Exxon Mobil Facilities Engineer

PROFESSIONAL RESUME

of

TEODULO AYCO MAGDOZA

Singapore Address:

*** ***** *** ***** * #03-384

Singapore 510631

Philippines Address:

Lot 55/56 Phase II Camella Homes Subdivision

Lawaan, Talisay City, Cebu Philippines. 6045.

MOBILE PHONE : +65 9223-0295

EMAIL : ********@*****.***

SINGAPORE PR : IC No. S2712414C

PASSPORT NO. : P7903685A

PLACE OF BIRTH : Antequera, Bohol Philippines

NATIONALITY : Filipino (Singapore Permanent Residence)

RELIGION : Roman Catholic

Profile :

An accomplished, versatile and results-driven professional with a proven track record in driving technical skills

and increasing output, ultimately benefiting the company bottom line.

Objective :

Now looking to secure a challenging and rewarding new role within the Electrical / Instrument / Fire & Gas/

Telecoms Engineering industry, where skills, knowledge and expertise gained throughout previous experience

in the Construction, Inspections, Mechanical Completion and Commissioning, Facilities Maintenance Services

both in Commercial Buildings and Oil & Gas field sector, can be transferred across and utilized to best effect

for the benefit of your organization.

Key Competencies :

Construction/Installation

QA/QC Inspection

Mechanical Completion (MC)

Safety Coordinator

Pre-com/Hock-up & Commissioning

Facilities Servicing & Maintenance DATA CENTRE

SUMARY OF QUALIFICATION:

A total of 30 years of active work experiences in the field of Electrical, Instrument and Telecoms Engineering Systems involving design, estimation, supervision implementation, installation, E&I QA/QC Inspection and maintenance.

Also with extensive exposure in the areas of installation, mounting, inspection, operation and maintenance of Mechanical & Electrical/Instrument system covering Voltage up to 22 KV and below 100v to Power Substation, Distribution lines, Power Generators, Switch Gears, Motors and Controllers, Load Center, HMI, DCS, LAN/WAN, Telephone and Security Card Access System, CCTV System and Fire Alarm System, VSAT,(PA/GA),& TVRO.

Also with strong experience in the Air Conditioning and Mechanical Ventilation System (CRAC-UNITS, HVAC,

AHU, RCU, FCU, Chiller and Cooling Tower, Cold Room, Walkin-Freezer/Chiller) Fire Protection System and

Boilers, DRUPS in DATA CENTRE

EDUCATIONALBACKGROUND:

1985-1989: University of Bohol (Philippines)

Bachelor of Science Degree in Electrical Engineering

License Electrical Engineer of the Philippines

1984-1985 : Peoples Electronics Servicing

Electronics Vocational Course (Basic Electronics)

SEMINARS/WORKSHOP:

Mar 07, 2015 :Apply Workplace Safety And Health in Process Plant (EVER SAFE Consultants)

Jan 07, 2013 :Travel Safety By Boat OPITO (SMTC GLOBAL)

Mar 26, 2009 :Safety Orientation Course Oil/Petrochemical (NTUC Singapore)

Oct 12, 2007 :Shipyard Supervisors Safety Course (NTUC Singapore)

May 06, 2006 :Shipyard Safety Instruction Course (NTUC Singapore)

Oct 07, 2004 :Module 3 Communicating for the Knowledge Economy: Speaking & Listening (British Council)

Jul 12,13 2000 : Productivity Management Course (NTUC Singapore)

Oct 22, 1994 :Medium Voltage Switchgears/Substation for Commercial & Industrial Plants Seminar

Jul 02, 1994 :Fundamentals of Illumination Design for Commercial & Industrial Buildings (IIEE Phils.)

Mar 27, 1993 :Technical Seminar on Ind. Motor Controllers Basic & Hi-Tech (IIEE Phils.)

TRAININGS:

07/01/13 to 09/01/13 :Basic Offshore Safety Induction & Emergency Training with HUET EBS OPITO (SMTC GLOBAL)

07/10/12 to 10/10/12 :SEAMAN'S RECORD BOOK AND CERTIFICATES OF DISCHARGE

(MPA Seafarers Management Department Singapore)

28/04/05 to 29/04/05 :Customized Fire Fighting & Breathing Apparatus Course

(Singapore Aviation Academy)

10/02/04 to 16/02/04 :Metal Scaffold Erection (Building & Construction Authority, Singapore)

05/0796 to 27/09/96 :Air-conditioning Technician Training Program (Utopia-Aire Singapore)

04/05/89 to 05/06/89 :Advance Summer Camp Training (MS-43) CL 89,Cebu,Philippines

SPECIAL SKILL:

Hands-On on Personal Computer, Laptop Installation, Repair Both Hardware & Software

Basic Knowledge in AUTOCAD

PROFESSIONAL EXPERIENCE:

July 2021 to August 2021

NES GLOBAL Pte Ltd (NES Fircroft)

Position: Instrument Commission Senior Tech

JOB DESCRIPTION : MODEC FPSO MIAMTE MV34 Project Keppel Benoi Shipyard, Singapore

Site execution of pre-commissioning, commissioning and function testing of instrument system panels,

field instrument panels, field instrumentation, F&G devices, etc.

Working experience of testing Cause & effect and Process Logic from HMI / ICSS.

Working experience for the Package on High- and Low-Pressure Gas Compressor, & Fuel Gas Compressor.

Filling up of ITR’s in online system using iPAD.

Prepare & submit Permit to work online system.

Carry out isolations / de-isolations on instrument equipment and Electrcal devices.

Conduct / attend daily Tool Box Talks to ensure full understanding of work scope as per PTW

requirements.

Ensure that commissioning testing activities are conducted safely and complies with the site PTW

and safety regulations and procedures.

Liaise with vendors for providing assistance in carrying out pre-commissioning and commissioning

scope of work related to vendor packages.

Carry out troubleshooting of faults arising during commissioning tests.

Completing & submission of commissioning documentation such as check sheets, test procedures,

red-line mark-up drawings, etc. completed during commissioning tests.

May 2021 to June

BEST EQUIPMENT XERVICES

Position: Maintenace & Service Engineer

JOB DESCRIPTION:

Support any technical problems at the production and after-sales

Servicing and maintenance of all Chillers, Freezers, Cold Rooms, Walk-in Freezers, Walk-in Chillers,

Combi-Oven, Boilers, various types of Electric & Gas Burner and mode of operation

Servicing of all Analytical Instruments, General Scientific, Petrochemical Equipments, Pharmaceutical &

Medical Equipments, Safety Instruments, Construction Monitoring Instruments.

Installation, Testing & Commissioning of All Equipments

August 2016 to April 2021

ACME ASSOCIATES PTE LTD

CRAC UNITS Replacement Project at Singapore Prison Service

Position: Project & Facilities Engineer (DATA CENTRE)

JOB DESCRIPTION PROJECTS & MAINTENANCE

On-site contractors and human resource management

Project planning, methodology, reviews and baseline controls

Schedule planning and follow-up project status

Procurement management in identifying budget constraints, lead-time

Adhering to quality goals in project execution

Ensure proper communications and information flow internally and externally

Reference design criteria to infrastructure build-up and equipment set up

Work through a pre-established testing & commissioning specifications

Scan through every level of equipment, especially in critical areas like electrical and mechanical

The Facilities Management programme includes :

On-site facilities engineer, as required by the client

Proactive checks on environment and equipment, such as

the electrical and mechanical systems used in a data center environment,

DRUPS, Transformers, Generators, Switchgear, UPS systems, ATS/STS units,

PDUs, Chillers, AHUs and PAC or CRAC units.·

Swift preliminary analysis during emergency

Single point of contact between service provider and partners

Regular report updates and recommendations on site conditions

The Project Management Process Includes:

On-site contractors and human resource management

Project planning, methodology, reviews and baseline controls

Schedule planning and follow-up project status

Procurement management in identifying budget constraints, lead-time

Adhering to quality goals in project execution

Ensure proper communications and information flow internally and externally

July 2015 to July 2016

BEST EQUIPMENT XERVICES

Position: Maintenace & Service Engineer

JOB DESCRIPTION:

Support any technical problems at the production and after-sales

Servicing and maintenance of all Chillers, Freezers, Cold Rooms, Walk-in Freezers, Walk-in Chillers,

Combi-Oven, Boilers, various types of Electric & Gas Burner and mode of operation

Servicing of all Analytical Instruments, General Scientific, Petrochemical Equipments, Pharmaceutical &

Medical Equipments, Safety Instruments, Construction Monitoring Instruments.

Installation, Testing & Commissioning of All Equipments

February 2015 to June 2015

PAN GREATWAYS ENGINEERING PTE LTD

Position: E&I Commission Senior Tech

JOB DESCRIPTION : SETE BRAZIL Drilling Project Keppel Fels Shipyard, Singapore

Site execution of pre-commissioning, commissioning and function testing of instrument system panels,

field instrument panels, field instrumentation, F&G devices, etc.

Working experience of testing Cause & effect and Process Logic from HMI / ICSS.

Filling up of ITR’s in online system using iPAD.

Prepare & submit Permit to work online system.

Carry out isolations / de-isolations on instrument equipment and Electrcal devices.

Conduct / attend daily Tool Box Talks to ensure full understanding of work scope as per PTW

requirements.

Site management of commissioning activities, tools, ship-loose items, consumables and spares.

Ensure that commissioning testing activities are conducted safely and complies with the site PTW

and safety regulations and procedures.

Liaise with vendors for providing assistance in carrying out pre-commissioning and commissioning

scope of work related to vendor packages.

Carry out troubleshooting of faults arising during commissioning tests.

Completing & submission of commissioning documentation such as check sheets, test procedures,

red-line mark-up drawings, etc. completed during commissioning tests.

Close out of punch list.

Attend Site acceptance tests (SAT).

Prepare Tri-party walk work pack as per the required format.

Attend Tri-party punch walk as required by supervisor.

To attend daily VSCC / Permit To Work meetings as advised by supervisor.

Maintain latest drawings / documentation on site including all red-line markup drawings.

Preparation of daily timesheet submissions.

Adherence to commissioning schedule.

April 2014 to December 2014

BRUNEL INTERNATIONAL S.E.A. PTE LTD

RATU NUSANTARA FPSO (M3NERGY) Project - : Keppel Benoi Shipyard, Singapore

POSITION : E&I Commissioning Supervisor (Mechanical Completion & Commissioning)

JOB DESCRIPTION

Supervised & performed Mechanical Completion scope of works.

Supervised & performed line & resistance check for all electrical, instrument cables both for power

cable, control cable and antennas cable.

Supervise and performed installation and testing of relay and PLC based safety shut down systems

including, OMRON, SIEMENS.

Supervised & performed testing and commissioning of DCS and Communication Systems.

Supervised & performed testing & commissioning of Process Control Systems for liquid and gaseous

fuels, combustion air and feed water or process flow.

Supervised & carry out hot loop check & testing for Process Instrumentation; E&I Systems, Fire &

Gas System.

Preparation of Electrical & Instrument inspection test record (ITR’S) as per specification.

Study and review vendors drawings documents and ensure implementation in compliance with

specifications.

Conduct Electrical and Instrument inspection in the installation, modification and fabrication done by

contractors.

Prepare site inquiries for Electrical & Instrument fabrication installation and issues within the contractors.

Prepares project work schedules progress monitoring and daily/ weekly progress report.

Attend safety meetings with various disciplines for Permit to Work discussion.

Able to guide and lead a team of in house work force & contractors.

August 2013 to March 2014

PACIFIC ORIENTAL PTE LTD

TELOK B & DAMAR A PLATFORM EXXON MOBIL Project - : Malaysia (Offshore)

POSITION :E&I Commissioning Engr.

JOB DESCRIPTION

Supervised the testing, simulation of motor interfacing at HMI and DCS such as motor status signal,

start stop command, manual/auto status, and PSD interlock. Simulation and cause and effect testing

of all emergency and shutdown devices.

Supervised & performed Mechanical Completion & Carry over scope of works.

Supervised & carry out hot loop check & testing for E&I System Supervised Pre-Com & commissioning

of E&I System (FM200, F&G, HVAC, RMU 13.8KV Switchgear) Pressure/Level/Flow Transmitters.

Calibration, simulation, troubleshooting, of all process instruments used to measure, monitor records

and controls different process variables such as flow, pressure, level, temperature and others.

Testing & Commissioning of combustion in boilers, fired heaters and flares.

Supervised the punch list clearing & prepare ITR/Check Sheet for client approval.

Preparation of all required systems for the start-up of Well Heads.

Support of the operation for start-up of the two Well Heads (A10 & A16)

May 2013 to August 2013

BRUNEL INTERNATIONAL S.E.A. PTE LTD

FPSO N'GOMA SBM Project - : Keppel Tuas Shipyard, Singapore

POSITION : E&I and Telecoms Commissioning Supervisor (Mechanical Completion & Commissioning)

JOB DESCRIPTION

Supervised & performed Mechanical Completion scope of works.

Supervised & performed line & resistance check for all electrical, instrument & telecoms cables both for

power cable, control cable and antennas cable.

Preparation of Electrical & Instruments inspection test record (ITR’S) as per specification.

Study and review vendors drawings documents and ensure implementation in compliance with

specifications.

Conduct E&I and Telecoms inspection in the installation, modification and fabrication done by

contractors.

Prepare site inquiries for Electrical/Instrument/Telecoms fabrication installation and issues within the

contractors.

Prepares project work schedules progress monitoring and daily/ weekly progress report.

Attend safety meetings with various disciplines for Permit to Work discussion.

Conduct regular performance tests of unit process equipment to identify actual performance and

provide follow-up resolution on developing deficiencies.

Recommend new installations or modifications to improve existing facilities and standardization within

specific fields of endeavour.

January 2013 to March 2013

PACIFIC ORIENTAL PTE LTD

TELOK A PLATFORM EXXON MOBIL Project - : Malaysia (Offshore)

(Posting in SEADRILL WEST LEDA)

POSITION : Electrical Engineer (Mechanical Completion & Commissioning)

(Permit To Work & Safety Coordinator) PTW

JOB DESCRIPTION

Supervised & performed Mechanical Completion scope of works.

Supervised & performed line & resistance check for all electrical cables both for power cable & control

cable.

Supervised & performed resistance check for all motors prior to pre-commissioning.

Performed High-pot Test for MV cable, transformer, HV switchgear.

Contact Resistance Testing for Bus Bars & ACB's, Commissioning for MV, LV Switchgears

Attend safety meetings with various disciplines for Permit to Work discussion.

Conduct regular site inspection on machineries, equipment, working area, building facilities and storage of flammable/combustible materials for hazards, noise & toxic as per statutory requirement

Implement and maintain safe work practices at work site.

Report safety discrepancies to Project Manager and recommend corrective action

Rectify any unsafe practices or conditions at the work site

Assist in preparation of Job Safety Analysis and Risk Analysis

Prepare and maintain all WSH related documents, participate in WSH committee meeting

Undertake assignments such as safety promotion campaigns, development of risk assessment templates

and safety procedures, as well as safety training for internal parties

Other WSH related ad-hoc tasks as assigned by supervisor

April 2012 to December 2012

EFAF ENGINEERING SERVICES

ABB HV/LV ELECTRICAL PROJECT - Island-wide, Singapore

POSITION : Electrical Engineer (Project Installation, Testing & Preventive Maintenance Servicing)

JOB DESCRIPTION

Handle electrical equipment failure analysis, trip reports, plant's drawings Red-Marking, cost estimation,

and technology adaptation.

Support Inspection, Operations and Maintenance to evaluate and resolve concerns related to plant

electrical equipment, and work with vendor technical representatives where appropriate to resolve

technical problems with equipment.

Prepare and review in-house design packages and drawings, and conduct technical reviews with Project

Engineers and other stakeholders to resolve issues. Also, review all package submittals as required.

Support the pre-commissioning activities with internal and external stakeholders and participate in

commissioning, providing technical support for ongoing major capital projects.

Troubleshoot electrical systems failures such as adjustable frequency drives that control the power

supply to DR-1/DR-2 shipping facility motors and UPS systems that feed power to instrument field

devices in case of power outages.

Perform Factory Acceptance Tests (FATs) and Site Acceptance Tests (SATs).

Provide support for fire alarm system operation and maintenance.

Review Job Safety Analysis (JSA) for work related to electrical equipment.

Provide support to Management of Change (MOC) as required and develop a comprehensive

program to implementation interventions to improve operations.

Estimate costs, prepare justifications and complete expenditure requests as required, and also

support the preparation of purchase orders for electrical equipment procurement.

Prepare failure and investigation reports. Participate in coordination of activities related to the electrical

network. Provide support to the Capital Project Program in review of technical specifications

Jan 2012 to March 2012

OGRE PTE LTD

SBM FPSO CIDADE DE ANCHIETA PROJECT - Keppel Tuas Shipyard, Singapore

POSITION : E&I Comp-EX Inspector (Mechanical Completion, Commissioning)

JOB DESCRIPTION

Detail visual inspection of all hazardous area, ex certification instrumentation and to ensure

installation and equipment meet relevant standards IEC 60079-10.

Visual inspection for complete and corrective installation of unit control panel.

System wiring matching, System cabinet wiring trouble shoot.

In addition, cable schedule. Inspect electrical apparatus and Instruments for hazardous area requirements

like zone, category, class/division and EPL category. Comp ’Ex’.

Performed Equipment & System preservation using plastic, canvass, DENSU Tape for enclosures.

Curing of punch-list, daily job progress and coordinating with engineering department for design

modification methods of protection (ATEX) report to the senior construction manager.

Feb 2011 to December 2011

ASIAPAC COMMISSIONING SERVICES PTE LTD

MODEC BP ANGOLA PSVM FPSO PROJECT-Jurong Shipyard, Singapore

POSITION : Senior Electrical Supervisor (Mechanical Completion & Commissioning)

JOB DESCRIPTION

Supervised & Performed Mechanical Completion scope of works.

Supervised & Performed Equipment & System preservation using plastic, canvass for enclosures.

Supervised Inspection, testing, site surveys all the electrical system.

Supervised & Performed line check for all electrical cables both for power cable & control cable.

Supervised the testing of equipment and control systems Main Switchboards,http://www.terasaki.com.sg/html/pds-ms.htm Emergency Switchboards.

Perform IR Scan for all ACB, CB, Bus Bars joints.

Perform rack-in & rack-out of LV & HV Circuit Breakers and Isolator Switch.

Testing of LV & HV Power Cables using Megger Tester.

Performed High-Pot Test, check protection relays, testing either Primary or Secondary Injection.

Record all data during testing for ITR clearing.

September 2010 to January 2011

MEGGAWATTS ENGINEERING SERVICES PTE LTD

SEA DRAGON II SEMI-SUBMERSABLE PROJECT - Jurong Shipyard, Singapore

POSITION : E&I Engineer (Electrical & Instrument Installation & Mechanical Completion)

JOB DESCRIPTION

To carryout revision of drawing, job technical evaluation, planning, supervision and co-ordination

for loop-check, pre-commissioning and commissioning works.

Preparation of Electrical & Instrument inspection test record (ITR’S) as per specification.

Study & review vendors drawing documents & ensure implementation in compliance with specifications.

Conduct Electrical & Instrument inspection, installation, modification & fabrication done by contractors.

Prepare site inquiries for Electrical/Instrument fabrication installation and issues within the contractors.

Prepares project work schedules progress monitoring and daily/ weekly progress report.

June 2010 to August 2010

WARTSILLA SINGAPORE PTE LTD

SBM OKHA FPSO PROJECT - Keppel Tuas Shipyard, Singapore

POSITION : E&I/Telecoms Supervisor (Telecoms & Instrument Inspector & Mechanical Completion)

JOB DESCRIPTION

Pre-commissioning and commissioning of the following FPSO Telecommunication Systems.

Visual inspection for complete and corrective installation of unit control panel.

In addition, cable schedule. Inspect Telecoms apparatus and Instruments for hazardous area requirements

like zone, category, class/division and EPL category. Comp ’Ex’.

Curing of punch-list, daily job progress and coordinating with engineering department.

Review document’s prior to TELECOMS and INSTRUMENT completion acceptance before START-UP.

Reporting to the senior construction manager.

August 2009 to April 2010

PAN GREATWAYS ENGINEERING PTE LTD

BW OFFSHORE CASCADE & CHINOOK FPSO PROJECT

POSITION :E&I Supervisor (Electrical & Instrument Installation & Mechanical Completion)

JOB DESCRIPTION

Supervise technical staffs and contractors activities for optimum availability, efficiency for ongoing

installations for E&I systems.

Supervised, coordination, monitoring and implementation of all E&I activities, addition/alteration,

upgrading and/or refurbishment works of the project.

Performed mechanical completion inspection, Punch clearing, commissioning of Ship’s HVAC

Air-Conditioning System such as Chillers, Air-handling Unit (AHU), and air Dampers.

Performed Instrument loop-checking, calibrations and commissioning of both existing and newly

installed instruments such as pressure, level, temperature, flow transmitters.

Attend to meetings and prepare monthly report for submission to client and management.

Supervised & Troubleshoot faults, undertake root cause analysis and ensure system recovery.

March 2009 to July 2009

PAN GREATWAYS ENGINEERING PTE LTD

CHEVRON ORONITE EXPANSION PROJECT

Chevron Oronite Pte Ltd, Jurong Island Singapore

POSITION : M&E Project Lead (M&E Installation & Commissioning)

JOB DESCRIPTION

Responsible for the project cycle initiation to closure and covering functions as a Project Engineer.

Execute Mechanical & Electrical works and Supervise and monitor all site work.

Liaise with Clients, Project Manager, sub-contractors and suppliers.

Site technical, coordination and safety meeting HVAC; Mechanical & Electrical & Other Discipline.

Able to liaise with Consultants, Authorities, Builders & Subcontractors.

Able to guide and lead a team of in house work force.

Manage the overall project planning, propose and implement corrective actions to ensure smooth

delivery of project.

Provide the project evaluation and project status to management on a regular basis.

September 2008 to February 2009

PAN GREATWAYS ENGINEERING PTE LTD

PROSAFE PETROBRAS FPSO CIDADE DE

SAO MATEOS PROJECT - Keppel Tuas Shipyard, Singapore

POSITION : E&I Senior Commissioning Supervisor (E &I Inspector MC and Commissioning)

JOB DESCRIPTION

Supervised & carry out hot loop check & testing for process instruments; E&I System.

Supervised & Carry out loop testing, calibration, simulation, troubleshooting, of all process instruments

used to measure, monitor, records and controls different process variables such as flow, pressure, level, temperature and others.

Supervised the Testing, simulation of motor interfacing at HMI and DCS such as motor status signal,

start/ stop command, manual/auto status, and PSD interlock.

Familiar in working with instruments use in Distributed Control System.

Responsible for the DCS P&ID, I/O List, Shop Drawings, Instrumentation Location Layout, Isometric

Drawings Details for DCS, Prepare & sign for all the ITRs for the completed hot loop check/functional check

from CCR to Field Instrument, and submit to the PIMS to clear PC ITR.

January 2007 to August 2008

PAN GREATWAYS ENGINEERING PTE LTD

CONOCO PHILIPS BOHAI FPSO PROOJECT

Sembawang Shipyard, Singapore

POSITION : Telecoms Lead Engineer(Project Management Team SSPL)

JOB DESCRIPTION

In-charge of the TELECOM System Installation for the BOHAI FPSO Project from Conoco Phillips.

Responsible for the installation, carry over works.

Perform weekly progress report & submit to the Manager.

Review, check, approved & signed Inspection Test Record (ITR) sheet, prepared by TELECOMS

Supervisors. Coordinate and liaise with vendor and contractor’s representative in the field concerning

work progress, outstanding issues and other related matters.

Supervise installations, pre-commissioning & commissioning of Telecommunications equipment.

Attend Tri-party inspection with client and contractors.

Responsible for punch list items and mechanical completion work scope.

To carryout revision of drawing, job technical evaluation, Planning, supervision and co-ordination for,

Loop check, Pre-commission and commissioning.

Conduct Electrical and Instrument inspection in the installation, modification and fabrication done by

contractors.

Prepare site inquiries for Electrical/Instrument fabrication installation and issues within the contractors.

Assist client to modify system connections due to changes of design. Responsible for scheduling and

distribution of job orders.

Compiling all as-built drawings and update latest revision as per Engineering design for proper

documentations and references.

Attend daily meetings with client, subcontractors for work progress and technical aspect.

August 2001 to February 2006

System on Silicon Manufacturing Company PTE LTD

WAFER FAB MANUFACTURING COMPANY

Pasir Ris Industrial Drive 1, Singapore

POSITION : Facilities Senior Associate Engineer (Facilities Maintenance & Additional Project)

JOB DESCRIPTION

Operate and maintain facilities systems such as Control, Electrical, Air-conditioning and Mechanical

Ventilation Systems, Fire Protection & Detection, Ultra Pure Water, Clean-room System,

Industrial Waste Treatment Plants and Chemical and Gas Systems for a Wafer Fabrication plant.

Review of system status in FMCS and alarm analysis, Trouble-shooting Facilities alarm response

& service normalization, Perform scheduled preventive maintenance (PM).

System calibration on a timely basis, Perform first line incident handling, alarm response

and breakdown repair works as well as actively participate in ERT incident.

Trouble-shoot and service normalization on systems in charge such as buildings issues, lifts,

plumbing and sanitary, landscaping and housekeeping work

Perform scheduled preventive maintenance (PM) and system breakdown maintenance (BM)

Perform 1st line incident handling, breakdown repair works as well as actively participate in incident

Perform inspection rounds on 6S and supervision of contractor works on building services

Ensure that all quality expectations are up held to meet better than expected customer request

Create and innovate new methods for continuous improvement to current Procedures to attain

best in class quality and cost

Participate in Improvement teams to enhance system improvements

Maintain good housekeeping in all buildings, ensure good safety practice and also safe custody

of keys, tools, documentation, equipment and other properties belonging to the company

Ensure all site safety compliance are met as part of daily responsibility and expectations

Continuously seek to enhance on existing safety procedures for continuous improvement

Plan, lead and supervise work carried out by vendors

Provide leadership in first line of trouble shooting of any process inadequacy

June 1996 to July 2001

UTOPIA-AIRE PTE LTD

M&E/SECURITY SYSTEM INSTALLATION & MAINT

Singapore Island-wide, & Regional

POSITION :Electrical Electronics & Air-Con Engineer (Electrical, Security Access System & Air-con

Installation & Maintenance)

JOB DESCRIPTION

Lead a team of Technical Officers in performing installation T&C, preventive maintenance and corrective maintenance of mechanical & electrical systems such as air-conditioning equipment.

Perform instrumentation set up and testing of refrigeration systems

Perform service and maintenance of laboratory and test cell facilities.

Lead and performed in calibration of test equipment, & particle counters for Clean-room monitoring.

Security System (Card Access System) Installation, T&C and maintenance.

Transformers, HV and LV Switchboard Servicing, HIGH POT Testing, Partial Discharge.

IR Scanning for all ACB, CB, Bus Bars joints, Primary & Secondary Injection Testing for Relays.

Contact Resistance Testing for Bus Bars & ACB's, Performed resistance check for all cables.

Perform rack-in & rack-out of LV & HV Circuit Breakers and Isolator Switch.

January 1994 to April 1996

METRO (GAISANO) AYALA CENTRE

COMMERCIAL BUILDING PROJECT & MAINTENANCE - Cebu City, Philippines

POSITION : Engineering Department Head (Building Facilities Installation & Maintenance)

JOB DESCRIPTION

Supervise and direct the performance of repair jobs scheduled by Building Maintenance Section Head.

Evaluates and presents for interview request for new equipment and recommends purchase of

replacement parts.

Implement through assignment of tasks safety and fire prevention policies and procedures.

Review and

Contact this candidate