Concrete Finisher/ Carpenter/warehouse production

Bryan A. Saunders

**** ****** *****

Winston-Salem, NC 27105

Day Phone: 360-***-****

Email:********@*****.***

OBJECTIVE

To obtain employment within the Construction,Aviation,or Masonry field that will utilize skills obtained through machinery operation, building,molding,assembling construction and concrete finishing.

WORK EXPERIENCE

Atrium doors and windows

2012 to 2014

Assembly of windows and doors,

Training new hire etc

Blythe construction/Flatiron

Pipe laying n concrete finisher

02/2016 to 05/2017

Southeast connections

04/2019 to 07/2022

. Concrete finisher/Paving

Building forms to lay concrete sidewalks, curbs, and driveways after new gas lines are set, replacing temporary colpach with asphalt and etc Housing Authorities of Winston-Salem 06/2014 - Present Carpenter

•Measure and mark cutting lines on materials, using ruler, pencil, chalk, and marking gauge.

•Follow established safety rules and regulations and maintain a safe and clean environment.

•Verify trueness of structure, using plumb bob and level.

•Shape or cut materials to specified measurements, using hand tools, machines, or power saw.

•Study specifications in blueprints, sketches or building plans to prepare project layout and determine dimensions and materials required.

•Assemble and fasten materials to make framework or props, using hand tools and wood screws, nails, dowel pins, or glue.

•Build or repair cabinets, doors, frameworks, floors, and other wooden fixtures used in buildings, using woodworking machines, carpenter's hand tools, and power tools.

•Remove damaged or defective parts or sections of structures and repair or replace.

•Lay and finish concrete on outdoor sidewalks, walkways, or parking lots.

•Install structures and fixtures, such as windows, frames, floorings, and trim, or hardware, using carpenter's hand and power tools.

•Finish surfaces of woodwork or wallboard in houses and buildings, using paint, hand tools, and paneling.

•Arrange for subcontractors to deal with special areas such as heating and electrical wiring work.

•Work with and/or remove hazardous material.

•Cover subfloors with building paper to keep out moisture and lay hardwood, parquet, and wood-strip-block floors by nailing floors to subfloor or cementing them to mastic or asphalt base.

•Fill cracks and other defects in plaster or plasterboard and sand patch, using patching plaster, trowel, and sanding tool.

Moncreiff Construction 7/2005 – 11/2008

Concrete Finisher

•Supervised and motivated hourly employees

•Set all forms that hold concrete to the desired pitch and depth, and align.

•Spread, level, and smooth concrete

•Expertise in use of rake, shovel, hand or power trowel, hand or power screed, and float.

•Mold expansion joints and edges, using edging tools, jointers, and straightedge.

•Monitor wind, heat, or cold affects curing of the concrete throughout process.

•Blueprint reading

•Signal truck driver to position truck to facilitate pouring.

•Move chute to direct concrete within forms.

•Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.

•Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.

•Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.

•Polish surface, using polishing or surfacing machine.

•Sprinkle colored marble or stone chips, powdered steel, or coloring powder over surface to produce prescribed finish.

•Build wooden molds, and clamp molds around area to be repaired, using hand tools.

•Check forms that hold the concrete to see that they are properly constructed. BeAerospace 8/2005-10/2009 fill n fair

Moldings,building,measuring,prep work before being sent to paint, having to stamp and sign off on every part that passes my station

Teamsters local 528/Cement Masons 2002-2005

Laser screed operator,using walk-behind machines, form building before poors,rebar tieing etc.

EDUCATION

Forsyth Technical Community College

GED / wa.st apprenticeship program certification/Whatcom Community College REFERENCES

*Available upon request

Contact this candidate