MALAK AHMAD

Address: Lebanon-Saida

Phone Number: +961-**-******

E-mail Address: adm0yr@r.postjobfree.com

OBJECTIVE

I am a fresh Civil and Environmental Engineering graduate from the American University of Beirut. I am currently pursuing my Master’s degree in Renewable Energy studies in the Lebanese /Saint Joseph's University program. It was a fruitful add to my research experience. In addition to this, I did my internship at my donor's company "Dar Al- Handasah". It was a pleasant experience as I acquired intensive knowledge of mostly used software and managed to complete all given tasks well before due under a well-organized and professional environment. Moreover, I practiced teamwork throughout my voluntary activities. Finally, in my latest work at Alreaya, I monitored the work of volunteers and workers upon working for the enhancement of damaged houses after Beirut’s explosion. I am coupled with excellent skills in Sap2000, SAFE, AutoCAD, primavera p6 and most Microsoft office software. EDUCATION

From 09/2015 to 1/2020 American University of Beirut Beirut, Lebanon

-Bachelor Degree in CIVIL Engineering, graduated in December 2019 Relevant Courses Taken:

Construction Planning & Scheduling, Construction

management, Highway Engineering, Pavement Engineering, Environment Sustainable Renewable Energy Sources, Surface Water Quality Modeling &Management, Engineering

Hydrology.

Final year project: “A new beginning for Australia Street” Award: Unite Lebanon Youth project Scholarship student

(Donor Dar el Handash)

From 9/2020 to 7/2021 Lebanese University - Saint Joseph's University Beirut, Lebanon

- Master Degree in Renewable energy

Thesis Title: “Hierarchized Hybrid Model Predictive Control For Energy Management in Building”.

-Relevant Courses Taken:

Wind, Solar, Photovoltaics, Hydrolytic, Biomass energy, Energy storage, Evaluation of a Project, Energy efficiency, Green buildings, Modeling of Optimum Thermal System. EXPERIENCE

From 08/2020 to 11/2020 Al-Reayya Assembly Beirut, Lebanon

(3months) Position held: Civil Engineer

Assisting and mentoring Al-Reayya assembly in data entry.

Taking measurements for most damages of the assigned houses in Beirut area because of Beirut’s explosion.

Following up volunteers plus workers in the daily works done by al Reayaa for the enhancement of damaged houses after Beirut’s explosion. From 01/2020 to 06/2020 Pitch worthy Organization with Asfari Challenge Beirut, Lebanon

(6months) Position held: Volunteer Mentor (Remote)

Assisting teams by giving advices.

Following up the designed teams and giving approvals on work. From 05/2018 to 07/2018 Dar el Handsah Beirut, Lebanon

(3months) Position Held: Internship (Structural Department)

Read and revised important chapters in ACI code.

Revised witney’s block in flanged and rectangular section with types of torsion.

Designed a water tank in Dubai area by determining loads, reinforcements, and checking shear.

Designed the surface of a culvert after studying all the critical cases.

Checked load combinations of the culvert according to ASHTO.

Designed the culvert on SAFE program after an intensive revision for SAFE then checking reinforcements and results with excel sheets.

Designed the walls of the culvert on SAPP program.

Designed the raft of the culvert on Safe.

Designed the columns of the culvert using SP columns program.

Checked the overturning, sliding and bearing capacity of a retaining wall.

Identified the forces, overturning moments, factor of safety and finally the reinforcements of the retaining wall.

Worked with pre-stressed concrete aiming to identify the diameter of the jacking, transfer and service PT bars after checking the forces and the properties of the section already given.

Calculated the total stresses at top and bottom after placing PT to check them with the limits in ACI code.

Introduced to CSI bridges program.

Corrected a whole building by checking slabs thicknesses and columns dimensions to add newly designed beams where needed in all the floors.

Used ETABS program to check the corrected building after its final design. From 10/2017 to 12/2017 Eng. Abed el Ghani’s office Beirut, Lebanon

(2months) Position held: Trainee

Trained to do AutoCAD drawings.

EXTRA CURRICULAR ACTIVITIES

Volunteer in summer programs.

Private tutor since 2011 until 2018.

Assisting Al-Reayya assembly in voluntary works and activities.

Collaborating with other NGOs for Social and Environmental voluntary activities. SKILLS

Languages: Fluent in English and Arabic (writing, reading and speaking). Computer Skills: MS Word, Excel, PowerPoint, Access, Internet use, AutoCAD (2D & 3D), MATLAB, C++, Visual Basic, ArcGIS, Digital theodolite, Leveling system, Global Positioning System (GPS), SAPP, SAFE, ETABS, Revit, CSI bridge, SP columns, Design builder and Primavera p6.

Research Skills: Data collection, Data Analysis using excel. Technical Skills: Surveying, Procurement and Scheduling. Soft Skills: Leadership, Communication, Team Building, Organizational, Management and Public Speaking.

Contact this candidate