D’ANNAH CROSS

Contact

Overview

**** ****** ****** *** * 19136 · 267-***-****

adyxao@r.postjobfree.com

Self-Motivated Manufacturing Technician possessing Strong Work Ethic with Six Months/900 Hours Manufacturing and Automation Training. Experience with various Power Tools and Equipment and Able to Read Schematics. Training includes the following: Robotics, Computer Control Equipment, Quality Systems (Six Sigma), Hydraulic and Pneumatic Systems, Industrial and Residential Electronics, Designed and Built Custom PLCs. CNC Simulation Experience.

Education

Experience

MANUFACTURING AND AUTOMATIVE TECHNICIAN, Philadelphia technician training institute

AUGUST 2020

ADVANCED MANUFACTURING AND AUTOMATION CERTIFICATES

Lockout Tag Out Control Systems

Advance Control Systems

Basic Circuit Analysis

Basic Electronic Components

PLC and Control Panel Building

Devices & Components

Electro-Mechanical

Panel Building in Low Voltage

Basic PLC

RESIDENTIAL AND COMMERCIAL ELECTRICITY, Orleans technical college

SEPTEMBER 2015

Installed cables, conduits, tubing and switch devices. Draw Schematics, Blueprints and Technical Diagrams. Calculate Electrical Current Values. Single Pole, Double Pole, 3 Way Pole Switch Wiring, Junction Box.

CLEANROOM ASSEMBLER, ALIGN PRECISION

JULY 2023 – Present

Get Dress in full Cleanroom Gowns in the Gowning room, starting with a Hair Net, Hair Cover, Gloves, Remove Shoes, Put Cleanroom Gown on Fully Zipped, then Put Cleanroom Safety Shoes on and a Second set of Gloves. Cleaned out Pelican Shipment boxes with 99% ABV before starting given tasks for the day. Prepped N2 Bellows Leg by Installing the Bellow onto the N2 Leg with a Torque Driver. Prepped Elec Bellows Leg by Installing Bellow onto Elec Leg, and Prepped Vac Bellows Leg by Installing Vac Leg as well. Assembled Z Drives to be married to the Elec Leg I’d had to attach Elec Support Leg to Feed Through, Carefully and lightly marry the Z Drive to Support Leg. Remove Feed Through to Attach Air Lines to the Air Baring, Turn on Air Lines to lift safely, turn off while lifted install the u-clamp before putting into Pelican box. Take 6 pictures, Labels/Air Baring to make sure all serial numbers match up and bottom of Air Barings aren’t damaged/scratched. Once Leg is seated properly, remove fixture and Z Drive handle as well. Wind Down Coupling to bottom. Attach all Side Clamps to Leg. When Wrapping Motor Wrap Everything to the blue Bushing on cable, wrap bag around motor cable then zip tie securely. When seating Motor wires faced down, I kept the cables to the side hanging down Put on Feed Through Cover Lid (4) Screws. Round up cables, put in bag, zip tie cables with the plastic clamps the seat cables properly. Wrap Gear Box cables around put in small bag and zip tie as well. Modified Height Sheet Taped To Top. Mix Epoxy and apply to all (3) screws. Take (4) pictures label as well. Once Leg has been doubled checked for errors, fill out Iteration sheet; serial #, BID and pin height. Tape Inspection sheet to Feed Through Top Cover. Lastly take a photo of the entire leg to be vacuumed out and shipped. To assemble all the legs, I had to use multiple different tools, wrenches, Allen wrenches, torque wrenches, T-wrenches etc.

ASSEMBLER, Boekel - BioTron

MAY 2023 – JUNE 2023

Prepped Cell Station to Start Workorder for the Day. Gathered all Necessary Tools Pertaining to What Incubator Needs to be Assembled. Followed All Steps from Blueprints and Schematics to Properly Assemble and Test for Proper Functionality. Basic Tools Were Used, Screwdriver, Nut Driver, Power Tools, Pnuematic Tools as Well. After Properly Assembled, wiped out and Clean Down, Incubators Needs a HyPot Test for 30 minutes To See If It Heats Up at the Calibrated Temperature. Assuming All Test Past, Then I Would Gather All Acessories That Goes with the Incubator for Packaging and Shipping.

GENERAL ASSEMBLER, PeopleShare - EvenLite Inc

APRIL 2023 – APRIL 2023

Maintained Safety and Cleanliness at Certain Workstations while Working on Tasks, Along with Preparing Work Station(s) With the Proper Equipment at End of Every Shift for the Next Work Day or Continued Tasks from The Day Before. Studied, Followed and Deciphered Proper Directions on Schematics and Assembly Instructions. Paid Close Attention to Details When Assembling Parts, Motors and Subassemblies for Signs and Backup Lighting. Assembled Exit Signs and Backup Lighting Components with Fastening Parts, Washer Parts, Rivets and Other Various Parts Using Hand Tools, Air Tools and Power Tools, Crimpers, Splicers. Verified Components Were Assembled Efficiently and Correctly by Supervisor or Manager on the Floor.

DEVICE REPAIR TECHNICIAN, BIOMEME INC.

NOVEMBER 2021 – FEBRUARY 2023

Responsible For Identifying, Repairing, and Testing Complex Electro-Mechanical Faults. Use PC Aided Diagnostic Software to QC Devices. Practice All ESD Trainings Prior to Everyday Tasks. Thoroughly Pay Close Attention to Every Detail During Diagnostic Procedure. Properly Document, Collect and Store Necessary Paperwork and Data for All Devices. Soldered Capacitors, Resistors, Barrel Jacks along with numerous components on PCBs/SMBs When Necessary

LABORER, Premier Pointing LLC.

OCTOBER 2020 – SEPTEMBER 2021

Assist Team with Loading Company Vehicles with Bags of Sand, Cement, and Mortar Weighing Over 75lbs. Loaded All Necessary Tools Needed for the Job Such As; Shovels, Wheel-barrels, Scaffold, Mixer, Hand Tools and Power Tools. Practiced Safety Measures and Wore all Safety Equipment During Set Up and Break Down. Responsible for Brick Tinting, Tuck Pointing, Removing Mortar from Deteriorated Bricks. Washed Bricks with Muriatic Acid After Team Finished Pointing and Caulking. Unloaded Company Vehicles of Supplies That Were Used for the Day. Dumped Buckets of Debris at End of Shift

DEVICE REPAIR TECHNICIAN, Asurion

FEBRUARY 2020 – AUGUST 2020

Resolve Customers Issues by Troubleshooting and Repairing Electronic Devices as Needed. Assist Customers with Technical Support of Their Phones, Tablets, and Other Devices. Practice All Safety Procedures Before, During and After Device Repair. Reassure Customers That Device Is Functioning Properly.

Contact this candidate