Ray Taboada

**** *. **** ******

Hollywood, FL **021

786-***-****

adlgn1@r.postjobfree.com

Education: Cowley College, January 2020 – present

A.S. NDT - Technologies

George Baker Aviation School, June 2015.

Avionics 2 Technician Certification

US Federal Communications Commission General Radiotelephone Operator

License

Bachelor’s Degree, Electronic Engineer Certification, Havana, Cuba 1994

NDT Certification, Penetrant and Magnetic Testing, Hollywood, FL 2018

Repairman License, NDT Level II, Penetrant, Magnetic, Eddy and

inspection license

2006-2009 US Foundry, Inc., Miami, FL

•Installed electrical and electronic parts and hardware in housing and assemblies using soldering equipment and hand tools while recording test results and organizing documentation of analysis.

•Performed PCB rework on thru-hole and surface mount components in accordance to the IPC solder standards.

2010-2013 BE Aerospace, Inc. Miami, FL

•Analyzed malfunctions via electronic test equipment, schematics, and technical publications. Performed maintenance on aircraft avionics and electrical systems.

•Adjusted, repaired, and replaced defective components based on analysis of test results, following schematics, and technical publications, using hand tools.

•Conducted manual testing procedures of electronic circuits.

•Worked in Production and Engineering Dept. proto-type, involved in test, set-up and calibration of main circuit boards.

•Prepared procedures, interpreted schematics and mechanical drawings

•Assembled test fixtures to assimilate circuits in the final product.

•Built power supply test fixtures, replicated load and circuit testing prior to installation on final product device.

•Managed the production of approximately 10 personnel in the repair of over 1000 avionics components.

•Read schematics, diagrams and technical orders to determine methods and sequence of assembly.

•Inspected aircraft avionics components for defects and accuracy of installation.

•Assembled proto-typed circuit for stepper motor control circuit for new stage final test.

•Modified electrical circuit proto-type circuit boards in support of engineering /software. Adapted display board with new Harvester Circuit board.

•Analyzed, identified and repaired audio system components.

•Executed complete inspection of electronic units identifying physical or liquid damages due to misuse.

•Performed re-work procedures and updated software to current OEM standards.

•Conducted and analyzed complete procedure improvement and time studies alongside engineers.

•Executed frequent diagnosis and isolation of malfunctions to component level with the use of schematic and troubleshooting guides.

•Performed functions associated with all manufacturing operations including set-up, calibration, analysis and troubleshooting of circuits, and components and electromechanical assemblies.

•Tested performance of electromechanical assemblies, using test instruments such as oscilloscopes, electronic voltmeters, bridge optics and calibrating.

•Repaired, reworked and calibrated hydraulic and pneumatic assemblies and systems to meet specifications.

•Aligned, fit, and assembled component parts using hand and power tools, fixtures, templates and microscopes.

•Installed electrical and electronic parts and hardware in housing and assemblies using soldering equipment and hand tools, while recording test results and organizing documentation of analysis.

•Performed PCB rework on thru-hole and surface mount components in accordance to the IPC solder standards.

•Managed repair database for RMA, and In-house products.

•Assisted Engineer by testing and recording data on prototypes for new product designs.

•Tested functionality and integrity of product using windows based software. Performed network configurations when necessary.

2014-present Aerospace Precision, Inc. Hollywood, FL

•Produced proto-type, involved in test, set-up and calibration of main mechanical, electromechanical, electrical and avionic units.

•Prepared procedures, interpreted schematics and mechanical, electrical, and electronic drawings.

•Assembled test fixtures to assimilate circuits in the final product.

•Built power supply test fixtures, replicate load and the circuit testing prior to installation on final product device.

•Assembled proto-typed circuit for stepper motor control circuit for new stage final test.

•Modified electrical circuit proto-type circuit boards in support of engineering /software. Adapted display board with new Harvester Circuit board.

•Conducted manual testing procedures of electronic circuits.

•Analyzed, identified and repaired audio system components.

•Executed complete inspection of electronic units identifying physical or liquid damages due to misuse.

•Executed frequent diagnosis and isolation of malfunctions to component level with the use of schematic and troubleshooting guides

•Performed functions associated with all manufacturing operations including set-up, calibration, analysis and troubleshooting of circuits, and components and electromechanical assemblies.

•Tested performance of electromechanical assemblies, using test instruments such as oscilloscopes, electronic voltmeters, bridge optics and calibrating.

•Read schematics, diagrams and technical orders to determine methods and sequence of assembly.

•Examined medical equipment and facility's structural environment and checked for proper use of equipment to protect patients and staff from electrical or mechanical hazards and to ensure compliances with safety regulations.

•Repaired, reworked and calibrated hydraulic and pneumatic assemblies and systems to meet specifications.

•Aligned, fit, and assembled component parts using hand and power tools, fixtures, templates and microscopes

Certifications, Licenses and References available upon request.

References Available on Request

Contact this candidate