SREYAS M PILLAI

Last Updated on **th March ****

Contact

JAYAMANDIRAM,

VADAKKUMTHALA

KIZHAKKU,

VADAKKUMTALA P.O

Mobile no:

+91-701*******

Email:

adj8qa@r.postjobfree.com

Languages

English,Hindi,malayalam

Programming

Languages

C++

Simulation

Packages

ANSYS(Fluent).

Objective

Looking for a challenging career which demands the best of my professional ability in terms of technical and analytical skills, and helps me in broadening and enhancing my current skill and knowledge

Education

2017–2019 M.Tech in Thermal And Fluids( 8.02 cgpa) Amrita school of egineering,kollam,kerala 2013–2017 B.Tech in Chemical Engineering( 73.36 Per) TKM Collage of Engineering,Kollam,Kerala 2011-2013 HSE PCM (96.56 Per) Govt. Boys HSS,Chavara, kollam 2011 SSLC :- All(93 Per) Govt. Boys HSS,Chavara, kollam Projects

2018-2019 M.Tech Thesis : Effect of dual splitter plate on the flow around a circular cylinder

1. This work aims to investigate the effect of two splitter plates on the flow around a circular cylinder experimentally and numerically at a Reynolds number 1609. Here two splitter plates with the length same as that of a circular cylinder (D) is considered one at upstream and the other at downstream.

2. These splitter plates are arranged along the centreline of the circular cylinder .Their positions are denoted with upstream gap ratio (G1/D) downstream gap ratio (G2/D). 3. Both G1/D and G2/D ratios are varied from 0 to 2.5 in order to investigate the effect of gap ratios on Strouhal number and Drag Coefficient. 4. It is observed that for Re=1609, minimum drag due to introduction of splitter plates occur at G1/D =0.5 and G2/D =1.5, and a total drag reduction of 29.9is obtained compared to that of a standalone circular cylinder. Publication: Published in the International Journal of Mechanical and Production Engineering Research and Development

2017 BTech project: Novel Three-Way catalytic converter 1. Prepare a novel three way catalytic converter using nano copper and Fe-TiO2 and thereby reducing the use of Expensive catalyst such as Platinum, Palladium and Rhodium.

2. This type of catalytic converter also increases efficiency by exposing maximum surface area of catalyst to the exhaust stream. Checking the emission reduction of the novel three-way converter for petrol, diesel and gasoline- ethanol blend fuel. 3. The modified converter will be cost effective, pollution free and more efficient than the existing catalytic convertors The main achievements of this project are: 4. It was observed that the amount of CO, HC, NOx was reduced significantly after the novel catalytic converter was installed. On comparing the results obtained from the gas analyzer, the amount of pollutants corresponding to specific RPMs, the values obtained were significantly low in the case of novel catalytic converter. 5. The test results show that the use of 80 per gasoline and 20 per ethanol with novel three-way catalytic converter reduces significantly.Therefore it is concluded that novel three-way converter system can be an effective approach in the place of expensive metal based catalytic converter

Work History

Skills

Hobbies

Process Engineer at Ashapura Petroclay Ltd (October 2020- present) 1. Learned about bentonite clay,clay catalyst, acid activation of clay. 2. Learned about the process like crushing, milling, drying, pulverisarion. 3. During my work on ETP plant I gained knowledge on neutralization, filter press, sedimentation, clarification, ultra filtration, sand filter and reverse osmosis. Graduate Apprentice Trainee-Bharat Petroleum Corporation Ltd (2019 January to 2020 January)

1. Gathered information on the working of DCS and BOSS panels,different types of storage tanks, pumps, heat exchangers, etc...

2. Interpreted job site supervisor’s orders and technical documentation to complete accurate work.

3. Learned how to complete given task with minimal supervision, contributing to successful Result

4. With the refinery working environment experience I am confident to work in any chemical and related industries

1. Good Management skills

Management Skills which require in company

2. Quick Learning Capability

3. Good in Communication

1. Daily Running

Go for running on daily base.

2. Sports

Like Badminton and Cricket.

3. Learn new things

Learn about the latest technology which helpful in company and Improve my Skills as well.

Contact this candidate