Mitch Peters

*** **’Sun Dr.

Grand Junction Co, *1504

970-***-****

adrcwy@r.postjobfree.com

Objective

To obtain employment with a career oriented company that can provide a stable future for me and my family. I am familiar with and practiced most all areas of I&E Industrial field mainly Oil & Gas for the last 17 years. I have this experience working directly with Companies in The Parachute and surrounding areas. I have been in Management and Supervisory positions for the last 6 years. I have always prided myself in efficiency and quality in this field. I have been in the Instrumentation and Electrical profession for 30 years.

Work Experience

Southwest Electric Inc., Grand Junction Co. 8/22/2016-1/29/2017

I/E Tech

I Traveled to New Mexico, Texas, and North Dakota to complete these jobs for WPX, eog Resources, and Summit. I installed and wired Actuators, Level Transmitters, Tank Heater, Motors, and RTD’s. Installed wireless transmitters and installed and wired radio’s. Installed wireless Load Cell’s on pump jack’s and installed and wired radio’s into Lufkin controllers. Installed and wired Heat Trace. Run cable tray and pull wire for new compressor and wire appropriately for power and control.

R&A Enterprises, Carbondale Co. 4/22/2012- 8/23/2013

I/E Tech

I have been working directly for EnCana Oil and Gas bringing Water Injection sites up to NEC code, Replacing 250hp Injection motor, switch’s and adding seal-offs and proper grounding where required.

I work daily on PM’s and calibrations of I /P’s and Transmitters, mainly Foxboro and Rosemont on well sites.

I am also in charge of locates, sizing and ordering of materials. I have been designing and wiring chemical pump motor controls for up to 32 wells on a pad. This includes wiring and design of PV Array, solar skids, and ThermoGen skids which consist of 3-120 watt ThermoGen and 1000watt battery banks. This provides enough Amp/Hours to run 8-12vdc chemical pump motors continuously at the rates needed. I have designed and wired complete control panels with Siemens Logo control timers for these that this has been proven in the field. This has also been accomplished with 400 watt Solar Skids with design and wiring and a 1000 amp/hr. battery bank.

I have installed Automation equipment and wiring for well pads with up to 32 wells. This includes the installation of all Transmitters, MSO’s, Sov’s, MVS’s, MDS I net communication, and ROC 809, 503, 107. This also includes a full charging system with Outback controllers and battery bank with disconnects.

Pyramid Instrumentation and Electrical, Grand Junction Co. 10/15/2007-11/23/2011

Supervisor

Electrical/ Instrumentation

Scheduling of up to 28 Electricians and Instrument Technicians

Meet with Clients on proposed projects in the Industrial field

Re; Tri-State Generation {Supervised and assisted with Calibrations and provided documentation of all procedures taken on Transmitters for Unit Outage’s on 3 separate scheduled outages and updates to client of progress on a daily basis.}

Public Service of New Mexico, San Juan Generation {Supervised Calibrations and documentation of Transmitters on Unit Outage on 3 scheduled outages and updates to client of progress}

I have completed day to day projects, and large projects for;

EnCana Oil & Gas, Williams Production, 212 Resources, PDC Energy, American Shale Oil, Shell Oil & Gas, Whiting Oil & Gas, Wagner Equipment, Cray Valley, Black Hills Compression, Delta Petroleum, Gunnison Energy, RJ Taylor, Solvay Chemicals, Energy Transfer Company, Source Gas Company, Antero, Valerus, Kee Engineering

This includes call-outs and call-out scheduling for these clients.

Meet with Clients, Engineers, and State Electrical Inspectors for proper installations on all projects.

I was in responsible for scheduling of man hours for all projects, Job Details, Lawful Electrical Installation, Scheduling of materials, Reading and understanding all P&ID’s, Material Procurement, Client up-dates, Accuracy of Field worksheets, Accuracy of personal timesheets, Assist in all Installations, Personally worked with and installed all systems with voltages, 0-5vdc,4-20ma,12-48vdc, 12-480vac and 5kv installation and testing. Meet with client and state Inspectors.

Submitted to corporate all truck and tool Requisitions for all Employees.

Wil-Tech Automation, Parachute Co. 2005-2007

Manager

Installed and assisted in programming of new communications {MDS} infrastructure for Williams Production RMT.

Installed and assisted in design of 3 major communication repeater sites at the top of Mt. Callahan across to Davis Pt. which was the communications back bone to Piceance Creek from there plant in Parachute. Each site consisted of a 2200w PV Array and back-up Wind Turbines with charge controllers and 5000 watt battery bank. All sites were self-supporting with building and up to 45’communication tower.

I was also responsible for,

Scheduling of Projects with clients

Estimating

Material Procurement

Crew scheduling

Ducey’s Electric Company, Rangely Co. 2001-2005

Worked with ForeRunner Corporation installation and wiring of New NG Compressors and building at Xcel Energy West Rifle Plant. I also worked with them at Double Eagle Compressor Station Naturita Co. adding analog transmitters and wiring throughout the plant, Installations wiring of well pad compressors and Flow Meter skids and communication.

Installed wiring for motors and transmitters at ChevronTexaco process plant in Rangely Co.

I was the main Electrical Contractor at Solvay Chemicals for Large and small scale projects. I was in charge of day to day maintenance at their mining plant and process plant. I worked closely with I&E department installing new transmitters and motors throughout both facilities. I was in charge of disassembling of their CO2 plant at their mining facility and relocating to North Parachute. This included moving of all medium voltage and 480v MCC’s and reassembled at their new location at North Parachute. I also installed new medium voltage Buss Duct and medium voltage mcc sections to existing mcc. Provided technical support on a daily basis. All projects were completed with red-line drawings and submitted to Solvay Chemicals.

Nepple Electric, Alta Iowa 1985-2001

Journeyman Electrician

Provided Electrical Wiring and Control Wiring of Large scale Hog Confinements, Grain Elevators, Residential, and Commercial projects. All projects were design and build. This included overhead lines. I was in charge of all equipment operations involved of completing the Electrical installation, High Ranger Booms, Man Baskets, Backhoes, and Trenching equipment.

Education

Alta Community School Alta, Iowa 1972-1984

Northwestern Iowa Technical College NEC Course 1990

Onan Generator Technical Training Course 1990

TECo Inc. Industrial Electrical NEC update courses 1991

Western Iowa Tech Community College NEC updates and changes 1996

Onan Certified Service Technician Level I & II 1996

Northwestern Iowa Community College Continuing Education NEC updates and changes 1999

Touch Stone Energy Electrical updates 1987-1999

Training for Paramedic, Fire, and Rescue weekly. {Belonged to Alta Fire and Rescue}

OSHA 10 General Industrial Safety and Health 2002

OSHA 10 General Industrial Safety and Health 2005

Certified Medic First Aid {Yearly}

Certified Confined Space Training OSHA 1910.146

Certified H2S Training Course ANSI Z390-1996

Certified NFPA 70E-Arc Flash/LOTO and Electrical Safety 2013

PEC- Safe Gulf/Safe Land USA Training

Equipment Operation Certification on Track hoe, Backhoe, Fork Lift, and Man lift up to 160’

References

Mark Brassette-970-***-****

Rob Gailey-970-***-****

Kyle McCracken-970-***-****

Lenny Vonfeldt- 412-***-****

Alex Mascarenas-719-***-****

Skills

Good work ethics with not only completing projects but completion with pride and integrity.

Good personal skills with clients and employees.

I have provided clients with a product with-in budget and showing good craftsmanship.

I am able to solve Electrical and Technical problems in an efficient and timely manner.

I am very familiar with reading and understanding P&ID’s

I have a known record of my workmanship and dedication to this field.

Contact this candidate