Welder

CHARLES E. WILLIAMS JR.

**** *** **, ********, **. 92346 909·723·6963 ·adpqqd@r.postjobfree.com

OBJECTIVE

Seeking a welding/fitter/Iron worker position where my extensive experience can contribute to your customers' satisfaction and your company's success.

Work Experience:

Ironworker/Welder December 2017 to Present

Able Iron works - Pomona, CA

*Rigging / setting/ welding stair stringers while erecting storage units.

*Connecting/bolting/snapping bolts.

*Handrail fabrication/layout /welding, cutting and grinding.

* Drilling /epoxy holes for wall plates with connection clips to hang stairs.

* Proficient in running operating settling an oxygen set up for torching.

*Certified NR 232 welder

*Certification in welding rebar with stick.

*Certified to operate: Reach-lift, scissor-lift, gradall, boom-lift.

*Certified in :fall protection

*Read blue prints

GBW Railcar Services December 2016- 2017

Railcar repairman

The essential duties and responsibilities as a railroad repairman were:

*Interpreted job work orders to perform required repairs

*Coordinated and completed repairs in an efficient manner and within assigned amount hours

* Notified supervisor of any material and/or

equipment required to ensure completion of job tasks

*Interacted with crew members in a team environment, as well as with the supervisor

*Followed all safety rules,while keeping work area clean and complying with all GBW environmental health and safety policies

Hirschfeld Steel January 2013 - June 2015

Flux Core welder

Welding structural beams of various sizes with 5.64 flux core wire according to the welding procedure on blueprint. The type welds range from 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", up to 2 1/8" and some of the structural beams or plates call for CJP (Complete Joint Penetration) weld. Depending on the thickness of the metal; most beams requires preheating up to 250ºF using a temp stick. After welding procedure is finished the welds are cleaned by grinding BB's from the heel/toe of welds with a scraper or a 4"grinder.

Fitter

Fabricating structural beams according to the blueprint which consisted of:

*Reading tape measure and laying out plates

*Calculating angles, slopes, running dimensions

*trimming/ cutting metal with a torch

* tacking, welding, grinding

*writing weld symbols

Smith Pipe & SPA August 2009 - August 2012

stick/mig welder

I worked as a crew leader fabricating oil tank bottoms that held from 210, 300, 400, 500 barrels of oil in size. This included: measuring, using a cutting torch, fitting couplings / door, and welding with 5p or Jet rod. I also, skillfully Mig welded on pressure vessels for this employer. When welding on the heads of the vessel it required a MIG root and stick all the way out using 7018 jet rods. Often times, I had to build my own parts prior to vessel fabrication.

Frontier Welded Products April 2006 - July 2008

Entry level welder

Grinding, tacking, welding, and operating overhead cranes etc. All of these duties had to be performed in the final stage of constructing a high pressure boiler. In the final stage I was a part of a crew who welded the frame out with Mig, setting the roof panels, tacked on nails for installation, put in installation, screwed on lagging, and welded boiler down to the railroad cart for shipping.

Lauren Engineer Company July 2005 - April 2006

Entry level welder

Grinding, welding, and operating cranes. I was enrolled in welding class provided by the employer. Within the class we practiced tig welding on schedule 40 pipe beveled in a 6g position. The class practiced welding a tig root and filling bevel with 6010.

Skills:

Mig welding; able to pass 1G, 2G, 3G, and 4g test

Flux Core welding; able to pass 1G, 2G, 3G, and4g

Stick welding; able to pass 1G, 2G, 3G, and 4G test

Able to operate cutting torch, overhead crane, and able to gauge.

Able to read blueprints,

Able to read weld type symbols

Academic Certifications & Education:

Junior, Exercise Science and Health, Present

Abilene Christian University

Associates of Arts, General Education, 2001

San Bernardino Valley

entry-level, welder, 2006

Cisco Junior College

flux-core welding 1G, 2G,,3G 2005

I am certified in fluxcore 0.45 wire and 5.64 wire.

Contact this candidate