SANTOSH KUMAR G

Email: adh5hc@r.postjobfree.com

Cell: +91-827*******

Objective

Seeking a Hardware Engineer position with an organization where my electronics and analytical skills together can help in the design and development of hardware circuits for various devices. Looking for a challenging position which enhances the quality of design with minimal cost thereby adding strong business value to the organization. Core Skills

Excellent knowledge of product requirements plans and estimate development activities including electronic system architecture diagram creation.

Hands on experience with Altium Tool (or equivalents).

Expertise in Digital/Analog Circuit design, Manual testing, PCB troubleshooting, Simulation, Schematic Capture, Embedded C programming, FMEA processes.

Good knowledge in designing embedded system based on Microcontroller/ Microprocessor and associated subsystems such as the power supply, I/O interfaces, displays and communications modules.

Handling the diverse testing instruments Oscilloscope, Logic Analyzer, Digital multi meter, Current source, Regulated power supplies, Function Generators, 3 phase variac and Soldering tool

Proficiency in reading/reviewing datasheets of design drawings, wire harnesses, electronic components.

Involved in Prototype products Development, Test strategies, Test case generations, BOM generation and Creating test plans

Strong knowledge on ADC, DAC, JTAG and PWM units. Expertise in communication protocols SPI, I2C, UART and CAN.

Preparing Documents like Test cases, Factory acceptance test, Instruction Manuals.

Experience in board bring-up, circuit level, troubleshooting and testing, hardware validation, timing analysis.

Experience in Components selection and validation.

Knowledge of EMC/EMI standards, battery management systems and battery charging. AC-DC, DC-DC power supply and Lithium-Ion battery charger design., Work Experience

1. JVS Electronics Pvt Ltd, Bengaluru, India

Position: Hardware Engineer

Duration: September 2019 – Present

Projects Worked:

I. Transformer protection relay (JD100)- To have overall over current and over voltage protection for protection. Designing using Microcontroller/ Microprocessor

(PIC16, PIC32) and associated subsystems such as the power supply, I/O interfaces, ADC, Signal conditioning circuits, displays and communications module.

II. Trip Circuit Supervision Relay (TCSR)- TCSR is used for monitoring healthiness of the circuit breaker (CB) trip circuit, CB trip coil and CB power supply. The monitoring of two trip coil circuit has to be done by only one TCSR. III. Automatic power factor correction (APFC)- To have automatic power factor correction in power system application. It uses MCP39F521 microchip IC to have control and monitoring of power factor of system.

IV. Universal Switch mode power supply card- (18-265V) universal power supply card which is capable of supplying various compact power system device. 66 kHz option for highest efficiency requirements, Accurate programmable current limit, Optimized line feed-forward for line ripple rejection, Frequency jittering reduces EMI filter cost, fully integrated soft-start for minimum start-up stress, 725 V rated MOSFET, Simplifies meeting design derating requirements. 2. Sunil Construction, Raichur, Karnataka, India

Position: Maintenance Engineer (Karnataka power corporation ltd (KPCL)) Duration: November 2016 – July 2017

Roles and Responsibilities:

Operation and maintenance of electrical equipments in power plant, Energy audit report preparation, troubleshooting, project erection management. Ash handling plant vacuum pump operation.

3. ABB India ltd, Bengaluru, India

Position: Post Graduate Intern

Duration: September 2018 – December 2018

Roles and Responsibilities:

12 Pulse Converter design

DC DC Converter analysis using MATLAB

Modelling of various DC-DC converters.

I. Academic Projects:

1) Design &Development of slow and fast Battery charging for Electric Vehicle Application. Inter-phasing of AC port charging to DC Fast charging circuit for present vehicles (M. Tech Projects)

2) Underground cable fault distance locator (Prototype hardware & software). The objective of this project is to determine the distance of underground cable fault from base station in kilometers. (B.E/B.Tech Project)

3) Designed and developed a project called ‘5KW Solar system for Computer lab’ in final year of diploma.

II. Paper Publications:

1) Paper Presentation in “International Conference on Emerging trends in Engineering, Technology and Management 26th - 27th April 2019” on “Closed loop Control System Simulation of 12 Pulse Rectifier for Transient changes in Source Inductance” 2) Paper Presentation in “International Journal of Emerging Technologies in Engineering Research (IJETER) Volume 7, Issue 5, May (2019)” on “Design, Specification and Simulation of Slow & Fast Battery Charging for Electric Vehicle Application” 3) Paper Presentation in “NATIONAL CONFERENCE ON KNOWLEDGE DISSIMENATIOIN OF PG PROJECTS AND RESEARCH WORKS 7-8thMAY 2018” on “Modeling, simulation and analysis of Integrated Dual Output Converter using PSIM”

Education

S. No. Qualificatio

n

Institution Year of Passing

1 M.Tech (Power Electronics) R.V. College of Engineering. August 2019 8.25 CGPA

2 B.E. (Electrical & Electronics Engg) Navodaya Institute of Technology

July 2016

71.31 %

3 Diploma (Electrical & Electronics Engg) Govt. polytechnic, Raichur. May 2013 4 SSLC KPCL High School,

Shaktinagar

March 2010

Extra-Curricular Activities

● National Cadet Corps (NCC) for ‘A’ ‘B’ and ‘C’ Certificate, under the

‘35KARNATAKA BN NCC, RAICHUR’ in Diploma.

● 1st prize in TECHNICAL TALK on “CIRCUIT BREAKERS” (2016) Declaration

I, hereby declare that all statements made are true, complete, and correct to the best of my knowledge and belief.

(Signature)

Santosh Kumar

Contact this candidate