SACHIN SANGAMESWARAN

Objective

To materialize my potential and fulfil my passion by pursuing a successful career as a Process Engineer in the Chemical Industrial Sector.

Profile

• Qualified M.Sc. (Advanced Chemical Engineering) graduate from University of Manchester and last worked as Process Engineer with Samsung Engineering India.

• Acquired a sound knowledge and experience in the following areas: o Major activities involved in an EPC or FEED project. o Boiler operation, BMS and DCS logics, start-up, commissioning and troubleshooting of Desalination unit and Instrument Air Compressors.

o Pinch Analysis, Utilities Targeting, Heat integration Low temperature distillation and basics of Oil and Gas Processing from Masters in University of Manchester. Software Proficiency

• Proficient in ASPEN Plus, HYSYS and ASPEN Flarenet.

• Competent in all Microsoft Office Packages.

Educational Qualifications

• Master of Science in Advanced Chemical Engineering (Overall Grade 65%) University of Manchester, United Kingdom

September 2013 - September 2014

Core Modules include: Energy Systems, Utility Systems, Computer Aided Process Design, Oil and Gas Processing, Distillation Systems Design, Distributed and Renewable Energy Systems

• Bachelor of Technology in Chemical Engineering (CGPA 7.6) Anna University, Tamil Nadu, India

September 2009–May2013

Core Modules include: Heat Transfer Operations, Mass Transfer, Chemical Reaction Engineering, Transport Phenomena, Process Instrumentation and Dynamics Control, Energy Technology, Industrial Safety, Chemical Technology.

• ISC Level (12th Equivalent) (Total: 81%)

Hari Sri Vidya Nidhi School, Thrissur, Kerala, India June 2009

• ICSE Level (10th Equivalent) (Total: 82%)

Hari Sri Vidya Nidhi School, Thrissur, Kerala, India June 2007

Projects

Modelling and Analysis of Superheated Steam in Total Site systems M.Sc. Dissertation

June 2014 – September 2014

• The objective of the project was to maintain the required steam quality in a utility system taking into consideration the relative positions of the various components along a steam main and investigate operational variations.

• Simulations were carried out in ASPEN Plus to develop various retrofit models of the steam mains to achieve the targets. The targets to be achieved were set as steam turbine shaft work from a Base Case where it was considered that there are no heat losses in the steam main.

• Different cases were analysed by simulating heat losses in the steam mains as heat exchangers for different lengths of the pipe.

• Suggestions were made about the various constraints in future optimisation of utility systems where operational variations are considered.

Work Experience

1. Commissioning Engineer for Utilities and Offsites with Samsung Engineering

(ADNOC Carbon Black and Delayed Coker Project)

November 2015 to November 2018

Key Responsibilities

• Planning, co-ordination and tracking the progress of the commissioning activities.

• Worked in close co-ordination with project and construction department for achieving mechanical completion of various subsystems and actively involved in preparation and completion of Ready for Commissioning dossiers and certificates.

• Assuring that the work is carried out in compliance with the client requirements and policies and ensuring that relevant safety assessments and precautions have been taken before the activity.

• Take part in Mechanical Completion and PSSR (Pre Start-up Safety Review) walkthroughs.

• Actively involved in daily commissioning meetings and in discussions and presentations for start-up and commissioning of various units with client (ADNOC) and PMC (Jacobs).

• Involved in vendor coordination for Boiler dry out, boil out and passivation and for boiler start- up, operation and troubleshooting.

• Leader for start-up of Desalination Unit and Mechanical Run In Test of Instrument Air Compressors and Flare Gas Recovery Compressor (GARO). Involved in co-ordination with vendors for start-up and Commissioning and give proper direction and orders to field and DCS operators to follow the proper sequence of commissioning of the respective units.

• Checking of vendor and engineering documents with the actual site condition in co-ordination Engineering and Vendor.

• Preparation of all commissioning deliverables like: o Procedure for dry out and boil out of boiler.

o Mechanical Run in Test Procedures for pumps and Compressors (Instrument Air Compressor and Flare Gas Recovery (GARO) Compressor) o Solo Run Test procedures for Turbines

o Commissioning and Operating Manuals for all units in the utility system.

• Planning and identifying process loops and preparation of Mark-up P&IDs for leak test and inertization.

• Preparation and execution of LOTO system for introduction of commissioning fluids to the system.

2. Process Engineer with Samsung Engineering India (Noida, Uttar Pradesh) December 2018 to June 2020

Projects Handled

Key Responsibilities:

• Preparation of P&ID, PFD and PSFD diagrams as per client specifications.

• Performed Line hydraulic calculations for Pump, Compressor and Non pump loops, shut off pressure calculations and control valve sizing calculations

• Preparation of Equipment, Instrument and package process data sheets.

• Performed PSV sizing calculations as per API 520, 521 and 526.

• Used ASPEN Flarenet for flare header sizing calculations.

• Performed Vessel Sizing calculations as per Shell DEP.

• Performed Storage Tank sizing as per API 650 and tank in breathing and out breathing calculations as per API 2000.

• Preparation of documents like Operation Manual and Control Narratives.

• Performed Blowdown/depressurising calculations as per API 521 using Aspen HYSYS blowdown utility.

• Performed Vendor print review

• Preparation of technical queries and reports to clients and licensors.

• Coordination with other disciplines for query resolutions. Personal Details

Date of Birth 26th February 1991

Gender Male

Marital Status Single

Nationality Indian

Place of Birth Thrissur, Kerala, India

Linguistic abilities English, Hindi and Malayalam

Passport No J0457942

Email ID adehmo@r.postjobfree.com

Phone No +919*********

No Project Client Plant/Capacity

1.1.4111 1.

Long Son Petrochemicals

HDPE Project

Long Son

Petrochemicals

HDPE Plant

450 KT

2.

Bahrain Modernisation

Programme

Bahrain Petroleum

Company

Utilities, Offsites and Sulphur

Block

3.

Carbon Black and Delayed

Coker Project

ADNOC

40,000 tonnes of Carbon

Black and 4,30,000 tonnes of

calcined coke

4.

Hawiyah Unazyah Gas

Reservoir Storage Project

Saudi Aramco

1500 MMSCFD gas injection

facility and 2000 MMSCFD

gas reprocessing facility

5.

Onshore Gas Plant for

Rosmari Marjoram Project

Sarawak Shell

800 million cubic feet gas

processing

Contact this candidate