Reginald Smithers

CNC Machinist/ Inspector

New Waverly, TX 77358

addke3@r.postjobfree.com

832-***-****

Responsible for examining and inspecting materials and parts to discover defects, wear, and tear. Work Experience

Machinist/ Inspector

UNITED MACHINE WORKS - New Waverly, TX

February 2019 to August 2019

• Operated Puma Machine

• Read and interpret blue prints make parts to specified tolerances within .0005.

• Own my own tools

• Capable of indicating parts in a 3 jaw or 4 jaw chuck

• Performed set ups,edit M and G code programs, Perform quality check on first article

• Inspect materials and finished parts.

• Determine if product or parts is in conformance with specifications.

• Adjust process or assembly equipment

• Collect samples for testing

• Read and adjust dials

• Marks items for acceptance or rejections

• Pull faulty products off productions line

CNC Machinist

Conroe Machine

June 2018 to November 2018

Operate Puma machine.

Conduct preventive maintenance on machines.

Dial in vises, stops, and fixtures on machine table using indicator, select appropriate tools for job, touch tools off, change dull worn inserts when needed, calculate appropriate speeds and feeds to get max life from tools.

Read and interpret blue prints make parts to specified tolerances within .0005 Own my own tools, 6 &12-inch calipers, 0-4-inch micrometers, dial test indicator, back push button indicators, precision right angle square, and all other hand tools commonly used in machining. Analyzed part blue print and determine best way to make production run. Come up with fixture design ideas when necessary.

Manual Machinist

Lamon's Gasket & Seals - Houston, TX

September 2017 to June 2018

Perform machining operations on manuals lathes. Operate Kingston. Turn the outside diameter of round bars; From 2" to 5" to specific close tolerance; plus/minus0.005" Capable of indicating parts in 3 jaw chucks on hollow spindle and engine lathe. Able to machine contours, bevels and angles per prints or instructions. Reads and understands blueprints.

Owns hand tools plus indicators, measuring rules and tapes and OD and ID micrometers. Manual Machinist

Jyoti Americas - Conroe, TX

May 2016 to March 2017

Measured and marked dimensions and reference points accurately. Measured instruments to verify compliance with precise specifications. Dismantled and inspected components and adjusted and repaired them as necessary. Machined small and large parts to tolerances of 1 or less. Calculated and set controls to regulate machining factors like part speed, feed, coolant flow, depth and angle of and clamping methods.

Security Officer

US Security Associates Inc - Houston, TX

September 2015 to February 2016

Called police or fire departments in cases of emergency, such as fire or presence of unauthorized persons.

Answered alarms and investigate disturbances

Observed activity and traffic in assigned areas to enforce rules/regulations. Wrote reports of hourly activities and irregularities, such as equipment or property damage, theft, presence of unauthorized persons, or unusual occurrences. Patrolled assigned site on foot or in vehicle; checks for unsafe conditions, hazards, security violations, blocked entrances and exits, and unauthorized persons. CNC Machinist

Weatherford International - Drilling Services - Huntsville, TX February 2014 to March 2015

Performed part set ups, write and or edit M and G code programs, perform quality check on first article and every twenty parts after for quality assurance using calipers, height gauge, micrometers, depth gauges, and gauge pins. Conduct preventive maintenance on machines. Dial in vises, stops, and fixtures on machine table using indicator, select appropriate tools for job, touch tools off, change dull worn inserts when needed, calculate appropriate speeds and feeds to get max life from tools.

Read and interpret blue prints make parts to specified tolerances within .0005 Own my own tools, 6 &12-inch calipers, 0-4-inch micrometers, dial test indicator, back push button indicators, precision right angle square, and all other hand tools commonly used in machining. Operate manual mills and lathes. CNC Fanuc controlled mills and lathes. Analyzed part blue print and determine best way to make production run. Come up with fixture design ideas when necessary.

Boring Machinist

Energy Alloys - Conroe, TX

October 2013 to January 2014

Measured dimensions of tools using instruments like Vernier calipers and micrometers screw gauge. Aligned cutting tools and accessories onto machines. Produced machine tools using lathes and grinders as per specifications. Examined machines for defective parts and dismantle machines. Responsible for assembling parts and fitting them. Checked competed work pieces for quality and ensure their lubrication. CNC Machinist

Downhole Drilling Dynamics - New Waverly, TX

June 2011 to November 2012

Worked directly from blueprints, patterns, sketches and specification Operated heavy duty lathes, boring machines, mills, and grinders Moved pallets of heavy raw materials from the material staging area to the CNC machines with a forklift

Able to use precision measuring instruments, for example: OD mics, Dial calipers, Digital calipers, Blade micrometers, and various other measuring instruments Able to run various machines with Fanuc controls, such as: HAAS, and Mori Seiki. Able to make program changes to all the machines mentioned above. Education

High school Diploma

Technical School - Conroe, TX

Jack Yates High School - Houston, TX

Skills

• Cnc Lathe

• CNC

• Blueprint

• Inspection

Contact this candidate