Amr Ashor Mohamed Ali

*, ** *****`y st, El-Marg, Cairo, Egypt

011******** 012********

ady0rl@r.postjobfree.com

Personal INFORMATION

Date of birth 13/11/1989

Place of birth Cairo, Egypt.

Nationality Egyptian

Personal Status married

Military service status Served

Objective: Seeking a challenging position in a such great organization where my

interpersonal skills and technical knowledge can be applied and

further developed.

JOB EXPERIENCES

from sepetember 2016 to 2018

from february

2016 to till now

●Operating & maintenance Engineer for Asphalt mixing for 2years and half.

●Testing and commission engineer

●Testing and commission engineer at el sewedy company in quality control department

Tasks of quality control department

Test the medium voltage panels by

1.Visual inspection

2.Components specifications and their numbers

3.Wiring revision

4.Instruments like(saverkar 900, megger so on)

5.CT and VT ratio.

6.Last not least test for protection function like (over current, differential current, phase sequence, so on).

7.I do programming for many types of protection relay like (7sj,7sk,7sr11/12,micom).

Test the low voltage panels by

1.Visual insection

2.Components specifications and their numbers.

3.Wiring revision

4.CT and VT revision.

● Shift operator

1.Control room operator at new capital power plant 4800 mega watt ( four combined cycle 2 gas turbine with 2 hrsg and 1 steam turbine)

●Tasks of shift operator

1.Startup and shutdown for gas turbine.

2.Startup and shutdown for steam turbine.

3.Startupand shutdown for combined cycle power plant

4.Monitor alarm sequence display (ASD) at siemens T3000 HMI for combined cycle power plant and check the cause of the alarm.

5.Investigate at T3000 logic why the trips happen?

6.Investigate at T3000 logic the missing criteria during startup and shutdown for combined cycle

7.Walk down at site at the beginning of the shift

8.change over between( pumps, cooling fans, so on ) or for any system in operation at T3000 HMI

9.operate all systems like lube and lift oil system, hudraluic system and so on from standstill to be in operation.

10.do vaccum and seal steam at combiend cycle from standstill.

11.Do hrsg preservation by( netrogen or steam) if the combiend cycle stays outage for long time.

12.read PID of the combiend cycle very well.

13.i can extract what are the control and protection for all valves ? at T3000 HMI.

14.change over between standby gas compressor and in service gas compressor without any decreasing in gas pressure.

15.monitor all systems to keep light on.

16.purge by nitrogen for any important system like (gas preheat" EKT"after permit work done from maintenance team to make the system is save when my manager need it in operation.

EDUCATION AND

TRAINING

JULY 2012

university / Faculty

Graduation project

Cumulative grade

11sept. 2011-15 sept.2011

10 July 2010 – 25 Aug. 2010

July-Aug. / 2009

Jan-may /2017

June- july 2017

Bachelor of electrical power & machines engineering

Ain Shams University, Faculty of Engineering

Technical Specs, Bill Of Quantities for a Distribution System

( Grade : Excellent )

Very Good

Classic control training from ITC(Industrial Training Council )

Cairo North Power Station training program of Operation & Maintenance of (Steam – Gas-Combined cycle) power plant-

Turbines – Generators – Circuit breakers – transformers-..Etc.

Osman Ahmed Osman company ( Demerdash hospital )

Schneider visit ـــ Zafarana wind farm (one day for each )

Toshiba factory

North cairo training center

(gas turbine and hrsg and steam turbine mechanical component

gas, steam turbine and hrsg control and protection system

Gas turbine mechanical design .

Overview of electrical system design .

Turbine Logic revision

generator mechanical component

gas turbine and compressor blades design and manufacturing

stat up and shut down of combined cycle

training on poroscope use for investigating gas turbine and gas blades

Personal skills

Mother tongue(s)

arabic

Other language(s)

UNDERSTANDING

SPEAKING

WRITING

Listening

Reading

Spoken interaction

Spoken production

English

Very good

Excellent

Very good

Very good

Very good

Communication skills

Friendly, good listener, co-operative, self-motivated.

Organisational / managerial skills

Leadership (Graduation project leader and tasks organizer for

a team of 8 people)

good at working in a team Presentation skills

Negotiation Skills Problem solver

Strategic thinking

Computer skills

good command of Microsoft Office™ tools

project management program

Internet AutoCAD basics

Dailux Matlab basics

Other skills

Iam interesed in all electrical fields especially the newest fields, I love to read and search about it And I adore power electronics field and electrical power plant station systems .

Contact this candidate