Maintenance Supervisor Engineering Technician
Resume:
Jeffery D. Grochowski
**** ****** ***. ****** **** 43612
*******@*****.***
Objective: Looking to obtain a maintenance management position.
Experience: 07/2015-Present Dana Holding Maumee Oh.
Senior Engineering Technician / Test Lab Machinery Maintenance
Work on and repair all equipment in the test lab, light vehicle and commercial vehicle.
Electrical, Mechanical, Hydraulic and PM repairs to all test lab equipment, including but not limited to rebuilding and replacement of hydraulic linear and rotary actuators with pressure of 3000 psi, HSM, Power Columns are rotating electric storage units, Dynamometers that test differential axles which are a 3 motor drive systems and run off 480 VAC some are 550 VDC. Hydraulic Power Units are up to 6 individual modules in 1 unit that are computer controlled.
Working with 5 S, Safety solutions, LOTO
07/2014-07/2015 Jaytec LLC. Milan Mi.
Maintenance / Tooling Tec
Electrical and mechanical repairs to 3 steel tube mills and 1 roll former also do machining of parts (lathes, mills, surface grinders, band saws, mig, tig and stick welding)
Do rolling setups that consist of changing bearing, cleaning tooling grinding cut off jaws, making or repairing Impeder rods.
Set up a new parts crib
Repair and rebuild gearboxes spur gear boxes which would be a 1:1 drive or reduction gear boxes.
Electrical troubleshooting and repairs to control circuit 24 v & 110 v and high frequency welder with main incoming power of 480 VA Design, Fabricate, assemble and weld roll stands and roll lifting jigs that can lift and balance 2 rolls of 200# ea. for easy loading.
09/2013-06/2014 Severstal NA Dearborn Mi.
Electrical Maintenance Supervisor
Arrange daily work schedules for up to 30 electrical and mechanical employees
Troubleshoot electrical, PLC 5 and RS Logics, photo heat sensors of 115 volt to detect hot slab, lasers, 480 VAC & 500 VDC motors and wiring
Assist in machinery breakdowns and repairs which could be from control wiring of 24 vdc to 115 vac, Hydraulic valves or actuators, or possible bearing break down.
Ordered replacement parts for equipment and machinery
Set up PM’s and MWO
1992-2009 Sterling Pipe and Tube Toledo, OH
Machinery Maintenance Supervisor
Kept steel tubing mill in production and building maintenance
Troubleshoot electrical on mills which are 3 motor DC drives which controls forming, fins and sizing sections. 480 VAC cranes replace cables, shives, replace pendants, repair or replace power bars, repair or replace crane rails. Repaired propane powered forklifts, rebuilt
Gearboxes spur gear and gear reduction boxes, troubleshoot DC or AC motors megger motor, change brushes, replace blower motors, pneumatic valves cylinders main line pressure of 110 psi and hydraulic valves and actuators rebuild and or replace and accumulators pressure up to 1500 psi
Remanufactured machines, built new machines,
Worked on High Frequency Induction welders up to 50,000 VDC main incoming power 480 VAC.
Running conduit and buss way for power to new equipment running chiller water, process water and air lines, which could be 2” blk pipe or PVC or CPVC down to ” pipe.
Set up and performed preventative maintenance on all equipment, Purchasing of most shop supplies, and all maintenance supplies
Scheduling up to 8 employees
Familiar with and followed OSHA guidelines
Work on forced air gas furnaces and radiant heaters and I have some
experience with air conditioning and chiller units.
Took care of all building maintenance and repairs on up to 3 buildings. Hired contractors as needed for building repair or added help for equipment installation.
May 2013 Owens Community College Toledo, OH
Electrical Degree
PLC’s Allen-Bradley, Modicon
Motor Controls, Panel Wiring, NEC
GPA – 3.75
Completed classes in AutoCAD
Member of Owens Honors Program
Microsoft Office
Electrical, controls, AC / DC motors Ladder & Relay logic
PLC Allen Bradley PLC-5, RSLogix, ControlLogix
NEC training
35 yrs. Welding
30 yrs. Machine shop experience
25 yrs. Hydraulic and Pneumatics
Proficient reading blue prints
30hr. OSHA training
ARC Flash training
Experienced forklift driver and mechanic
Facility’s Management
Machine repair
Machine set-ups and changeovers
Maintenance of machinery including knowledge of electrical, pneumatic, hydraulic
And mechanical systems
Order and maintain spare part inventory
Mechanical/Electrical Troubleshooting
Building maintenance
Ability to work with 12 VDC up to 480 VAC 3 phase power
Maintain computerized Preventative Maintenance system
Ergonomic improvements
Contact this candidate