Network Engineer Sec School

*

IMTHIYAS M I NETWORK ENGINEER

adhqz8@r.postjobfree.com

Mobile No: +91-897*******

Objective:

To troubleshoot complex networks. To acquire knowledge of new products in networks. Present Job:

Working as Network Engineer cum faculty for CCIE (R & S) in ORBIT COMMUNICATIONS From past 2 years.

Roles and Responsiilities:

Preparing of Bills.

Preparing of BOQs.

Education Qualification:

Post Graduation(MCA)

I completed my MCA at Aalim Muhammed Salegh college in Chennai.

(2016 Passed out)

Under Graduation(B.sc (CS))

I completed my B.sc(CS) at Jamal Mohamed College in Trichy

(2014 passed out).

Higher Secondary(12th):

I completed my 12th standard at Imam Gazzali Matric Hr. sec school in lalpet.

(2011 passed out)

Higher School(10th):

I completed my 10th standard at Imam Gazzali Matric Hr. sec school in lalpet.

(2009 passed out)

Skills in Computer Networks:

Fair good knowledge in OSI model

Movement of packet from L7-to-L1 using the headers such as TCP, IP & Ethernet Frame. TCP Header- OP-Codes, Slow Start, Congestion avoidance, Fast Retransmission, Recovery 2

IP Header - Default IP header size, IHL, Flag, Fragmentation of data between two routers based on MTU size, TTL, Protocol no.

ICMP Messages- Troubleshooting networks using ICMP protocol.

(Types and Codes)

Subnetting: Designing of VLSM for ISP and enterprises networks based on their requirement. IP Routing

OSPF

Troubleshooting OSPF not getting adjacencies, when it is stuck in INIT, EXSTART, EXCHANGE, & LOADING states using the log messages. Understanding of OIA, OE1, OE2 in Multi area to increase the performance of low end router by making the area as STUB, Totally STUB, NSSA, Totally NSSA.

Establishing OSPF adjacencies in NBMA devices. Making WAN environment into LAN environment.(Using Same subnet, Using different subnets)

Configuring NBMA devices using Multi-Hub & Multi-Spoke environment.

When areas are not connected to area 0 then by using Virtual-link and exchanging the OSPF data.

Configuring OSPF when area 0 are partitioned,

Path selection by OSPF cost.

Configuring OSPF using GRE Tunneling, when an area is not connected to area 0 and that is configured with NSSA area.

In multi area’s specifying which router should be the DR while other routers should not participate in DR/BDR election process.

Filtering networks using distribution list.

Manipulation of path using OSPF cost.

Filtering of particular network’s LSA type-3 to other areas.

Configuring the redundant links to come up with in 1 sec auto-cost reference bandwidth.

Configuration of Default-Information-Originate in an enterprise or campus networking and designing of IPv4 VLSM address schemes for the different blocks or projects using NAT to establish the WAN connection. Configuring VLAN’s to the departments Reference RFC 2178,2328

WAN Technologies:

Configuring Point-to-Point using PAP and CHAP.

3

Configuring PPPoE.

Switching

Understanding of MAC-Address table in L2-Switch, Using ARP protocol.

Configuring of Inter-Vlan using different subnets

Configuring Port-Security in ports

Inter-Vlan using L3 switches.

Configuring VTP in Cisco Switches for campus or enterprise network.

Summary Advertisement

Subnet advertisement

Advertisement Request

Understanding of STP

BGP

Establishment of bgp neighbour with the port states.

Resolving ibgp issues using next-hop-self to correct the recursive lookup and route- reflectors.

When multi-home preferring the path using AS-Path attribute using the command prepend.

Path shifting using Weight and Local Preference.

Path shifting using MED-Attribute when configured with different AS’s.

Conditioning the paths or router using the attribute Regular Expression such as ^ & $, _

& $.

Scalability of BGP using Confederation.( Sub-AS)

Removing the Private-AS no’s when advertising to ISP.

Aggregation the networks using BGP Summary-Only, Suppress-Map, Unsuppressed- Map and AS-SET.

When same AS are geographically situated in different location then use the Allow-AS command.

Configure the Router using the Community No-Advertise, No-Export & Local-AS.

Establish BGP connection using Update-source lo 0 with ebgp-multihop.

[an BGP has TTL value set to 1 for EBGP and 255 for IBGP].

Understanding of BGP table with RIB failure when two protocols are enabled to form the full mesh.

Advertising the network using Backdoor.

Hiding of AS numbers in the BGP table

Load balancing when dual home and single home.

4

Conditioning network advertisement

Reference RFC 4893,1772,4271,4456,4278,2385,4277,4276,4274,4273 MPLS

Understanding of MPLS Architecture, LDP Protocol.

Configuring MPLS VPN with RIPv2 Static, OSPF, EBGP and EIGRP as PE-CE Routing Protocol.

Configuring MPLS VPN in such a way that Client Routers have access to HUB but don’t have access to any of each other networks.

Configuring MPLS with Extranet.

Providing VPN transit between Client A & Client B using Back-to-Back VRF exchange between AS-1 & AS-2.

Providing VPN transit between Client A & Client B using MP-EBGP VPNV4 exchange between AS-1 & AS-2.

Providing VPN transit between Client A & Client B using Multi-hop MP-EBGP for VPNV4 Exchange.

Configuring an MPLS Carrier Supporting Carriers Architecture AS-2 as the Backbone Carrier and AS-1 as the Customer Carrier to provide transit between private AS.

Configuring an MPLS Carrier Supporting Carrier Architecture with AS-2 as the Backbone Carrier and AS-1 as the MPLS Enable Customer Carrier to provide transit between Private AS.

Configuring an MPLS VPN between Clients over AS-1, only Traffic between AS loopback should be label switch throughout AS-1.

Configuring MPLS VPN Export Map, when two Vlans in the head office and different locations each vlan is configured, each Vlan should not communicate to each other.

Configuring two MPLS Traffic Engineering tunnels between Client- A to transport traffic between Client- B. Traffic Engineering tunnels with a total guarantee of 10Mbps between Client-A to transport traffic between Client-B. 1/3 of the traffic between these devices should use dynamic path.

MPLS Traffic Engineering Unequal cost load balancing.

Configuring SHAM Link between PE to PE.

5

EIGRP

Metric Calculations using the formula.

Understanding of null 0 in the EIGRP routing table.

Load balancing using the variance command.

Configuring EIGRP Stub, Summary-only, Connected & Receive-only. ISIS

Configuring ISIS between the routers

Setting the routers for L1, L2, L1/L2 areas

Specifying the DIS router

IPv6

Summarize loopback interfaces in Routers such that the other Routers will only have a single entry in the Routing table.

IPv6 Tunnels 6to4

IPv6 Frame-Relay

IPv6 RIPng

IPv6 BGP

Filtering the network using Access-list, Prefix-list and setting value using route-map. NAT – configuring Static, Dynamic & PAT, TCP load balancing Redistribution between protocol and filtering networks using Distribute-list Redistribution between RIPv2, EIGRP, OSPF using distance and setting tag. Limiting the number of OSPF redistribution, the maximum number of prefixes that can enter into ospf areas.

Advanced Loop Prevention between RIPv2, EIGRP and OSPF Network Migration.

LOAD BALANCING such as GLBP, HSRP & VRRP.

6

Personal Details:

Father Name : Mohamed Ibrahim.

Date of Birth : 29-01-1993.

Sex : Male

Nationality : Indian

Marital Status : Single

Passport No : R4775719

Passport Valid : 26/10/2017 To 25/10/2027

Language Known : Tamil, English, Arabic(Read,Write& Speak). Declaration:

I hereby declare that above information is true to my knowledge With Regards,

IMTHIYAS MI

Contact this candidate