Machine Operator Forklift
Resume:
Yusef Kindle
Racine, WI *****
***********@*****.***
Objective: An interesting position with a growing company
Diamond Precision Products Milwaukee, WI
CNC Machine Operator October 2022, February 2023
I ran and maintained 3 Bearing cap machines
Filled coolant and waylube in all 3 machines
Did daily checks to make sure parts was in tolerance
Sweeped and kept area clean
Ran plate Adapter for Catapiliar tractors
Used bore mics to check parts
Moved parts with Forklift when finished filling up bins
Kerry Inc. Sturtevant, WI
Forklift Operator/Selector April 2022, August 2022
I picked orders from a scanner
Lifted 50Lb. bags and stacked on a pallet
Cleaned and help sanitize the warehouse work area on weekends
Helped others when I completed my work assignment
Diamond Precision Products Milwaukee, WI
CNC Machine Operator August 2021, April 2022
I ran and maintained 3 Bearing cap machines
Filled coolant and waylube in all 3 machines
Did daily checks to make sure parts was in tolerance
Sweeped and kept area clean
Ran plate Adapter for Catapiliar tractors
Used bore mics to check parts
Moved parts with Forklift when finished filling up bins
Abbott Gurnee, ILL
PRODUCTION SPECIALIST November 2020, July 2021
I work on a line making covid test kits
3 people on a line, rotating stations every hour
We sanitize our hands when we get in the building, and then get our temperature checked by security guards
We wear gloves, face mask, eye protection, lab coats, and hair nets in the hub
Maintain daily quota 32,000 units per day
Put labels on covid cards with a label machine, put test strips in special location, place adhesive closure tape on finished covid kit, then put into a bag and sealed shut Inspect finished material, then pack into boxes then put onto a pallet
National Technologies INC. Oak Creek, WI
CNC Machine Operator May 2019, to October 2020
I come in and fill up coolant in the machine I’m scheduled to run, and clean out screens
Check inserts to make sure they still have some life on them
Run a part, then all measurements to make sure everything is in tolerance, if not I make offset to the correct tool
Maintain efficiency
Hold tight tolerances
Maintain clean work environment, sweep mop, wipe down machines
Deburr parts when needed
Kirsan Engineering Racine, WI
CNC Machine Operator / 2nd shift Supervisor August 2017 to April 2019
Maintain 2 to 3 Machines, Lathes, or Mills.
Clean screens, and dump chip baskets, and check Coolant levels before startup, if low I fill it up.
Put parts onto a CMM to verify the machines are running good.
Unload and reload the Machine, check the parts to verify that tools are still working properly.
Check parts to make sure they are in Tolerance with pin gauges, thread gauges, micrometer gauges, and calipers.
If parts aren’t in tolerance I make a offset, then recheck the parts to make sure the right offset was made properly.
Deburr any Flash on parts with grinding wheel, or a triblade.
Leave test pieces for the next shift, clean and sweep area, refill coolant for the next shift.
Monitor job progress on a day to day/ hour to hour
Reassign resources to meet production needs.
Maintain and Schedule Job card packets making sure instructions are followed and Monitor machines down time.
Reinforce company goals and objectives with Employees.
Strive for continuous improvements and cost reductions.
Follow company policies, procedures, and instructions.
Attend training to develop relevant knowledge and skills.
Monitor and report on activities and provide relevant management information.
Reinforce a clean and safe work area.
Wiscon Products Racine, WI
CNC Machine Operator August 2016 to August 2017
Operate CNC Mills, Lathes, Kitamura – Mycenter, Fellows – Gear Shaper, Tesker 320 – thread Roller and Yama Seiki – Fanuc.
Tag and set aside potential scrap parts.
Deburred Mill keyholes.
First piece inspection.
Regular quality inspections throughout the day.
Maintain proper coolant level.
Use small increment measuring devices.
Tool changes and off sets.
Run multi-spindle Index machines.
Use CMM too verity that running parts are good.
Check threads, run out and part fits on the spine gauge.
Measuring instruments used: CMM, Micrometers, Calipers, Height stands, Depth mics.
RustOleum Kenosha, WI
Forklift Driver May 15, to September 16
I used a voice recognition system to pick orders, through a Bluetooth headset
I used 2 pallets for separate assignments
Then used check sceens, and Upc numbers to pick orders through Bluetooth headset
When finished picking both orders, I would wrap them with plastic to keep products secure and ready for shipping, print out shipping labels for each pallets
Confirm each shipping labels with my paper work, label pallets
Take each pallet to correct shipping trailor with conformation of trailor serial number
Patrick Cudahy Cudahy, WI
Machine Operator / Forklift November 2012 to March 2015
Operated 3 horn machine to form finished product
Hung 70Ib.- 100Ib. sticks of meat onto a rack
Started on Walker Forklift for 3 months, then moved to Rider Forklift
Operated the sit down Forklift, when needed help in Shipping and
Receiving
Education: Gateway Technical College Racine, WI
GED anticipated 2023
References:
Contact this candidate