Engineer Electrical Commissioning

Name ADRIAN STOICA

AddressBd Ferdinand Nr ** BL AR3 Sc A Ap 5 Constanta, 900704, Romania

Phone +40-722-***-***

Email ********@*****.***

OBJECTIVE

Looking forward for next I&C NPP assignment.

PROFILE

More than 30 years Automation and Control experience of which 19 years I&C nuclear experience in engineering, commissioning, operation and maintenance for CANDU PHWR, Westinghouse AP1000, KEPCO APR1400 and OL3 EPR PWR.

China Haiyang AP1000 commissioning activities covered for more than 2 years I&C component and system pre-op tests, Ovation and engineering change support, troubleshooting issues identified during commissioning and system turnover to operation.

More than 13 years activity at Cernavoda Candu NPP were performed in engineering, commissioning, process software and preventive maintenance departments, having various main responsibilities: development of Component and System Health Monitoring Programs (CHMP, SHMP) for I&C systems under jurisdictions, troubleshooting coordination, controller replacement, software change validation, I&C information report.

UAE Barakah APR1400 and OL3 EPR I&C commissioning activities created a general overview of main nuclear projects. Experience obtained can be used in other projects. WORK EXPERIENCE

June2021 - Mar 2022 Overall Commissioning I&C (Expert Team) - OL3 AREVA

● Support for the issuance or update of the commissioning test documents

● Check of RFA MoM during the Nuclear Commissioning Phases

● .Review of commissioning test result assessment performed by the Commissioning Branches before the submittal of the commissioning test result documentation to TVO (signature as commissioning expert checker)

● Support for the analysis of deviations identified during the commissioning activities and check of the Commissioning Clarification Request

● Support for the analysis of technical changes and validation of the corrective actions defined through the technical changes impacting commissioning test documentation and/or commissioning activities on site (commissioning tests or retests)

● Analysis of the experience feedback from other EPR™ Projects that might impact the commissioning activities.

Sept 2019 – Dec 2020 Senior Instrumentation Maintenance Specialist I&C – BNPP UAE

● Conduct l&C maintenance job tasks in a timely manner and with quality to achieve operational readiness and to operate with the highest level of safety and reliability.

● Maintain or oversee the maintenance of the containment l&C equipment, specifically the reactor protection system, engineered safety future actuation system, radiation monitoring system, seismic monitoring system, and the control, monitor, and protection instruments for all containment related systems to ensure appropriate function according to APR1400 Technical Specifications.

● Oversee Long Term Maintenance Strategies (LTMS) and supervise contractor activities to ensure implementation according to standards.

● Execute troubleshooting process on l&C systems and equipment to ensure that issues are resolved correctly and in a timely manner.

● Procedure Change process support

● Mentoring and guidance for team members.

May 2019 – Aug 2019 Commissioning Engineer Westinghouse France - St Alban

● DUS I&C Commissioning activities

● Mentoring and guidance for team members..

March 2018 – Aug 2019 Senior EIC Engineer – Kinectrics Nuclear Romania

( remote part-time from May 2019)

● I&C and Electrical design activities for CANDU projects.

● Project management support for progress evaluations and other specific activities.

● Ensure quality control for all deliverables issued and verified.

● Mentoring and guidance for team members.

July 2015- June 2017 Senior Commissioning Specialist III Haiyang AP 1000 – Wectec

● Conducting test activities in MCR or field per the commissioning schedule and commissioning management procedures

● Tracking system installation status and providing feedback to the Schedule Group

● Preparing commissioning procedures, reports and packages and evaluating the results, recording and reporting deficiencies found during tests

● Ensuring the implementation of a QA program in assigned commissioning systems

● Mentoring and guidance for I&C hardware and software engineers

● HVAC, Chilled and Hot Water, Electrical and DG system support

● Ovation PLS activities for systems under jurisdiction:

● Control Logic Review for allocated I&C system

● Baselines testing and implementation

● Tuning of control loops

● TMOD supervision for allocated I&C systems

● EDCR verification

● Troubleshooting open items identified during system test

● PMS interfacing

● Testing & troubleshooting of implemented controls and graphics June 2002 – July 2015 CNE CERNAVODA -NPP

March 2013-July 1015 Senior I&C Responsible Component Engineer ( RCE)

● Marconi & Nuovo Pignone Control Systems Programmable Digital Controllers

● CyberSecurity CSP implementation for Process Systems Main Responsibilities:

● Fisher & Porter 53MC5000 Controller replacement (installation, wiring, configuration)

● Emerson DVC6200 digital valve controller installation, cabling, wiring and configuration Technical Assistance in implementation (installation, cabling) of I&C Design Changes Preventive Maintenance Strategy for Electronic Cards and Controllers

● Preparation and validation of I&C procedures (NOP, APOP)

● Component Health and System Health Monitoring Assessment (CHMP, SHMP)

● Control Loop Performance Assessment -DCS replacement installation for digital and analog control systems

● Electronic Controllers design and software change coordination -Evaluation of maintenance procedures for reactivity control loops (valves, positioners)

● Validate field installation consistency with the documented design after modifications.

● ISO 27001 Risk Assessment

● Cyber Security Plan coordination CDA (RG5.71 10 CFR 73.54, IAEA NSS 17)

● Oversight of preventive maintenance activities

October 2007 - March 2013 Responsible System Engineer (RSE) – Digital Process Systems and Special Instrumentation

● MICROMOD MC500 control station FTRAN programming

● DCC (Digital Control Computers)

● T/G Control Interface (GE Mark VI)

● Boiler Level Control

● Boiler Pressure Control

● Reactor Regulating System

● Desktop Simulator

● Overall Plant Control

Main responsibilities:

● I&C Software Design Change preparation & implementation

● Spent Fuel Pool Temperature Loop Design and Implementation

● Main Steam Reheat Pressure Control Design

● Boiler Power Status Display Design and Implementation

● Supervision of installation, wiring, cabling of new digital I&C equipment

● Interfacing DCC with DCS and MARK VI (Turbine Control System)

● Control Loop Performance Assessment

● DCC Interface with Plant Full Scope Simulator (Desktop Simulator)

● Technical review of procedures for systems under responsibility

● Preparation of information reports (IR) for DCC I&C July 2004 - October 2007 Commissioning Engineer I&C DCC & Process Control

● Installation and wiring of various I&C equipment with DCC interface (temperature,

● pressure, flow and reactivity measurement loops)

● Cabling, Wiring and Test Procedures for Analog & Digital IO DCC signals

● Preparation of commissioning documents for assigned systems (DCC, Steam Generator Pressure and Level Control)

● Reactor Regulating System (installation and wiring of reactivity control panels and

reactivity instruments)

● Technical support during execution of commissioning tests in phases A, B and C

● DCC Software Station Instruction preparation -Preparation of commissioning reports for all phases (A, B and C)

● Coordination of DCC Software Audit activities

● Interface with other commissioning departments

● BLC Tuning and Boiler Pressure Control Interface DCC/MARK VI June 2002 - July 2004 Design Engineer Electrical C&I Engineering Department

● Assistance of construction and commissioning groups in the solution of engineering problems related to Digital Control Computers (cabling, wiring, ST&PT procedures)

● Assessment of reactivity control panels, flux detectors, ion chambers and preparation of design documentation for installation, cabling and wiring of various I&C systems

● Detail design for Plant Digital Control Computers, Reactor Regulating System, Failed Fuel Location System, BLC and BPC

● Review of technical documents (design manuals, program specifications, operating manuals) and ensure adequacy with design objectives

● Approve and generate field design changes during installation and commissioning, update design and operational documents

● Software Categorization (CSA CAN3 N290.4, COG 95-264.I)

● Verification, Validation and version control coordination of Computer Software Changes

● Version control and oversight support

March 1993 - June 2002 AUTOMATIX IND LTD Software Engineer / Project Leader/ Technical Manager

● Design, manufacturing, commissioning, maintenance of energy dispatcher systems for all families: -F1 (Z80 implementation) -F2 (80C51) -F3 (PC data acquisition)

● Supervision of installation, cabling, wiring and maintenance for energy dispatcher and data acquisition systems HMI interface programming for QNX and Windows platforms for F2&F3 Automatic Data Logging (ADL) implementation

● Monitoring & targeting implementation for SUBEX Bacau (Phare Grant)

● NPP U1 Benson Printer Replacement project

● Industrial data acquisition systems design and manufacturing: Power Factor Controller, Temperature Controller with TCP\IP Interface

July 1986 - March 1993 INSTITUTE FOR COMPUTERS ( ITC-Constanta Branch) Researcher ( CP3)

● System and application software for various military projects using 8 and 16 bit microcontrollers Intel & Zilog families

● Fast Radio Modem (Innovation Certificate)

● Digital and Software Design Mobile Data Acquisitions System (Innovation Certificate)

● Application Software and System Design

● Digital PLL Design and Implementation

● Embedded System Software Design

September 1981 – July 1986 R&D INSTITUTE FOR AUTOMATION (IPA - Constanta Branch) Software Engineer

● Software Design for 8 and 16-bit microprocessor systems

● Automatic Radar Plotting Aid (ARPA), tracker and display system design.

● CP/M implementation on MYCRON computers

● Design of Weather System for Nuclear Power Plant Cernavoda

● Tightly coupled and loosely coupled multiprocessor system design for ARPA and other complex applications

● Military Naval Digital Systems Design for Missile Launch System (CLT) EDUCATION

● 1976-1981 BSC in Automation & Computing University “Politechnica” Bucharest CERTIFICATES

● STARTUP AUTHORIZATION CERTIFICATION SDNPC valid until January 2021

● SAVOIR COMMUN DU NUCLÉAIRE NIVEAU 1 - valid until 2022

● HABILITATION ELECTRIQUE B1V-B2V - valid until 2022 TRAINING

● 1998 Authorware -Macromedia Marintek Norway

● 1998 Course on education for Energy Managers FEMOPET Romania

● 2004 DCC Software Training AECL Canada

● 2006 Turbine Control Systems Course GE-USA

● 2008 TCS and Excitation Advanced Course GE-USA

SKILLS

● Working level knowledge for:

- I&C systems fundamentals and their applications in process systems operations

- nuclear special instrumentation and applications

- application of digital systems in I&C systems design

- I&C Systems Design and Analysis

- installation, commissioning, maintenance of I&C instrumentation

- life cycle and configuration management for I&C components and systems

- Modbus, Profibus, Hart interfaces commissioning and testing

- NOP, ARP, AOP, GOP procedures preparation and verification

- FMEA, FTA, Defense in Depth. PSA and FSAR

● Ability to evaluate compliance with applicable I&C industry codes and standards (IEC 61226, IEC 61513, IEC 62340, IAEA SSR 2-1, IAEA DS 431).

● Familiarity level knowledge for mechanical, civil and chemical theories, principles and techniques that apply to I&C systems.

● Working level knowledge of I&C components (pressure, temperature, level, radiation transducers and transmitters from various manufacturers)

● Ability to read and interpret electrical, mechanical and P&ID diagrams

(ANSI/ISA-S5.1), engineering fabrication and construction drawings.

● Programming Languages: C, C++, Delphi, ASM, Matlab, VBA, PHP, MySQL, HTML, Java

● Operating Systems: CPM, DOS, Linux, QNX, RSX-11, Windows

● Ovation DCS expertise (logic diagram, digital and modulating control).

● Loop Control Evaluation and Tuning.

LANGUAGES

English, French very well written and spoken

PERSONAL INFORMATION

DOB 01/09/1956

Married

REFERENCES

Name: Tiwari Balendu Shekhar

Job Title: BNPP Manager

Company: Westinghouse

Phone Number:

Email Address: ********@************.***

Name: Jerome McMahon

Job Title: Technical Training Manager

Company: Nawah

Phone Number: +971*********

Email Address: ******.*******@*****.**

Contact this candidate