Assembly Production Manufacturing Engineer

José Ruben Acosta Monge

Phone Number 423-***-****

Personal E-mail: *********@*******.*** and ***********@*****.*** Address in USA

**** ******* *** *** ***

Chattanooga, Tennessee, 37421

Address in Mexico

Cibiribaro # 28

Colonia: Nuevo Hermosillo

Hermosillo Sonora México

CP: 83296

NOTE: I do not need a visa sponsor (I’m Green Card) Objetive

I work in the labor activities in a way that contributes to the development of the company and my personal development, performing my tasks with responsibility, dedication, enthusiasm and excellent quality.

Professional Education:

Engineer in Tecnologías de la Informacion, Universidad Tecnologica de Hermosillo 2007-2011.

Professional ID number : 7614853

Work experience

Gestamp Chattanooga II

8011 Volkswagen Drive Chattanooga TN, 37416 USA

Process and IT Engineer

• KPM (Key Performance Measures)

• Take cycle times to balance lines

• Creation of Statistics for the production of stamping and assembly

• Elaboration of Pareto for the main Downtime problems

• Creation of Databases for Stamping and Assembly

• Create daily reports from Captor (Global Database of Spain)

• Captor leader at Gestamp Chattanooga II

• Creation and update of Work instructions, Visual Aids and Formats of Stamping and Assembly

• Communication connections on all company computers

• Creation of remote connections between computers

• Construction of communication cables for computers, Switch, Modem etc.

• LPA Auditor

• Continuous improvement with close collaboration of the different areas.

• PDCA

• Problem solving using 8 disciplines, DMAIC, cause and effect analysis and some more.

• Update of AMEF, Control Plan

• ISO 9001:2015 & IATF 16949:2016 Internal Auditor

• Leader of the area of operations for current product and new models

• Leader of stamping and assembly production supervisors

• Make decisions to run production lines based on inventory.

• Programming and elaboration of databases in Power BI

• Power BI report and charting

Sonora Forming Technologies

Blvd. Henry Ford # 43 Park

Industrial Dynatech south Hermosillo Sonora

I. Quality Stamping supervisor June 2005 - June 2007 II. Manufacturing Engineer Assembly / Stamping June 2007-July 2014 III. Quality chief July 2014 - January 2017.

• Supervisor of stamping presses (Transfer, Coil transfer, Tandem, and progressives- Establish safety standards in your area and communicate them to all your staff.

• Train and develop staff in working procedures and operational controls for the environmental aspects of their area that may impact the environment

• Generate an environment of Cost Reduction among collaborators that contribute to increase the profits of the company

• To promote the constant Development of the collaborators as well as a good working environment

• Coordinate and ensure activities that directly influence the product are adequate to achieve customer satisfaction

• Control and improvement of PPM

• Standardization of operations.

• Immediate feedback in case of customer complaints, external and internal

• Follow-up and implementation of Continuous Improvement of Cost Reduction.

• Saving of productive and non-productive material necessary for the production of the product.

• Monitor the effectiveness of corrective actions to reduce quality defects and Scrap.

• Dimensional engineering supervisor (Stamping and Assembly)

• Communication and customer visit (preventive work)

• Promote and be the leader in the necessary activities both internal and between departments to have the product in time and the amount required

• Generation of 8D analysis, DMAIC and its follow-up

• Improvement and implementation of continuous improvement within productive lines

• ISO TS 9001

• ISO 14000

• APQP

• PPAP

• AMEF (PFMEA,DFMEA)

• Control Plan

• HOE, HIE, Rework IT

• Continuous participation in the improvement of productive processes and monitoring and verification of times and movements

• Engineering Changes.

• Measurement and creation of programs with equipment of CMM (Coordinate measuring machine) and data collectors (Datamyte)

• Quality Chief

• Data Management, suppliers, customer Tier 1 Tier 2 OEM

• Management of staff to develop templates for the customer

• Coordination of CM4D to upload data to Ford platform

• Coordination and release of measurement tools inside and outside the country

(Korea, Japan, Canada and USA).

Ford Motor Company

colorada road Km 4.5 Industrial park south Hermosillo Sonora.

-Universal technician April 1989 to 1993 body repair and painting

-Incoming quality 1993 to 1996

-CMM programmer 1996 to 2005

• Body or dent repair (“A” Class).

• Tracking supplier issues

• Elaboration of QR (Quality Rejet)

• Monitoring of PPM (Bad Parts per Million)

• Development of measurement programs for CMM (Coordinate Measuring Machine)

• Measurement to Body Shell, Body Side, Quarter Wheel House, Front Floor etc.

Computer Packages:

Windows Management 95%

MS Office Management 95%

Ingles 70%

SAP 3 Program Medium level

Ideas 75%

Catia 70%

Mtplaner 75%

Pdgs 90%

AutoCAD 85%

PCDmis 90%

LKDmis 90%

FARO 85%

ROMER 85%

Visual Studio 85%

C++ 85%

Borlan C 85%

Phyton 85%

Flash 85%

Inventor 80%

SpinFire Ultimate 85%

Teamcenter Vis 85%

Teamcenter Vis Mockup 85%

Power BI Programming 85%

Contact this candidate