Satellite Technician Installer
Resume:
Robert Howell
Experience
Contact Information
****************@*****.***
Address
S.C. US 29040
Phone
Skills
• Product Testing
• Self-motivated
• Client assessment and analysis
• Strong verbal communication
• Exstremely organized
• Materials preperation
• Hardware evaluation
• Certified fork lift expieriance
Certified SBCA Satellite installer
#301329
•
• Inspection reviews
30+ yrs. experience of thorough, high speed, and high quality multitasking production, of both direct and indirect consumer based products. Including in Manufacturing, In Home installations of electrical based products, and retail electronics sales. machine operator/machine thecnical
training
Sumter Easy Home LLC
Sumter, South Carolina
November-2018
Currently
Roberts Satellite Satellite Technician: Installer/Servicer Installs/Service
Sumter/Lee Counties South
Carolina
September-2017
November-2018
Honda Manufacturing of High/Low pressure finishing South Carolina
Timmonsville, S.C.
July-2015
September-2017
Set up and operation of, die press polymer injection mold.
• Load polymer hoppers with base material.
• Clear injection material bleed off from machinery. Operate die press each quarter of my shift and QA
finished product for any defect or deficiencies.
•
Also, may float position for Packer, Fork Lift
operations, or any man power shortage as needed.
•
Set up and operation of, New recently on line model combination die press polymer injection mold with
conveyance system to rubber mold injection and press for anti slip model product.
Same process as all above for standard die press
polymer injection mold.
•
New system currently operating in partially manual mode requiring hands on removal and press
clearing and set up for each cycle to ensure QA of finished product.
•
Currently being trained by shift manager and lead
tech. for machine start up operation, and how to
resolve any error stops, as well as end of week shut down and machine maintenance.
•
Complete installation of microwave down link
equipment for television/internet satellite receiving equipment, including, but limited to:
Onsite surveys, to determine line of site for dish location placement.
•
Mounting all necessary hardware :i.e. satellite dish, roof, wall, or ground mount hardware.}
•
Route all wiring, applicable inline circuitry, and connect to preexisting on site equipment, including electrical grounding circuits.
•
• Align dish for maximum signal strength.
• Activate all applicable programming/services.
Educate consumer as to all operations and controls of equipment.
•
• Certified SBCA Installer #301329
High/Low pressure finishing, of newly cast aluminum crank cases and cylinder heads, for 4x4 and side by side motor vehicles, directly form dye's.
• High pressure table: Utilized pneumatic and hand Education
Direct Broadcast Services/ Sub-contract: Satellite Technician Radio shack
Sumter/Lee counties South
Carolina
June-1998
February-2015
University of South No degree
tools, to clear excess flashing, gates, and bearing mount apertures, from low speed high pressure
castings of crank cases, to bring parts within
specifications of milling machines.
• Low pressure table: Same as procedure above.
My production average 100+ parts per shift quarter, at a minimum per quarter shift requirement of 75
parts per quarter.
•
Inspected each parts finishing, for casting flaws and failures, for quality control assurance and or scrape failed units.
•
Fork Lift Operator:
Fork lifted parts filled caddies to appropriate
assembly line locations. Or, to built up stock storage stocking.
•
Fork lifted raw aluminum ingots, from receiving
docks, to furnace room, for smelting or storage.
•
Machine Operator:
Set up and operation of industrial Gate Cutter
machine, used to remove gates from two and four
stroke motor cylinder heads.
•
Set up and operation of industrial Extruder machine, used to remove casting sand and silica from two
and four stroke motor cylinder heads.
•
Set up and operation of industrial Shot Blast
machine, used to polish two and four stroke motor
cylinder heads, for final finishing milling machines.
•
Machine Maintenance.
Tear down and rebuild neumatic oil injected
reamers, for High and low pressure flashing tables.
•
Installation of new or rebuilt neumatic cylinder
hammers for the sand extruder machine. and install mounting blocks in same machine per requiered
cylinder head model being run for production.
•
install new industrial cutting blades for cylinder head gate cutting machine.
•
mantain shot levels and discard waste shot dust for industrial shot blast machine.
•
replace and or clean any and all machine oil level requirments and air filtration systems.
•
R and R fork lift forks for proper size forks needed, exchange fuel cylinders as needed.
•
Same as all responsibilities. procedures, Skills, and Certifications, I currently perform as an SBCA
certified technician currently.
•
Completed 15 credit hours of 26 hour Business
Carolina @ Sumter
Sumter, South Carolina
Sumter High School High School Deploma
Sumter, S.C.
1980
Administration Associates degree.
Additionally:
Completed the SCWRC Work Keys testing program on
06/03/2015, tests and scores as follows.
Applied Mathematics Test: Scored a level 6 of a
possible range 3 to 7 which is equivalent to a scale score 82 of a possible range 65 to 90.
•
Reading for Information Test: Scored a 6 of range 3 to 7 equal to scale 82 of range 65 to 90.
•
Observation Test: Scored a 5 of range 3 to 6 no 0 - 100 scale provision offered.
•
Locating Information Test: Scored a 4 of range 3 to 6 equal to scale 76 of range 65 to 90.
•
Qualified for National Career Readiness Certificate.
Contact this candidate