Engineering Information
Resume:
Anne S Oun
********@*****.***
Lowell, MA 01851
Objective:
Seeking a position where I can expand my knowledge by learning and adapting to new concepts and where my already acquired skills and expertise will contribute towards the company’s success. Experiences:
Mettler Teledo
Billerica, Ma. 3/2018 to
present
Manufacturing Technician 2
Build /assemble mechanical and electrical components/application Enclosure, top housing, bottom housing, laser, assemble accessorizes.
Calibration, measure testing and 12 hour clean bacteria run test debugging,measuring test, CALLIPERS,micrometer,drop gage,scales ruler, multimeter,gauss meter,ir test equipment, voltmeter, oscilloscopes and etc.,bearings, resolver,seals,moulding,adjust, handling adhesives.interpret and verifying specification using simple standup setup test.
Simple troubleshooting, diagnose, rework
Build optical components,laser alignment, moving mirror alignment etc.
Use powertools, hand tools, wrenches, tweezers and etc Ionics Materials
Woburn, MA
2017- 3/2018
E/M Technicians
spread mixed chemical materials flat on the disk
welded the tip of anodes, or cathode to a nickle tap togehter
sealed around the pouch and add electrolyte in the pouch and sealed close
build the pouch together with anodes, cathode and separators
testing the batery, coin cell, pouch cell, double AA
inspect incoming and out going parts
MKS Instrument
Andover, MA
2016- 2017
E/M Technicians
building a censor
using screws, pliers, tweezers, flat head all tools needed etc
rework
inspect all parts before assemble
testing the pcb board before build, wiring stripper, crimping, mechanical and electrical components
multimeter,powermeter, testing and debugging, troubleshooting. Thermo Fisher Scientific
Tewksbury, MA
2011-3/2016
Engineering Technician 2014-2016
Part of R&D Team responsible for the development of new product (Gemini Analyzers)
Worked closely with engineers during creation phase to develop, build, modify, and test units
Studied new product designs and engineering data to build prototypes
Completed documentation for R&D and prototype projects
Accurately recorded assembly processes and test results to develop manufacturing Assembly Instructions
Conducted in-process and final inspections and tests to verify performance specifications
Recorded quality results and identified non-conforming units, diagnosed, investigated and analyzed issues for troubleshooting
Worked with engineers to determine cause of quality/performance issues and made recommendations for process improvement
Experimented using undetermined methods to discover possible solutions for quality/performance issues; such as substitution of materials or parts, rearrangement of components or subassemblies, changes in production procedures, etc.
Assembled mechanical, optical and electronic parts using a variety of production tools, equipment, processes, methods and procedures
Introduced and trained assemblers on building new products and implementing production process
Trained to perform and complete all duties and responsibilities of production including:
Optical engine testing, Thermal system testing, visual inspections, program testing
Trouble shooting circuit and systems
Use of Calipers, micrometer, wave front sensors, camera, power meter, oscilloscope etc.
Adjust, Calibrate, Align Optical and Laser Systems
Software installations
Product Test and Calibrate FT and Raman
Optical spectrum Alignment
Build and Calibrate Anvil
FSE Gui apps for Calibration
Connect flex circuits and pin attachments such as: solder pins, lasers, PC boards, coils, and wires, attach IR source, epoxy and oven cure
Rework and Repair assembly
FTIR system (fourier Transform Infrared) Optics
Vectron International Hudson, NH 2009-2011
Wire Bonder
Working in a Clean room
Inspect 100% underneath microscope
Operate wire bond machine KME hw22u-h, hw 27 Panasonic
Lay out the plates in the plasma before put it into wire bond
After wire bonded place the lots in the 4hr oven.
Testing the component before sending to final inspect.
Operate tacking, seam seal, laser and reflow
Able to read and understand schematics, blue print and BOM.
Utilize small hand tools, calibrated instrument measurement equipment, microscope and text fixtures.
Unicare Credentialing Andover MA. 2006-2009
Verifying provider information by state with visual cactus program.
Date entry personal information and match the correct information by name, address,
date of birth, Social Security Information and license.
Once the status is done and the verifier is clear. Enter the database for imaging to send to the other department to verify associate by vin number.
After print all the data entering of their information put in the credential check list sheet profiles
Know Basic computer like word excel, word processing etc. EDUCATION
HS Diploma-Lowell High School Lowell, MA
Contact this candidate