Performed Assembly line duties such as conformal coating and final assembly for medical boards. Solder thru hole components and rework PC boards (SMT and thru holes). Solder wires and route according to blue prints.

Performed visual inspections and under microscope by ensuring the compliance of the company policy and adherence to ISO and FDA regulations and QSP.

October 2017-April 2018

Hughes Circuit

540 South Pacific St.

San Marcos Ca. 92078

760-***-****

Work experience: Electromechanical Assembler. Build Box Assemblies.

Solder wires and route them according to blue prints. Prep. and crimp wires and cables . Performed inspections on surface mount and thru hole PCB according to ISO regulations.

Prep. components and solder thru hole .

Assist engineering for prototypes systems.

Perform complete complex assembly, wiring and cabling following engineering drawings, Bill of material, etc.

Use assembly tools such as calipers, meters, crimpers, wire machine cutter, etc.

Major responsibilities are, but no limited to perform complete complex assembly, wiring, cables, etc.

Assigned to fully train people.

December 2005- March 2006

Aerotek Commercial Staffing Services

100 San Marcos Blvd.

San Marcos, Ca. 92009

760-***-****

Principal Duties:

Assemble a home respirator device and test units for any leakage defects and perform quality inspections in compliance of the company policy and adherence to ISO and FDA regulations and QSP.

Assisting Q.A. manager for final test and inspection of finished units.

July 2004-Nov.2005

Adecco Technical Agency

5252 Balboa Ave. #502

San diego Ca. 92117

858-***-****

Principal Duties:

Prep. components and solder thru PCB. Performed visual inspection and final PCB inspections in accordance to QC standards and IPC. Rework and touch up PCB sub- assemblies using hot air and soldering iron. Electro-mechanical assembly and wiring of chassis, building cables and harness as need it.

As well reworking failed units as required.

Feb. 2002-June 2004

Schumacher Company

1969 Palomar Oakway,

Carlsbad, Ca. 92009

760-***-****

Principal Duties:

Build units for various mechanical units. Wire cables according to diagram. Test circuits for shorts and open wires. Hand assembled mechanical units using basic hand tools and performed quality inspections in compliance to ISO and FDA regulations and QSP. Assigned to train people on assembly line.

Solder components thru hole and performed visual inspection under microscope.

Cable building, crimping, stripping, cable cutting and heat shrinking..Rework and troubleshooting of failed units.

Jan. 2001-Feb. 2002

SMAC- System Machine Automation Co.

5807 Van Allen Way

Carlsbad, Ca. 92008

760-***-****

Principal Duties:

Hand assemble cables, wire harnesses, prep. components . Hand solder components on PCB. build automations box according to blue prints and in compliance to ISO and company policy. Cable building, crimping, stripping, cable cutting and heat shrinking.

Nov. 1999-Jan. 2001

EST Electronic Company

Van Allen Way

Carlsbad. 92008

Principal Duties: QC Inspector

Perform visual inspection under microscope. Inspect final boards and performed first article PCB. Keep documented results of inspections performed as well as non-conformities reports and corrective actions, in compliance of the new implemented company quality policy. Customer satisfaction being, our priority as QC department, monitoring, in process, incoming, first article and final QC performed with drawings and blue prints reading.

Jan. 1994-Jan 18, 1996

Allied Signal

991 Park Center Drive

Vista Ca.

Principal Duties:

Assemble transducer and wire harnesses according to blue prints. Performed acceptance test on wire harnesses. Connect wire harness to transducers terminals with solder. Assemble and prepare PCB and various sub-assemblies to quality control standard. Performed quality inspections on own assemblies.

Electro-mechanical assembly and wiring of chassis, building cables and harnesses.

Rework and repairs of cables as needed.

April 1989-December 1993

Labarge Electronic

11616 E.51st.

Tulsa Oklahoma 74146

Principal Duties: Mechanical Assembler

Performed assembly using variety tools and machines. Cable building, crimping, stripping, cable cutting and heat shrinking. Used assembly tools such as screwdriver, wrenches, cutters, tweezers, heat gun, wire machine cutters, etc.

Build Box assembly in accordance to Company policy, ISO 9000 .

SKILLS:

High Level Soldering

Trouble Shooting

Skilled in Mechanical Assembly

Used of Hand tools

Experienced in Quality Control

Knowledge in reading Schematics and Blue Prints

Data entry

Contact this candidate