Mechanical Technician
Resume:
NAME: JEFFREY R. ENRIQUEZ
ADDRESS: BURGOS, PILAR, BATAAN, PHILIPPINES/ Muscat, Oman
MOBILE NUMBER: +639*********/+639*********/
EMAIL ADDRESS: ****************@*****.***
Objective: To be part of this company and work professionally and apply my capabilities, skills knowledge and to develop my personal skills and contribute my years of experience in which I can effectively utilize my expertise in technical knowledge.
PERSONAL INFORMATION:
BIRTHDATE: May 30, 1983
AGE: 37
CIVIL STATUS: SINGLE
PASSPORT: EC7538785
PASSPORT VALIDITY: APRIL 26, 2021
CURRENT SALARY: 1275 OMR.
EXPECTED SALARY: 3000 USD – 5000 USD.
SUMMARY OF WORK EXPERIENCE:
My years of experience in the field of mechanical from the very start of the plant from the construction., such as installation, leveling, centering, grouting and shafting alignment by using dial gauges or laser alignment., and from construction goes to commissioning, start-up and up to the maintenance of the plant to perform preventive, corrective and shutdown maintenance to ensure the equipment is maintained in a safe and proper manner. And I had been experienced working as a service engineer for the rotating and static equipment as a vendor.
TOTAL YEARS OF EXPERIENCE: 12.1 years
TOTAL YEARS OF OIL and Gas/Petrochem/LNG EXPERIENCE: 11 years
YEARS OF MIDDLE EAST/OVERSEAS EXPERIENCE: 11 years
TOTAL YEARS OF INSTALLATION EXPERIENCE: 11 years
TOTAL YEARS OF COMMISIONING/START UP EXPERIENCE: 2.2 years
TOTAL YEARS OF FIELD MAINTENANCE EXPERIENCE (preventive and corrective): 6.6 years
TOTAL YEARS OF SHUTDOWN EXPERIENCE: 7 years
DETAILED WORK EXPERIENCE:
TERM OF SERVICE: OCTOBER 2019 – TO PRESENT
COMPANY 1: NEXUS GLOBAL UNITED LLC.
PROJECT: PETROLEUM DEVELOPMENT OF OMAN
COUNTRY: MARMUL, OMAN
PROJECT NATURE: CRUDE OIL
POSITION: MECHANICAL TECHNICIAN
BRIEF COMPANY PROFILE and DESCRIPTION OF WORK NATURE: To perform preventive and corrective maintenance to ensure the equipment is maintained in a safe and a proper manner
JOB DUTIES and RESPONSIBILITIES:
Execute all assigned general mechanical rotating equipment maintenance activities (PM & CM) in a safe and operating standard.
Provide specialist inputs for rotating equipment applications and problem solving.
Calibrate, trouble-shoot and analyze field rotating equipment during abnormal conditions
Conduct equipment or process parameters to be recorded and all checks to be carried out are captured in the log sheet at required frequency
• Assessment of maintenance contractor's level of skill and equipment handling capabilities.
• Provide input to RCM [Reliability Centered Maintenance] and FMEA [Failure Mode and Effect Analysis] • Asset integrity reviews, Equipment Health-checks, Asset/ Maintenance reference plan), scope challenge reviews.
Record all preventive and corrective maintenance findings, breakdowns, feedbacks and improvements in SAP.
Provide feedback and improvement inputs on Maintenance Craft Procedures and Maintenance Plans to the Maintenance Support Department.
Carry out the required Rotating Equipment inspection tasks, i.e. Perform the non-negotiable tasks, laid down either by legal authorities or recognized "certifying bodies" or determined through a risk based process, to demonstrate system & equipment integrity in accordance with performance standard and deviations are recorded and authorized by the Technical authority
Provide technical support to operations and the startup team in the development of the commissioning, start up and operating procedures for discipline specific hardware.
Execute and comply with Permit to Work System, manpower, materials, tools, services, spares, logistics, staff competences, data collection/reporting, and associated costs.
Deputize as Maintenance Supervisor in the incumbent’s absence.
ROTATING EQUIPMENTS: Reciprocating and Centrifugal Pumps, Air and Gas compressor, Diesel Engine, Fin fan cooler, Beam pump and etch.
STATIC EQUIPMENT: Valves, Vessels, and etch.
REASON FOR LEAVING: Currently working
Employment Gap: None
TERM OF SERVICE: AUGUST 2014 – OCTOBER 2019
COMPANY 2: AL SHIRAH RECRUITMENT SERVICES EST.
PROJECT: ADNOC REFINING
COUNTRY: UNITED ARAB EMIRATES
PROJECT NATURE: OIL AND GAS
POSITION: MECHANICAL TECHNICIAN
BRIEF COMPANY PROFILE and DESCRIPTION OF WORK NATURE: To perform preventive, corrective and shutdown maintenance to ensure the equipment is maintained in a safe and a proper manner
JOB DUTIES and RESPONSIBILITIES:
Perform preventive and corrective maintenance as directed or deemed necessary to ensure equipment is maintained in a safe and a proper manner.
To comply with all company health, safety, and environment as well as work permit policies and procedures.
To perform and participation of preventive, corrective and troubleshooting mechanical maintenance activities of the plant equipment such as pumps(overhang, between bearing, vertical,dosing pump), heat exchanger, diesel engine generator, fan cooler, compressor, bar screen, band screen, diesel fire pump, Bernoulli filter, emergency shower, and valves.
Attends in a maintenance monitoring, inspection and repair of all mechanical equipment within the area of responsibilities and work out maintenance reports and planning schedules.
Reviews own work for completeness and quality workmanship.
Complete required documentation and records.
Follows established housekeeping and safety practices to maintain the quality of the work environment.
To troubleshoot, identify and isolate faulty components on rotating equipment such as pumps, diesel engine generator, bar screen, band screen, diesel fire pump, compressor and fan cooler.
To identify spare parts required for maintenance work, from manufacturers drawing and spare parts lists.
To perform shutdown maintenance repair and overhaul in all rotating and static equipment such as pumps, heat exchanger, fan cooler, diesel engine generator, bar screen, band screen, Bernoulli filter, compressor and valves
Kept the cleanliness from the out and in door of the plantation in daily maintenance job
ROTATING EQUIPMENTS: Pumps, diesel engine generator, fin fan cooler, diesel fire pump, compressor, trash raking bar screen and travelling band screen.
STATIC EQUIPMENT: Heat exchanger, Bernoulli filter, emergency shower, and valves
REASON FOR LEAVING: Resigned
Employment Gap: 3 months gap for visa processing
TERM OF SERVICE: MAY 2013- MAY 2014
COMPANY 3: PETROTEC
PROJECT: CRYOSTAR SERVICES LNG VESSEL / AND OTHER SERVICES IN OTHER VENDORS
COUNTRY: QATAR
PROJECT NATURE: LNG / OIL AND GAS
POSITION: MECHANICAL TECHNICIAN (SERVICE ENGINEER)
BRIEF COMPANY PROFILE and DESCRIPTION OF WORK NATURE: Rapid response to any equipment breakdown on customer sites to ensure that lost production is minimized.
JOB DUTIES and RESPONSIBILITIES:
Rapid response to any equipment breakdown on customer sites to ensure that lost production is minimized.
To ensure at all times that work is completed in a safe manner, to high engineering standards, in compliance with customer standards and procedures and external procedures where appropriate.
To ensure that any customer contact is dealt with professionally and promptly in dealing with queries.
Preparing for maintenance and inspection as required by executing physical isolations and electrical isolations.Responsible for testing and re-starting equipment once is completed.
Resolving problems by rectifying defects and identifying opportunities that will enhance reliability.
Inspect and check machinery and related equipment as required.Diagnose faults on plant and machinery and provide customer feedback.
Maintaining a safe and clean working environment.
Preparing, scoping and assisting in the costing of projects as required.
To make reports, time sheets, mechanical and site checklist signed by the customer before leaving the site.
Workshop: Petrotec
Location: Doha, Qatar
Services of other equipment:
Pump ( Centrifugal and Reciprocating )
Blower
Karcher
Pigs
Gear Box
Compressor
Valve
Check the previous history of the equipment.
If the finding require to overhaul, drain if necessary.( For Pump and gearbox only )
Check the alignment( For Centrifugal Pump with the skid and motor only.)
Use a center punch or marker to mark the casing and some spare parts need to dismantle.
Make a report for the spare parts need to replace and to mention the reason for the replacement.
After the inspection and found the faulty component., Re-assembly with the replacement of new spare parts necessary to replace.
Re- alignment.( For centrifugal pump with the skid and motor only)
Filling the oil.( for pump, and gearbox only)
Install wiring connection for testing.(For pump, blower, karcher, and compressor only)
Check the required volume of flow, pressure, vibration, sound and leak.( For pump, karcher, and compressor only)
Touch up paint after the completion of services.
Wrapping for delivery.
Project: Cryostar LNG Vessel
Location: Ras Laffan, Qatar
Compressor overhauling: (Multi-stage centrifugal)
Permit to work.
Apply lock out and tag out procedure.
Depressurizing the unit.
Check the alignment before to overhaul for reference.
Disconnecting all necessary instrument tubing, wiring, coupling guard, coupling, spacer and all suction and discharge bellows.
Use center punch or marker to mark the casing, coupling and some spare parts need to dismantle.
Dismantling the bulkhead seal.
Remove the casing compressor, shroud, impeller, diffuser, a labyrinth seal, shaft seal, intermediate plate and the back plate.
Check all the clearances for the impeller and shroud.
Make a report for the details necessary to replace and to mention on the report for corroded, broken, erosion and etch.
After the inspection, re-assembly with the replacement new spare parts.
Re-Install the pump coupling and re-connect the coupling spacer.
Re-alignment of a shaft to shaft.
Connect the suction and discharge bellows.
Re-connect the wiring by electrical for testing.
Removed lock out and tag out.
Check the details for the required, required pressure of bar if necessary, the vibration, sound, and leak.
After reaching the required volume of flow, pressure, and the condition is doing better, make a report to the condition of the equipment
ROTATING EQUIPMENTS: Pumps, compressor, karcher, blower, and gear box
STATIC EQUIPMENT: Pigs, and valves
REASON FOR LEAVING: Resigned
Employment Gap: 7 months- waiting for the new employer
TERM OF SERVICE: SEPTEMBER 2011- OCTOBER 2012
COMPANY 4: BONATTI SPA
PROJECT: RAS TANURA SAUDI ARAMCO
YANBU SAUDI ARAMCO
COUNTRY: SAUDI ARABIA
PROJECT NATURE: OIL AND GAS
POSITION: MECHANICAL TECHNICIAN / MILLWRIGHT
BRIEF COMPANY PROFILE and DESCRIPTION OF WORK NATURE: INSTALLATION, CENTERING, LEVELING, GROUTING, SHAFTING ALIGNMENT AND SHUTDOWN MAINTENANCE
JOB DUTIES and RESPONSIBILITIES:
Project: Ras Tanura Refinery ( Saudi Aramco )
Location: Ras Tanura, Kingdom of Saudi Arabia
Duties and Responsibilities:
Pump Overhauling:
Check the report of the previous condition of the equipment before to overhaul.
Permit to work.
Apply lock out and tag out procedure.
Drain the suction and discharge line and the pump.
Check the alignment before to overhaul for reference.
Disconnect all necessary instrument tubing, wiring, coupling guard, coupling, spacer, pipe connection, and blinding both sides of suction and discharge.
Use center punch or marker to mark the casing coupling and spare parts need to dismantle.
The pump shaft with impeller can be lifted out of casing
Dismantling the wearing ring, impeller, mechanical seal mechanical seal, and etch.
Impeller, pump shaft, bearing, mechanical seal and internal volute will be an inspection for erosion, corrosion, pitting and wear.
Make a report for the details necessary to replace and to mention on the report for corroded, broken, erosion and etch.
After the inspection, re-assembly with the replacement new spare parts.
Coupling alignment.
Filling the oil.
Re-Install the pump coupling and re-connect the coupling spacer.
Re-alignment of the shaft to shaft.
Connect the suction and discharge line.
Re-connect the wiring by electrical and re- install the coupling guard for testing.
Removed lock out and tag out.
Check the details for the required volume of flow, required the pressure of bar if necessary, ampere of the motor, the vibration, sound, and leak.
After reaching the required volume of flow, pressure, and the condition is doing better, make a report to the condition of the equipment.
Project: Saudi Aramco Yanbu Refinery
Location: Yanbu, Kingdom of Saudi Arabia
Duties and Responsibilities:
Comply with all company QHSE policies, practices and procedures.
The foundation surface must check the centerline & its elevation.
Chipping the foundation surface to get the exact elevation and to easily apply the grout.
Mounting the machine, and verify the orientation in the drawing.
Take the centering from the center of the machine & the center of the foundation, and the tolerance is not more than 5mm.
Pocket & final grouting will be curing not less than 3 days.
Leveling alignment for the preparation of pocket grouting should be use precision level and take the tolerance not more than .05mm.
Alignment of shaft to shaft by using dial gauge there’s have two possible methods one is the Reverse Alignment method and another one is the Rim and Face method
The formula of Reverse Alignment Method:
[Snf = ( PR + MR /2 ) * ( L2 / L1 ) - ( PR /2 )] ; [Sff = ( PR + MR /2 ) * ( L3 / L1 ) - ( PR /2 )]
The formula of RIim and Face Method:
[RIM = PDR /2] ; [FACE = ( Snf = FRD /D ) ; ( Sff = FR /D )]
After each method such as centering, leveling, shaft to shaft alignment even the foundation centering and elevation, pocket grout, the final grout, installation of the podding plates all prior for inspection by company QC then after passed with the QC. Inspection with the vendor
ROTATING EQUIPMENTS: Pumps, compressors, and blower
STATIC EQUIPMENT: Vessels, heat exchanger and valves
REASON FOR LEAVING: Resigned
Employment Gap: 6 months- waiting to return back in Libya
TERM OF SERVICE: MAY 2010- MARCH 2011
COMPANY 5: BONATTI LIBYAN BRANCH
PROJECT: MELLITAH GAS COMPRESSORS SERVICES
COUNTRY: LIBYA
PROJECT NATURE: OIL AND GAS
POSITION: MECHANICAL TECHNICIAN
BRIEF COMPANY PROFILE and DESCRIPTION OF WORK NATURE: To perform preventive, corrective and shutdown maintenance to ensure the equipment is maintained in a safe and a proper manner.
JOB DUTIES and RESPONSIBILITIES:
Maintenance of Five Turbo Compressor units, each one constitutes by Nuovo Pignone General Electric MS 5002 Gas Turbine, equipped with a DLN combustion system driving two Nuovo Pignone Centrifugal Compressors BCL 455 and BCL 356 model.
Duties and Responsibilities:
Perform preventive and corrective maintenance as directed or deemed necessary to ensure equipment is maintained in a safe and a proper manner.
To comply with all company health, safety, and environment as well as work permit policies and procedures.
To perform and participation of preventive, corrective and troubleshooting mechanical maintenance activities of the plant equipment such as pumps, heat exchanger, gearbox, fan cooler, gas turbine, compressors, and valves.
Attends in a maintenance monitoring, inspection and repair of all mechanical equipment within the area of responsibilities and work out maintenance reports and planning schedules.
Reviews own work for completeness and quality workmanship.
Completes required documentation and records.
Follows established housekeeping and safety practices to maintain the quality of the work environment.
Monthly check up for the oil cooler and the gas cooler.
To troubleshoot, identify and isolate faulty components on rotating, pumps, turbine, gearbox and compressors.Using manual.
To identify spare parts required for maintenance work, from manufacturers drawing and spare parts lists.
To perform shutdown maintenance repair and overhaul in all rotating and static equipment such as pumps, compressors, turbine, fan cooler, gearbox, valve, and heat exchanger.
Kept the cleanliness from the out and in door of the plantation in daily maintenance job
ROTATING EQUIPMENTS: Pumps, turbine, gearbox, compressor and fin fan cooler
STATIC EQUIPMENT: Heat exchanger and valves
REASON FOR LEAVING: Local war
Employment Gap: 6 months- waiting for the new employer
TERM OF SERVICE: JULY 2007-OCTOBER 2009
COMPANY 6: MOHAMMAD AL-MOJIL GROUP
PROJECT: Mono – ETHYLENE GLYCOL PLANT (PETRORABIGH)
PROPHYLENE GLYCOL PLANT (KAYAN 23)
COUNTRY:SAUDI ARABIA
PROJECT NATURE: OIL AND GAS / PETROCHEMICAL
POSITION:MILLWRIGHT
BRIEF COMPANY PROFILE and DESCRIPTION OF WORK NATURE: INSTALLATION, LEVELLING, CENTERING, GROUTING AND SHAFTING ALIGNMENT.
JOB DUTIES and RESPONSIBILITIES:
Comply with all company QHSE policies, practices and procedures.
The foundation surface must check the centerline & its elevation.
Chipping the foundation surface to get the exact elevation and to easily apply the grout.
Mounting the machine, and verify the orientation in the drawing.
Take the centering from the center of the machine & the center of the foundation, and the tolerance is not more than 5mm.
Pocket & final grouting will be curing not less than 3 days.
Leveling alignment for the preparation of pocket grouting should be use precision level and take the tolerance not more than .05mm.
Alignment of shaft to shaft by using dial gauge there’s have two possible methods one is the Reverse Alignment method and another one is the Rim and Face method
The formula of Reverse Alignment Method:
[Snf = ( PR + MR /2 ) * ( L2 / L1 ) - ( PR /2 )] ; [Sff = ( PR + MR /2 ) * ( L3 / L1 ) - ( PR /2 )]
The formula of RIim and Face Method:
[RIM = PDR /2] ; [FACE = ( Snf = FRD /D ) ; ( Sff = FR /D )]
After each method such as centering, leveling, shaft to shaft alignment even the foundation centering and elevation, pocket grout, the final grout, installation of the podding plates all prior for inspection by company QC then after passed with the QC. Inspection with the vendor.
ROTATING EQUIPMENTS: Pumps, compressors, extruders, turbines, fin fan cooler, and etch.
STATIC EQUIPMENT: Vessels, heat exchanger, valves and etch.
REASON FOR LEAVING: Resigned
Employment Gap:1 month gap from my first experience in Philippines but not related to my current designation…
PLANT EQUIPMENT/TOOLS/INSTRUMENTS:
Pumps, diesel engine generator, fin fan cooler, diesel fire pump, compressor, trash raking bar screen and travelling band screen, karcher, blower, gear box, turbine, pigs, Bernoulli filter, heat exchanger, valve and etch…
Hydraulic jack, impact wrench, torque wrench, pneumatic pump, porta lift, puller, wrenches, allen key, screw driver, crow bar, hammer, mallet, pipe wrench, vice grip, drill machine, grinder, air die grinder, power brush, screw driver pistol, pneumatic pump, manual hydraulic pump, pliers, clamp, socket wrench, hole punch, grease gun, grease machine, hack saw, drill press, torch, adjustable wrench, bench grinder, cutter, taps and dies, bearing heater, pipe cutter, chain block, file, tape meter, steel rule, triangle, plump bulb, combination square, center punch and etch…
Feeler gauge, inside and outside micrometer, dial gauge, laser alignment, transit level, carpenter level, mechanical or precision level, pitch gauge, depth gauge, taper gauge, bore gauge, plastic gauge, Vernier caliper and etch…
PLANT MAINTENANCE or OTHER RELATED SYSTEMS:
A.Computerized Maintenance Management System (Indicate here all the Computerized Maintenance Management System –CMMS- like SAP, etc. used or exposed to)
a.Maximo – To find work order number, preventive, corrective and shutdown maintenance daily schedule, progress of the job it’s either completed, in progress, cancel and delay status, man hour, person involve for the job, and etch.
b.Outlook – reporting a daily schedule and status on your respective engineer, senior engineer, section head, coordinator, plant manager, vice president or anyone else need to give a feedback for the job status and also to receive any updated news from the management, job, request the spare parts order, job status and etch.
c.SAP – This all about your information such as your profile, time management, performance status, member of your family, bank account, task request, leave plan, overtime request, violation, time sheet, time attendance, conflict of interest survey and etch.
B.Permit to Work (Indicate all Permit-to-Work –e.g. PTW, JSA, Tool Box Talk, etc. Known and Experienced).
a.TRA-Task and Risk Assessment (indicates the description of task request, hazard, consequences :people/environment/assets/reputation, controls :prevent/detect/control/mitigate, base link risk, additional control measures/action, respective party, residual risk
b.Confined Space entry - due to the limited opening for entry and exit, unfavorable natural ventilation, not designed for continuous worker occupancy
c.Tool box talk – The description of the task where the supervisor discuss the task and how to work safely…
C.Microsoft Office Programs (Indicate all Microsoft Programs you know how to use - Even Basic)
a.Microsoft Office Word
b.Microsoft Office Excel
D.Alignment:
a.Dial gauge – Reverse and Rim and Face alignment of shaft to shaft alignment
b.Laser alignment – Shaft to shaft alignment
c.Leveling and Centering alignment
TRAININGS and SEMINAR:
Training Certificate
2 and 4 Stage Cryostar Compressors Assembly in Shipboard Equipment
Cryostar Service Centre February 2014
EDUCATIONAL QUALIFICATION:
VOCATIONAL COURSE:
2002-2002
Training Certificate
Technical Education and Skills Development Authority
Orion, Bataan, Philippines
COLLEGE DEGREE:
2002-2006
3rd year in Bachelor of Science in Mechanical Engineering
Bataan Peninsula State University
Balanga, Bataan, Philippines
SECONDARY: High School Diploma
1996-2001
Bataan National High School
Balanga, Bataan, Philippines
PRIMARY: Elementary Diploma
1990-1996
Pilar Elementary School
Pilar, Bataan, Philippines
REFERENCES :
Mark W. Dottin
Cryostar Vessel Manager
Khalid Atef Saleh Almestarihi
Senior Engineer in RTA
Abdel Aziz Al Zarouni
Mechanical Supervisor in Adnoc-Takreer Refining
All above information are true and was formatted to suit the requirement of our prospective employer.
Jeffrey R. Enriquez NAME OF APPLICANT
Put Recent Picture Here
Contact this candidate