Quality Inspector Control

Nijanthan S

No:***, YadhavarStreet, Narthampoondi,Thiruvannamalai-606802, Tamilnadu, India

Mobile: +91-934******* Email: ********@*****.***

Seeking assignments in QA Line inspector

Synopsis

A dynamic professional with around 3 Years of experience in Sanmina as a QA Line Inspection

A Capable Quality Control Inspector who can quick to identify any production shortcomings or wrong doing

Mark Can Continuously Monitor Production Procedures to Ensure that all Manufactured Goods confirm to the Highest Applicable Specifications

Has a Track Record of Straitly Following Inspection Procedures to test Products to Uncovered Defects

Organisational Executive

Presently associated with – Sanmina SCI india Private Limited(2017-2021), at Tamilnadu Chennai.

Key Result Areas

Auditing 5S at All Working Stations Before Shift Starting

Monitoring and Examining Each Stage of Production

Ensuring that all testing is Performed to Highest Standard

Distributing Written Quality Assurance Results to Appropriate Parties

Identifying Problems and Suggesting Solution

Monitoring All inspection and testing Equipment to Ensure Current and Valid Calibration

Identifying Unsafe Working Practices

Making Sure that Company Employees Follow Documented Procedures and Standards

Carrying Out Final Inspection

Making Sure that Labels are Accurate

Writing up Reports for Quality Managers

In Sundaram Fasteners Pvt Ltd (As a Quality Inspector)- (Jun -2013 to Feb-2016)

Preparing the control chart for every shift.

Shift Scrap Details Updated in SAP.

SOP (Standard Operating Procedure) Checking at line side,

Check sheet and Histogram Sheet also maintained itself,

Every ten minutes Job Inspection done at line side,

For Every Setting Job (New Product) Inspection has to be done (Based on Mark up Drawing) and Preparing the setup approval to start the production.

Based on Line side Equipments (Vernier Calliper, Micrometer, Depth Gauge, Multi Gauge and etc...) All Jobs Inspection done by itself,

Setup Approval Preparing For the new Product Using Standard room inspection gauges (Roughness Value, Roundness Tester, Profile Projector and Contour tester),

Analyse the CMM (Co-Ordinate Measuring Machine) Reports and make the correction about the product,

For All Jobs Final Inspection make for 100% to Avoid the customer complaints,

Position Gauge (Inlet and outlet position) modified for Different types of jobs Based on the Organisation Standard.

Achievements

Improved the Quality of product,

Reduced the customer complaints,

New Process Implemented for Running the line while Gauges has getting hanging,

At Pre Washing Machine manpower reduced from 2 to 1 for the same process,

Educated to Production members for time saving Activity (Combination tool change).

Quality Confirmation done at Vendor Ends to Confirm the Quality of Job (Around 7 Concerns Identified).

At Mille bore inspection based on tolerance (max 5mg) variant type of jobs (6 types) inspected itself.

Qualification Details

2013 BE (Mechanical Engineering) from Oxford College Of Engineeringdirectorate of technical education with 70%

2010 Diploma in Mechanical Engineering from SRI Polytechnic College Vandavasi Directorate of Technical Education with 78%.

2008 Higher secondary maths group from government higher secondary school narthampoondi directorate of state board with 61%

Academic

Projects

BE Projects

DESIGN AND FABRICATION OF HYDROGEN RUNNING ENGINE

From the aforementioned discussion, it is clear that there is definitely improvement in the performance of the engine is run on the blend ‘ox hydrogen’ and conventional fuel, ‘diesel’ here .Further, the presence of ‘oxy-hydrogen’ in the combustion chamber supplies additional oxygen which leads to completed combustion of the air fuel mixture.

Thus the pollution is greatly controlled as the products that would-be produced due to burning of conventional fuel and are reduced due to complete combustion. Water vapor is one of the by-products of the combustion process with the blend of ‘oxy-hydrogen’ and diesel. Presence of water in the combustion chamber. Thus there are little chances of ‘detonation’ which is the major factor during increased power delivery of any engine .Also formation of water vapor does not allow deposition of the carbon on the cylinder wall and keeps the combustion chamber clean which further increases combustion efficiency.

Diploma Projects

DESIGN AND FABICATION OF MOTORIZED POWER HAMMER

This pneumatic forging hammer is widely used forging works, such bending out upsetting, punching, chiselling, forge, welding, bending & twisting it is also for forging in blaster dies.

Date of Birth: 10th Jun, 1991.

Place:- Signature

Date:- (S Nijanthan)

Contact this candidate