Michael Hebert

*** ****** ******, *** ******, CA 95046 / 408-***-**** / adwebq@r.postjobfree.com

QUALIFICATIONS, 39 YEARS OF EXPERIENCE

Electronic and Mechanical design, prototype, test, checkout, modify, DFM

AutoCAD 2D drawings, Solid Works 3D modeling, ANSYS space claim

Ability to use all hand tools and power tools also Mill, Lathe, Shear, Bandsaw

PC and MAC literate, Word, Excel, Power Point, Outlook, Pages, LabVIEW

Familiarity with Altium, expert with OrCAD, MENTOR and PSPICE

Design of flex PCB’s and cables

DVM, Logic Analyzer, Signal Generator, Oscilloscope, Wattmeter, DC Lab Power Supply, Etc

UNABLE TO WORK DUE TO ILLNESS, I had pneumonia in 07/2022, hospitalized and 6 months recovery.

EXPERIENCE

Electro-Mechanical Engineer, GENESYS, LLC, San Jose, CA 05/03/2021 – 05/07/2021

A company designing and prototyping a novel solar fuel cell technology platform.

Fabricated and machined system control panel, 4 switches, 4 pots and 4 dual binding posts.

Point to point wiring from the control panel to 4 high voltage power supplies.

Connected power cables from the HV power supplies to the solar panel output regulator.

Sr. Electro-Mechanical Engineer, dba JSC, Ltd., San Jose, CA 01/2019 – 12/2020

Tested and qualified 3 manufacturers of 400VDC 40 HP motors.

Assembled prototype pulse width modulated H bridge IGBT DC motor controller.

High voltage cable harness from battery pack to motor controller to DC motor.

Fabricated battery enclosure for 100 lithium-ion cells, 360VDC at 100AH.

Developed prototype battery charger circuit, 240VAC input and battery management unit.

OrCAD schematic capture, BOMs, PCB design and SolidWorks for mechanical assemblies.

Confidential client. 5 prototype vehicles.

Audio Design Engineer, dba JSC, Ltd., San Jose, CA 01/2018 – 06/2018

Design of three-piece class D stereo amplifier with detachable speakers.

Full range speakers, 8 ohms, 5 watts in wood cabinets with metal grill.

Rechargeable 12V lithium-ion battery and AC/DC switch mode power supply.

For use with iPODs, iPADs, MP3, CD players and cell phones.

OrCAD schematic capture, BOMs, PCB design and SolidWorks for mechanical assemblies.

Short-run production of 25 units.

Engineering Technician, LUMENETICS, Inc., Scotts Valley, CA 12/01/2017 – 12/31/2017

A company designing and manufacturing LED light fixtures.

Tested and troubleshot LED assemblies to the SMT component level under a microscope.

Soldered and unsoldered SMT components for PCB rework.

Tested LED light power supplies used semi-automatic test equipment.

Organized research & development components in bags with a written data base list.

Sr. Electro-Mechanical Engineer, dba JSC, Ltd., Santa Cruz, CA 08/2017 – 11/2017

Product design project, low-cost AC wattmeter and AC voltmeter equipment.

Analog circuit design and prototype unit, LCD digital panel meters, linear power supply.

OrCAD schematic capture, BOM, PCB design and AutoCAD for mechanical assemblies.

Short-run production of 10 units.

Electrical Cable Designer, VELO3D, Inc., Campbell, CA 06/01/2017 – 06/30/2017

A company designing and manufacturing metal 3D printers.

Drafting up to 3 cable designs per day, used ANSYS version of AutoCAD.

Sr. Electro-Mechanical Engineer, dba JSC, Ltd., Santa Cruz, CA 03/2017 – 05/2017

Product development project, PWM Bidirectional H bridge 24VDC motor controller.

Analog and digital circuit design, prototype assembly, 24VDC gearmotor, motor chassis.

OrCAD schematic capture, BOM, PCB design, COTS metal enclosure.

Short-run production of 15 units.

Power Supply Design Engineer, REVERSICA DESIGNS, Santa Cruz, CA 07/2016 – 10/2016

A company designing and manufacturing novel articulated rotating multi-media shelves.

Power analog circuit design, 120VAC input, 24VDC at 10A, forward converter, 500kHz.

Designed power supply to meet UL, CSA, TUV Rhineland, CE, EMC/EMI regulations.

Mentor schematic capture, BOM, PADS PCB design, AutoCAD for mechanical drawings.

Volunteer Delivery Driver, GRAY BEARS of CALIFORNIA, Santa Cruz, CA 01/2016 – 06/2016

Delivered produce to the elderly every Thursday morning.

Power Supply Engineer, AVOGY, Inc., San Jose, CA 09/2015 – 12/2015

A semiconductor company attempting to produce silicon GAN vertical transistors.

ZOLT AC/DC converter for USB charger, test and troubleshoot to SMT component level.

Supervised and mentored power supply technician.

Resolved burn-in rack issue by using relays that could handle the inrush current.

Solved power supply noise problem by placing a shield between the balun and transformer.

Inventoried all the power supply lab test equipment for calibration quote, chose lab that

could do the calibration onsite, saving both time and money approximately 30%.

Windows and Doors shop assistant, GREENHOUSES, etc., San Jose, CA 03/2014 – 07/2015

Watch store, answer phone calls, greet customers, when owner is out on business.

Compose and email Greenhouses, etc. introduction to potential customers.

Construction of window and door products display racks.

Worked 1 to 2 days every week.

Audio Design Engineer, dba JSC, Ltd., Santa Cruz, CA 10/2013 – 12/2013

Research and development of low EMI class D stereo amplifier 50 watts per channel.

Radio frequency PCB design, insulated MOSFET transistors, grounded heatsinks.

Shielded inductors, ferrite beads on MOSFET drain leads. Linear power supply.

OrCAD schematic capture, BOM, PCB design, AutoCAD for sheet metal enclosure.

Sr. Electro-Mechanical Engineer, dba JSC, Ltd., Santa Cruz, CA 06/2013 – 07/2013

Opto-electric sensor for refrigerator condenser coil ice detector.

Analog circuit design, breadboarded prototype components for testing.

4 – 20 milliamps current loop.

OrCAD schematic capture, BOM, PCB design. AutoCAD for enclosure design.

Sr. Electro-Mechanical Engineer, REVERSICA DESIGNS, Santa Cruz, CA 02/2013 – 04/2013

Dual axis X, Y stepper motor drivers.

Analog and digital circuit design, switch mode power supply, COTS metal enclosure.

2 stepper motor cables with sub D connectors both ends.

OrCAD schematic capture, BOM, PCB design, machined enclosure.

Power Supply Design Engineer, ECO SYSTEMS, Santa Cruz, CA 01/2012 – 12/2012

A company designing and installing commercial solar photovoltaic power systems.

Tested and qualified 2 manufacturers of 10kW DC/AC inverters that meet UL 708.

Used LabVIEW to control DC power sources, AC electronic load, to test DC/AC inverters.

Devised a power analog circuit to simulate a solar panel array.

Designed a precision DC power supply 0 – 10 V at 100 mA 1% for testing transducers.

Developed DC/DC buck regulator, 96VDC input, +5, +12, -12 output for PC computer.

Fabricated metrology transducers enclosure, wiring and I/O connectors.

Mentor Graphics schematic capture, BOM, PADS PCB, SolidWorks mechanical design.

Radio Frequency Engineer, TOYOTA INFO TECHNOLOGY CENTER, Mt. View, CA 08/2011 – 10/2011

Research and development center of northern California.

Testing and evaluating 5.95 Giga Hertz transmitter and 4 receivers.

Used 2 Prius cars for test, 1 car with transmitter and other car with 4 receivers.

12VDC PC computers in both cars, 1 for data transmission, 1 for data reception x4.

Radio testing was performed in residential settings at intersections.

Testing was also implemented in downtown San Jose.

The last test was on Hwy 101 with a semi tractor trailer in between the cars.

Electronics Design Engineer, E SYSTEMS TECHNOLOGY, Mountain View, CA 05/2011 – 07/2011

A company designing and producing equipment for the biotech industry.

Modification of existing analog and digital circuitry, changed resistors from 1% to 5%.

Increased power output of DC/DC buck converter from 3AMPS to 5AMPS.

5 sheet schematic drawing, I/O connectors & power, 4 piezoelectric motor controllers.

Handed off complete documentation package to contractor for PCB design.

Programmed 4 FPGA’s for each piezoelectric motor controller and SPI interface.

Shipping Container Fabricator, REVERSICA DESIGNS, Santa Cruz, CA 01/2010 – 12/2010

Reversica is a company designing and manufacturing articulated shelving units.

Design and fabrication of wood shipping containers for Reversica shelves.

Part-time position 1-2 containers per week.

Plywood and Douglas fir construction with sheet foam insulation.

Volunteer Delivery Driver, GRAY BEARS of CALIFORNIA, Santa Cruz, CA 01/2009 – 12/2009

Delivered produce to the elderly every Thursday.

A different route every week around Santa Cruz County.

Electro-Mechanical Engineer, REVERSICA DESIGNS, Santa Cruz, CA 01/2005 - 12/2008

Design and manufacture of articulated multi-media shelving units.

Multiple projects, adding motors with controllers to shelves.

Procured 24VDC gearmotors, designed motor frame with lead screw/arm.

Designed prototype transistor full bridge bidirectional motor driver.

Designed prototype logic with opto interrupters limit switches.

Designed prototype motor current foldback analog circuit.

Designed prototype remote control circuit.

Laid out 2 sided PCB of proven circuits with OrCAD PCB and BOM.

Procured 24VDC 10A SMPS from Triad power supply company.

Part-time contract position.

Electro-Mechanical Engineer, ECO SYSTEMS, Santa Cruz, CA 04/2002 – 10/2004

A company designing and installing commercial solar photovoltaic systems.

Layout of internal components and point to point wiring of transducer housing.

Installation of portable metrology unit on roof of building/routing cable.

Design and fabrication of solar panel simulator circuit, machined enclosure.

Design and fabrication of 0 – 96VDC voltage regulator for testing transducers.

Rewired solar panel on roof with larger gauge wire.

Performed testing of transducer units on interface connected to a computer.

Assembled components on perf board for 24VDC 3A linear power supply.

Machined 10 transducer housings on drill press, used file to square holes.

Programmed/tested FPGA interface for satellite computer system.

Sr. Engineering Technician, CALIPER TECHNOLOGIES, Inc., Mountain View, CA 05/2001 – 11/2001

A company devising and manufacturing the lab on a chip imaging system.

Performed tubing life tests on peristaltic pumps with water.

Troubleshot tray handler robots under computer control, found damaged homing sensor. Informed vendor regarding robot issues.

Burned – in system overnight at 104 degrees, temperature monitored hourly.

Prepared “Scooby doo” system for FCC testing at local lab in Milpitas.

Arranged transportation with trucking company to and from lab.

“Scooby do” failed the FCC test, so we rented a spectrum analyzer to probe the system at the office, found the source of noise-an unshielded laser cable.

Returned “Scooby do” to FCC test lab and system passed. However, when we were loading the system into the truck, we sheared off 2 castor wheels.

Electrical Cable Design Engineer, PHOTON DYNAMICS, Inc., San Jose, CA 10/1999 – 12/2000

A company designing and building LCD panel inspection equipment.

Designed and fabricated digital video cables used ribbon cable for prototype.

Discovered overheating of Coreco video processor PCB’s caused by the ribbon cables blocking natural convection cooling.

Redesigned digital video cables SCSI round to ribbon IDC connectors.

Designed cable harness for Linear Variable Displacement Transformers.

Devised daughter board analog circuit to drive Voltage Controlled Air Pressure Valves.

Performed adjustment (zero) of LVDT’s mounted in sensor chuck.

Added remote voltage sense to all the SMPS to compensate for voltage drop

Assisted junior EE with troubleshooting his PCBA, discovered that all the memory IC’s were all on at the same time (shorted) suggested he add some chip select lines.

Drew block diagrams of the VME cards, since no documentation existed.

Reprogrammed both FPGA’s on VME card for driving Voltage Controlled

Air Pressure Valves.

Engineering Technician, ULTRA STEREO LAB, Inc., San Luis Obispo, CA 04/1999 – 10/1999

Calibrated USL cinema audio encoders/decoders used audio level meter.

Made suggestions for better PCB layouts on cinema optical soundtrack reader.

Designed optics calibrator with target, beam splitter and video camera.

Devised LASER light source to replace LED illuminator for soundtrack reader

Reversed engineered the DOLBY digital cinema audio decoder card rack.

Assisted other technicians with troubleshooting and circuit test.

Electrical Cable Design Supervisor, KLA TENCOR, Inc., San Jose, CA 03/1998 – 06/1998

Supervised 2 draft persons in engineering department.

Checked the drawings for errors ie; missing references, wrong dimensions, wrong connector(s), missing labels, etc.

Completed drawing numbers entered into Excel and drawings on AutoCAD.

Power Supply Engineer, AmPRO CORPORATION, Mountain View, CA 01/1997 – 10/1997

A company developing a novel LIQUID CRYSTAL LIGHT VALVE projector.

Supervised development of new power system from Canadian supplier, had weekly calls with power supply engineers to stay on target.

Received 1st article prototype power system 3/97, put in projector for test.

Assisted production with maintenance of LCLV test equipment.

Received 5 more power systems 5/97, put in 5 projectors for test.

Attended INFOCOM trade show in Los Angeles. After the show helped broadcast engineer with video switcher issue on AmPRO projector, I just looked at another projector and it’s connection, then connected ours the same way and viola it worked. The BCE called me a schoolboy.

Tested projector lamp overtemperature sensor circuit.

Found replacement multiplier IC to replace discontinued multiplier IC.

Electrical Engineer, WATKINS – JOHNSON SEG, Scotts Valley, CA 12/1995 – 09/1996

A company producing Atmospheric Pressure Chemical Vapor Deposition furnaces for semiconductor wafers. The WJ999 and WJ1000.

Designed several different cable harnesses for the WJ999 furnace.

Assisted Mechanical Engineer with electrical issues with his project.

Found replacement power supply for thermo guard control unit, purchased 25 power supplies for customer service.

Wrote the first Source Control Document for a circuit breaker enclosure.

Discovered overheating issue with PLC, unit was mounted in wrong orientation – it was mounted on it’s back, instead of it’s side- so there was no convection cooling – all the heat was trapped over the power supply. I turned the PLC, some cables needed to be changed (length mostly).

Attended SEMICON trade show in San Francisco for 1 day.

Troubleshot some robots for the WJ999 and discovered that all the robots have the same failure the Z axis. I got a new robot from customer service and went to the lab, hooked up some power and removed the covers on the robot, using a oscilloscope I measured voltage and current in transistors and found that the X, Y, Z, all used the same rated motor driver circuit. But the Z axis draws more current than X and Y. I presented my findings to the President and chief Engineer of the robot company in person at WJ – SEG. They said that they would repair all the robots in 6 months for free.

Electrical Engineer, TECHNICAL INSTRUMENT COMPANY, San Jose, CA 01/1995 – 11/1995

A company developing a LASER scanned confocal microscope system with a EISA PC computer, RS – 170 video cards, galvo meters, photo multiplier tubes, linear power supply.

Redesigned PMT PCB’s added analog/digital ground planes, +5, +15, -15 power planes, added PMT amplifier daughter card, single point ground.

Calibrated PMT PCBA on bench with power supply and a oscilloscope.

Calibrated Galvo PCBA on bench with power supply and 4 channel scope Galvo has proportional, integral and derivative control loops.

Optimized LASER location to PMT photo cathode region for max signal.

Designed aluminum housing for PMT isolated from analog/chassis ground.

Designed end plate for PMT housing isolated from chassis ground.

Placed biological sample on microscope and viewed on computer monitor.

Designed PCB for power supply +5, +15, -15 backplane interface to rack.

Responsible for construction of 5 control towers, PMTx2, Galvo and P/S.

Programmed FPGA for 8 and 12 bit serial data transmitters.

Fixed problem with 8 bit serial data transmitter, added inverter to reset line

Modified black level amplifier so we could get are “IRE” up 0 – 70 millivolt.

Loaded software 10 discs into EISA computers times 5.

Engineering Technician, MICRO – CRAFT, Co., Ben Lomond, CA 06/1994 – 10/1994

Owner Klaus Schambeck HW/SW Engineering.

Soldered components to vector board for MOSFET audio amplifier.

Checked circuit with a voltmeter and an oscilloscope, audio oscillator.

Attached a full range speaker for power tests.

Mounted and soldered components to PCBA that Klaus laid out Eagle CAD.

Tested PCBA on bench with DMM and an oscilloscope, waveform generator.

Assisted engineer with troubleshooting radio frequency circuits.

Assisted engineer with servicing switch mode power supplies.

Power Supply Design Engineer, PIONEER ELECTRONICS, Inc., Fremont, CA 03/1994 – 05/1994

A company attempting to design hot swap switch mode power supplies.

Engineer/manager put diodes in the SMPS outputs (2 power supplies) and said it was hot swappable.

We had a lunch meeting with Power One power supply engineers and the engineer/manager explaining how hot swap works, the other PSE shaking their heads. So I stepped up and said “the safety ground has to connect first” “then the neutral and the live” and “the SMPS need current sharing circuitry. The PSE’s said finally someone who knows what he’s talking about.

We used an Elcon connector for the AC input with variable length pins.

Worked with Power One engineers to develop current sharing circuit.

Delivered 1st article unit to HP Cupertino 2 weeks late.

R & D Engineering Technician, CPI NAD, Inc., Fremont, CA 03/1993 – 09/1993

A company designing and MFG custom switch mode power supplies.

Assisted Sr. research fellow with bring up and testing of prototypes.

Assembled and soldered components to breadboards.

Wound transformers, gapped ferrite cores with Dremel diamond bits.

Selected heatsinks for MOSFETS and power diodes.

Used isolation transformer, variac, electronic loads, oscilloscope, digital wattmeter, DMM.

Drew rough schematic of prototype power supply.

Performed Bellcore Mean Time Between Failures calculation.

R & D Engineering Technician, CPI NAD, Inc., Fremont, CA 06/1992 – 12/1992

A company designing and MFG COTS switch mode power supplies.

Assisted Sr. research fellow with assembling copper clad breadboards.

Proposed one piece copper foil transformer secondary winding.

Introduced S R fellow to insulated aluminum substrates (PC metal).

Laid out power devices on 5 mil thick PCB 4x.

Delivered ferrite cores to transformer vendor for custom gapping design

N-CH MOSFET for main switch and P-CH MOSFET for clamp winding.

Power supply control circuit designed in Ireland and shipped to Fremont

Assembled 1st article prototype power supply, control and power devices on insulated metal substrate.

Electrical Design Engineer, PI SQUARED, Ben Lomond, CA 02/1992 – 06/1992

A company designing and producing intelligent display-display units.

Laid out single sided PCB backplane for 9 displays and SMPS.

Laid out single sided PCB’s 9 different display types.

Hired assy technician to assemble display boards-9 units in all.

Assembled backplane, 9 switches, some jumpers and 1 power supply.

Mounted backplane to sheet metal base and covered with curved plastic cover.

Sent 1st article unit to customer for approval.

Engineering Technician, POWER CONVERSION AMERICA, Inc., Fremont, CA 04/1991 – 12/1991

A company designing and manufacturing switch mode power supplies.

Project: 500 kHz Forward DC to DC converter, 5VDC @ 30A output.

Mounted and soldered components to copper clad breadboard.

Used variable DC lab supply and oscilloscope to bring up converter.

Consulted Power Supply Engineer when problems/issues arose.

Interfaced with PSE when he was working on the DC - DC converter.

Laid out prototype PCBs for control and power devices.

Performed preliminary Bellcore MTBF calculation.

Electro-Mechanical Engineer, DESIGN ENGINEERING SERVICES, Saratoga, CA 01/1991 – 03/1991

Company run by 2 brothers, HW/SW design.

Project: uninterruptable power supply and battery charger.

24VDC input, 300VDC output push-pull PWM converter.

SCR battery charger circuit for 24V lead acid batteries.

Laid out single-sided PCB’s manually for converter and charger.

Mounted everything in 19 inch rack.

Electro-Mechanical Engineer, PI SQUARED, Cupertino, CA 12/1990 – 12/1990

Mechanical Engineering design company.

Project: Liquid color imaging system.

Used video camera without lens for closeup imaging of liquid in clear plastic tank.

Purchased portable color TV set, picked off RGB signals and connected them to 3 National Instruments analog to digital cards.

Used DMM to construct color/voltage matrix.

Mounted everything to particle board base.

PI SQUARED delivered assembly to the customer.

Class of 1980, 10 year reunion for Hong Kong International School 06/1990 – 06/1990

Reunion in Redondo Beach, CA.

Towed “DINKY” with my Honda Civic from San Jose to Los Angeles.

Parked Civic at hotel, drove Dinky to reunion dinner in Redondo.

Parked Dinky in front of Chinese restaurant.

After dinner drove to Hollywood, to cruise Hollywood Boulevard.

The crowd went wild when they saw Dinky.

Towed Dinky to the beach for the second day of the reunion.

After conversing and saying our goodbyes, drove to Paso Robles.

Stayed the night in Paso, then drove back to San Jose.

RF Engineering Technician, SUN MICROSYSTEMS WSD, Mt. View, CA 01/1989 – 12/1989

Division designing and building computer work stations.

Assisted RF Engineer with design and testing of RF systems.

Project: Video and keyboard extender for Disney animation.

Issues RFE was convinced that LMB modular cabinet would pass the FCC test, because he sanded off the paint on the cabinet. So when we did the indoor test at SUN, the box was leaking like a sieve. I told him that we need an extruded cabinet with airtight end plates and screws every inch.

Issues with extender PCBA, RGB channels should be laid out the same.

Four 100 foot long coax cables per unit, RGB+H.

Two extender units, transmitter and receiver.

Designed connector system for power supply test system.

Tested power supplies on test system using Lotus 123 program.

Hi potted power supplies.

Engineering Technician, ENDOTHERAPUETICS, Inc., Redwood City, CA 04/1988 – 12/1988

A company designing medical test equipment.

Assisted EE with activities related to the Uroscan product.

Troubleshot analog and digital circuitry to the component level.

Battery endurance testing, nickel cadmium cells.

Battery charger performance testing.

Laid out double sided PCB for Uroscan 2000, urine flow meter.

Complete PCB with solder mask and a silkscreen.

Mounted and soldered by hand components on the board.

Checked PCBA for solder bridges, solder wicking, removed flux with fluid.

Charged battery, then tested PCBA analog and digital circuitry.

Placed unit in oven for burn-in.

Removed unit from oven next day and tested again.

Printed Circuit Board Designer, Y. K. SYSTEMS, Co., South Korea/Cupertino, CA 01/1988 – 04/1988

CPIs power supply manufacturer in Incheon, South Korea.

Laid out 10 different PCBs on plastic 1:1 with dry transfers.

Reversed layouts for negative resist, exposed boards with UV

Developed boards, then put in the etcher, remove from etcher, rinse with water, use steel wool to remove resist, drill holes with carbide drill bits, put in tinning solution, remove rinse with water and dry with a paper towel, and viola!

Engineering Technician, LUMISYS/MOLECULAR DYNAMICS, Inc., Sunnyvale, CA 09/1987 – 12/1987

Two companies sharing one building.

Lumisys product LASER scanned Xray film digitizer system.

Integrator tube with 2 head-on photo multiplier tubes.

Galvo meter for LASER scanning of integrator tube.

Designed/fabricated flyback power supply 700VDC for PMT.

Laid out prototype PCB for PMT analog circuitry.

Molecular Dynamics product LASER scanned biological sample imaging system.

Constructed motorized LASER beam rotary spatial filter.

Wire wrapped digital logic ICs for system controller.

Japan Stereo Company, Ltd., Independent Electronics Contractor 09/1987 – 03/2023

Test Engineer, COMPUTER PRODUCTS BOSCHERT, Milpitas, CA 01/1984 – 09/1987

Company producing custom switch mode power supplies

Designed test cables, test fixtures, unique test equipment

Performed field service of our own ATE in Ireland,

Mexico, Spokane WA and South Korea (Incheon).

Hi potted power supplies at customer site in Phoenix, AZ.

Trained ATE technicians on system operation.

Research & Development Technician, CPI COMPOWER DIVISION, San Jose, CA 01/1983 – 12/1983

A company producing a novel custom switching P/S.

Built power supplies from VP of engineering schematics.

Wound transformer with bifilar windings.

Push-Pull PWM converter, LM3524 control IC.

Brought up converter under VPs supervision.

Documented final schematic.

Next R&D project Half Bridge power supply.

Another R&D project Forward power supply

Drew schematics for ATE system rack cards.

Designed exterior panels for the ATE cabinet.

Assisted with construction of 15 ATE systems.

Power Supply Repair Technician, COMPOWER CORPORATION, San Jose, CA 01/1982 – 12/1982

Incoming power supply inspection, check fuses first.

Used DMM to check main switch, shorted yes/no.

Unsoldered parts like resistors, capacitors, transistors.

Soldered in parts with acid core flux, clean with water.

Used isolation transformer, variac, analog wattmeter, DMM.

Repaired 10 to 20 power supplies per day.

EDUCATION

Wyo Tech Automotive Technology Center, Fremont, California 03/2014 – 06/2015

10 course program for Automotive Technician Diploma, GPA 3.88.

50% in the classroom and 50% in the shop, test every week.

Cabrillo College, Aptos, California 09/2005 – 06/2006

Astronomy 1, Maya 6, AutoCAD 2006

De Anza, College, Cupertino, California 09/1988 – 01/1989

Morales & Ethics, Automotive Technology 1

Foothill College, Los Altos, California 09/1981 – 06/1983

Associate of Science degree in Electronics Engineering Technology, GPA 3.50.

Mount San Jacinto College, San Jacinto, California 09/1980 – 06/1981

Mechanical Drafting, Economics 1, Introduction to Computers, Art 1 Drawing

Hong Kong International School, 1 Red Hill Road, Tai Tam, Hong Kong 01/1978 – 06/1980

Technical Drawing, Technical Writing, Electronics, Physics, A/V Assistant

High School Diploma, GPA 2.50

Cupertino High School, Cupertino, California 09/1976 – 12/1977

Mechanical Drafting, Electronics I & II, Television Production (CCTV), GPA 3.00

Contact this candidate