1996 Hybrid Modeling Fundamentals

Nov 1996 Mill 1 Applications

Contact this candidate