Welding Inspector Steel Bridge
Resume:
October **** – Present
TPCA INSPECTOR on Behalf BV Singapore
Project: Galfar, EPIC For CO2 water Alternating Gas (WAG) Injection Pilot Project At Dukhan
Location : PT Cladtek BI Metal Manufacturing - Indonesia
Duties & Responsibilities:
Design, develop and implement best quality practices and processes for product developments.
Maintain, monitor and ensure highest quality in services or products.
Develop and initiate quality standards for tests, inspections and evaluations.
Design and develop forms and instructions for evaluating, assessing, reporting and documenting on quality standards in products or services.
Witness Inconel 625 weld Clad Material, Check Welding Parameter refer to Approved WPS, Check Consumable, WO Qualification, and Calibration of Equipment.
Monitoring and Witness process of Bend Pipe following of procedure of work and Instruction sheet. Check Visual of Cladding Before bending.
Check Visual and Dimensional after Bending refer to Drawing and Spec Requirement.
Verifies joint configuration against approved drawings.
Verifies welding parameters are conformance to approved WPS
Witness Inspection Activity: Final Dimensional Control, Residual Magnetism Check, MPQT & Production Test, Final Visual Inspection.
Review Document and Report Inspection
April 2021 – October 2021
QA/QC Coordinator at PT LKS
Project: Prosperity Project
Location : Batam - Indonesia
Duties & Responsibilities:
Check documents/procedures: Approved ITP, approved WPS, approved cutting plan/ Drawing, etc
Should be able to assign QC personnel from receiving/verification materials till process of welding and other activities such as qualification.
Ensure QC coverage at site is sufficient for both night and day shift activities also.
Ensure all QC personnel are fully aware regarding HSE requirements.
Ensure all approved procedures to be implemented at site.
Ensure enough QC’s Inspection tool for inspection purpose at site.
Coordinating with NDT coordinator regarding NDT issue and ensure all NDT reports are submitted to QC Documentation for updated NDT status.
Coordinating with welding engineer regarding any welding issue.
Coordinating with Project Coordinator regarding cutting plan/drawing, schedule, etc
Coordinating with client and third party regarding inspection activities as stated in approved ITP.
Preparing shipment for all project.
Control and execute Production lot test related with Destructive Testing matters ( Mechanical and Laboratory Test ) suitable with relevant code, ITP or client specs requirement.
Reviewed and verified Fabrication/Manufacturing Procedure, WPS, Fabrication Drawing, NDE Map, Mill Certificates, Non Destructive Testing Procedure (MPI, PT, UT and RT).
November 2020 – March 2021
TPCA INSPECTOR on Behalf TUV Rheinland Indonesia
Project: HESS NMB Phase 3
Location : PT Cladtek BI Metal Manufacturing - Indonesia
Duties & Responsibilities:
Design, develop and implement best quality practices and processes for product developments.
Maintain, monitor and ensure highest quality in services or products.
Develop and initiate quality standards for tests, inspections and evaluations.
Design and develop forms and instructions for evaluating, assessing, reporting and documenting on quality standards in products or services.
Witness Inconel 625 weld Clad Material, Check Welding Parameter refer to Approved WPS, Check Consumable, WO Qualification, and Calibration of Equipment.
Monitoring and Witness process of Bend Pipe following of procedure of work and Instruction sheet. Check Visual of Cladding Before bending.
Check Visual and Dimensional after Bending refer to Drawing and Spec Requirement.
Verifies joint configuration against approved drawings.
Verifies welding parameters are conformance to approved WPS
Witness Inspection Activity: Final Dimensional Control, Residual Magnetism Check, MPQT & Production Test, Final Visual Inspection.
Review Document and Report Inspection
July 2019 – September 2020
QC Engineer PT Singatac Bintan
Project: Merakes Development Project
Location : PT Singatac Bintan - Indonesia
Duties & Responsibilities:
Design, develop and implement best quality practices and processes for product developments.
Maintain, monitor and ensure highest quality in services or products.
Develop and initiate quality standards for tests, inspections and evaluations.
Design and develop forms and instructions for evaluating, assessing, reporting and documenting on quality standards in products or services.
Develop strategies to evaluate precision and accuracy of analytical equipment, tests & measurements and production equipment.
Troubleshoot and resolve problems relating to quality control aspects.
Lead, direct and assist technical, professional staff n measuring and testing a product or a service.
Tabulate and document data relating to products, processes, materials, its qualities and reliabilities.
Research, study, compile and prepare material on quality control activities, processes and procedures.
Train staff, technicians and professionals on the aspects of quality control activities.
March 2016 – March 2018
QA/QC Representative Sembcorp Marine Pte Ltd
Project: Total Kaombo FPSO South / North
Location : PT Singatac Bintan - Indonesia
Duties & Responsibilities:
Checks availability of welding procedures specifications.
Checks qualification of welders and welding operators.
Verifies joint configuration against approved drawings.
Verifies welding parameters are conformance to approved WPS.
Checks fit-up of sub-assembly and assembly of structures.
Performs daily in-process inspections.
Verifies welding consumable handling and storage.
Provides guidance to production supervisor on quality matters-to coordinates the NDE activities with the production supervisors.
Witnesses all test, such as hydrostatic, pneumatic and leak test.
Performs visual and dimensional inspection with client's inspectors.
Collects inspection data's for generating of manufacturing books
Ensure the safety of personnel through compliance with Occupational Safety and Health and Environmental Regulations.
Ensure that Health, Safety & Environmental operating procedures are followed and counsel employees about compliance as necessary.
Participate in the preparation of Safe work, Environmental control and Emergency procedures.
Ensure that all Health, Safety, Environmental & Quality (HSEQ) plans are followed.
January 2016 – March 2016
QA/QC Coordinator at PT Wasco Engineering Indonesia
Project: Total Kaombo
Location : Batam - Indonesia
Duties & Responsibilities:
Check documents/procedures: Approved ITP, approved WPS, approved cutting plan/ Drawing, etc
Should be able to assign QC personnel from receiving/verification materials till process of welding and other activities such as qualification.
Ensure QC coverage at site is sufficient for both night and day shift activities also.
Ensure all QC personnel are fully aware regarding HSE requirements.
Ensure all approved procedures to be implemented at site.
Ensure enough QC’s Inspection tool for inspection purpose at site.
Coordinating with NDT coordinator regarding NDT issue and ensure all NDT reports are submitted to QC Documentation for updated NDT status.
Coordinating with welding engineer regarding any welding issue.
Coordinating with Project Coordinator regarding cutting plan/drawing, schedule, etc
Coordinating with client and third party regarding inspection activities as stated in approved ITP.
Preparing shipment for all project.
Control and execute Production lot test related with Destructive Testing matters ( Mechanical and Laboratory Test ) suitable with relevant code, ITP or client specs requirement.
Reviewed and verified Fabrication/Manufacturing Procedure, WPS, Fabrication Drawing, NDE Map, Mill Certificates, Non Destructive Testing Procedure (MPI, PT, UT and RT).
May 2015 – 31 December 2015
QC / Structural Inspector at Sapura Kencana Petroleum Berhad.
Project: ISBL Wheatstone project LNG plant Bechtel
Location : Lumut, Perak – Malaysia
Duties & Responsibilities:
Inspect of Material such as Plate, Pipe and associated and Check to Mill Certificate (Type, Head Number, Mechanical Properties, Chemical Composition, Size), Dimensional, Straightness, Pitted and etc. Issue Material Receiving Report and Approval to Client.
Witness during Cutting material base on Cutting Plan drawing.
Monitoring Fabrication following AFC, Shop Drawing and Weld Map.
Review Contractor Procedure such as : Material Handling, Fabrication, NDT Procedure, Document Control, Safety, etc.
Check and Monitoring (Before Welding) ; Welding Preparation base on WPS ; root gap, root face, beveling, dimensional, cleaning, pre-heating, electrode storage and size. (During Welding: Inter pass Cleaning, Welding Sequences, Inter pass Temperature, Welding Parameter (Voltage, Ampere, Travel Speed, Heat Input) and Environmental. (After Welding: Finishing, Cleaning, Grinding and repair.)
Conduct and Witness during Cutting, Fit-up and Visual Inspection during Fabrication Sequences in Assembly, Erection and Final Inspection.
Control and Monitoring of QA/QC Subcontractor are properly work & implemented of ITP and Procedure.
Control and Monitoring of Welder, Fitter and Helper are properly work & implemented of WPS and Fabrication Procedure.
Coordination with Client and related Department and Contractor about planning, progress, problem and solving of projects.
Witness during Non-Destructive Testing (NDT-MPI/DPI and UT), Blasting, Painting, Weighing, Ballast, Drain mat and HDPE Installation.
Make Daily, Weekly, Monthly Report and Problem Solving.
Prepare Manufacturing Data Record (MDR) such as MRR, MTR, Fit-up, Visual Inspection, NDT, Welding Summary Report and others quality record.
Check valid Calibration of All Equipment and Measurement Gauges.
Witness of Welder Test.
Conduct Daily Safety Tool Box meeting and Support of Safety Program.
May 2014 – April 2015
QA/QC Inspector at PT. McConnell Dowell Service.
Project: Wheatstone project LNG plant Bechtel
Location : Batam - Indonesia
Duties & Responsibilities:
Inspect of Material such as Plate, Pipe and associated and Check to Mill Certificate (Type, Head Number, Mechanical Properties, Chemical Composition, Size), Dimensional, Straightness, Pitted and etc. Issue Material Receiving Report and Approval to Client.
Witness during Cutting material base on Cutting Plan drawing.
Monitoring Fabrication following AFC, Shop Drawing and Weld Map.
Review Contractor Procedure such as : Material Handling, Fabrication, NDT Procedure, Document Control, Safety, etc.
Check and Monitoring (Before Welding) ; Welding Preparation base on WPS ; root gap, root face, beveling, dimensional, cleaning, pre-heating, electrode storage and size. (During Welding: Inter pass Cleaning, Welding Sequences, Inter pass Temperature, Welding Parameter (Voltage, Ampere, Travel Speed, Heat Input) and Environmental. (After Welding: Finishing, Cleaning, Grinding and repair.)
Conduct and Witness during Cutting, Fit-up and Visual Inspection during Fabrication Sequences in Assembly, Erection and Final Inspection.
Control and Monitoring of QA/QC Subcontractor are properly work & implemented of ITP and Procedure.
Control and Monitoring of Welder, Fitter and Helper are properly work & implemented of WPS and Fabrication Procedure.
Coordination with Client and related Department and Contractor about planning, progress, problem and solving of projects.
Witness during Non-Destructive Testing (NDT-MPI/DPI and UT), Blasting, Painting, Weighing, Ballast, Drain mat and HDPE Installation.
Make Daily, Weekly, Monthly Report and Problem Solving.
Prepare Manufacturing Data Record (MDR) such as MRR, MTR, Fit-up, Visual Inspection, NDT, Welding Summary Report and others quality record.
Check valid Calibration of All Equipment and Measurement Gauges.
Witness of Welder Test.
Conduct Daily Safety Tool Box meeting and Support of Safety Program.
April 2012 – May 2014
QC Inspector at PT. Cladtek BI Metal Indonesia
Projects:
> Liwan Deep Water ( Husky Oil China )
> Gorgon ( GE Sandvika )
> Saudi Aramco ( Aramco Overseas Company )
> Shah Gas ( Samsung Engineering )
> Barzan ( Hyundai Heavy Industries )
Location : Batam - Indonesia
Duties & Responsibilities :
Prepare and Review some procedure base on Client Specification and or Code Standard References.
Review Design Engineering (Isometric Drawing, as build Drawing, Equipment, Material before execution to Production.
Monitor Fabrication Quality, Progress, Sequence and Installation of Piping and Equipment as per Drawing and specification.
Conduct witness Inspection activities and testing with Client and Third party (Such as; Material Inspection, Cutting, Fit/up, Visual, NDE, Load test, Hydro test, Weighing, etc.).
Make the Report of Material Traceability, Fit-up and Visual Report to complete of Test Pack.
Conduct Line Work, Re-instatement and Mechanical Completion the Test Packages follow the Line Services P&ID and Isometric drawing, NDT status, Weld summary, Hydro test for Piping.
Manage and Monitor all QC Inspection activities (Piping, Structure, NDT, Painting/Blasting and Document Control.
Coordinate with relevant Department, Subcontractor, supplier, vendor, Third party and Client of any quality issued and problem solving.
Direct Reporting and support Quality Improvement to QC Manager and Project Manager.
Expedite of any backlog progress on site to Production related with QC activities and responsibilities.
Capture, analyze and re-improvement of quality method, process flow and communication lines
Monitoring welder performance during welding and control repair rate under the target.
Support to running PQR/WPS Qualification, Mechanical Testing and Welder Qualification Test.
Review Welding Sequence of Fabrication and NDE Mapping (WPS used and NDT Requirement).
December 2009 – February 2012
QA/QC Inspector at PT. Nippon Steel Batam.
Project : Gajah Baru Premiere Oil, Total South Mahakam
Location : Batam - Indonesia
Duties & Responsibilities:
Inspect of Material such as Plate, Pipe and associated and Check to Mill Certificate (Type, Head Number, Mechanical Properties, Chemical Composition, Size), Dimensional, Straightness, Pitted and etc. Issue Material Receiving Report and Approval to Client.
Witness during Cutting material base on Cutting Plan drawing.
Monitoring Fabrication following AFC, Shop Drawing and Weld Map.
Review Contractor Procedure such as : Material Handling, Fabrication, NDT Procedure, Document Control, Safety, etc.
Check and Monitoring (Before Welding) ; Welding Preparation base on WPS ; root gap, root face, beveling, dimensional, cleaning, pre-heating, electrode storage and size. (During Welding: Inter pass Cleaning, Welding Sequences, Inter pass Temperature, Welding Parameter (Voltage, Ampere, Travel Speed, Heat Input) and Environmental. (After Welding: Finishing, Cleaning, Grinding and repair.)
Conduct and Witness during Cutting, Fit-up and Visual Inspection during Fabrication Sequences in Assembly, Erection and Final Inspection.
Control and Monitoring of QA/QC Subcontractor are properly work & implemented of ITP and Procedure.
Control and Monitoring of Welder, Fitter and Helper are properly work & implemented of WPS and Fabrication Procedure.
Coordination with Client and related Department and Contractor about planning, progress, problem and solving of projects.
Witness during Non-Destructive Testing (NDT-MPI/DPI and UT), Blasting, Painting, Weighing, Ballast, Drain mat and HDPE Installation.
Make Daily, Weekly, Monthly Report and Problem Solving.
Prepare Manufacturing Data Record (MDR) such as MRR, MTR, Fit-up, Visual Inspection, NDT, Welding Summary Report and others quality record.
Check valid Calibration of All Equipment and Measurement Gauges.
Witness of Welder Test.
August 2009 – December 2009
Welder FCAW SS 6GR at PT McDermott Indonesia
Project : Maersk Oil
Location : Batam – Indonesia
April 2008 – June 2009
Welder FCAW GS 3G/4G & Robotic Welding at Nippon Steel Bridge Co.Ltd
Project : Haneda
Location : Wakamatsu - Japan
June 2007 – April 2008
Welder SMAW 6G at PT Nippon Steel Batam
Project : Total
Location : Batam – Indonesia
March 2007 – June 2007
Welder 6G/6GR at PT SMOE Indonesia
Project : Blue Water
Location : Batam – Indonesia
Augustus 2006 – February 2007
Welder SMAW 6G at PT Nippon Steel Batam
Project : Total Sisi Nubi
Location : Batam – Indonesia
January 2006 – Augustus 2006
Welder 6GR at PT SMOE Indonesia
Project : Bohai Phase 2 Conoco Philips
Location : Batam – Indonesia
Augustus 2001 – December 2005
Welder SMAW at PT Nanindah Mutiara Shipyard
Project : Ship Building & Repair
Location : Batam - Indonesia
FARID HARDI
Certified Welding Inspector CSWIP 3.1(U.K) Welding Inspector MIGAS (Indonesia Oil & Gas)
Radiography interpreter (NDT Level 2) Penetrant Test (NDT Level 2)
Magnetic Particle Test (NDT Level 2) Ultra Sonic Test (NDT Level 2)
CQI-IRCA Certified ISO 9001:20015 Auditor/Lead Auditor
CURRICULUM VITAE
More than 20 years’ experience in fabrication and 10 years experiences with in Quality Inspection, Welding Inspector mostly Piping, Mechanical in Steel Fabrication, Production and Construction of Oil & Gas Company, Onshore Pipelines, Marine Shipbuilding, Piping Process Petrochemical and Structural Fabrication.
Photoshop
Ms Powerpoint
Microsoft Excel
Microsoft Word
● Self Motivated
● Excellent Leadership
● Problem Solver & Analysis
● Able to Work In a Team
Welding Inspector CSWIP 3.1, (U.K)
Cert No 84404/2 exp date: 02-02-2024
Welding Inspector MIGAS (Indonesia Oil & Gas)
Cert no 03.0011187
Welding Inspector MIGAS (Indonesia Oil & Gas)
Cert no OTI.WI-III.0111.042
Radiography Interpreter (NDT level 2 SNT-TC-1A-2016)
Cert no OTI.RI-XVI.02.18.196
Penetrant Test (NDT level 2 SNT-TC-1A-2016)
Cert no OTI.PT-XXXII.03.18.267
Magnetic Particle Test (NDT level 2 SNT-TC-1A-2016)
Cert no OTI.MT-XXXII.03.18.267
Ultra Sonic Test (NDT level 2 SNT-TC-1A-2016)
Cert no 61/UT/NC/21
CQI-IRCA Certified ISO 9001:2015 Auditor/Lead Auditor (QMS)
Cert On Progress
CQI-IRCA Certified ISO 9001:20015 Auditor/Lead Auditor (Quality Management System)
1997-1999
Politechnic Andalas University – Civil Engineering ( Not Finish )
1994-1997
Senior High School SMU 2 Padang – Sains
1991-1994
Junior High School SMP 24 Padang.
1985-1991
SD 37 Padang
Strong Leadership, Self-starter, highly motivated, dynamic individual, creative, fully of ideas and intention toward improvements, capable to work independently and as a team either, easily to communicate among all levels of people Good team player and multitasking capabilities.
Good Technical background for Establish, Maintain of Quality Management System, Problem Solving, Supervising, Corrective and Preventive Action.
Familiar with Quality Audit, Environmental Audit, Safety Audit, Reporting & Doc. Control.
I am fluent in English and Good Communication skill.
I am willing to work overseas and travelling overseas.
AWS D1.1, ASME II, ASME V, ASME VIII, ASME IX, ASME B31.3, API-1104, API-650/653, API-570, AS.2885.2, DNV.OS-101. Etc.
ITP, WPS, Welder Test, Mech. Test, NDT, MDR, Test Packages, Procedure, Client Specification.
LinkedIn Indonesia
adpyyr@r.postjobfree.com
I confirm that all of information’s in my resume are true and can be accounted.
Best Regards
Farid_Hardi
Contact this candidate