FERDINAND C. CORPUZ

Resume

Gas Turbine

Steam Turbine

HRSG Steam Generator

Diesel Generator

BSDG

Balance of Plant BOP

Water treatment Plant

Rotating Equipment’s

UPS

SCADA, DCS board operation

Soft Starter

VFD

HV and LV Switch Gear

Power Transformers

Air compressor

HVAC

Capacitor Bank

Battery Charger

Education

Registered Electrical Engineer No.

0015845 Philippine Professional

Regulation Commission.

BS Electrical Engineering Holy Angel

University. 1984-1989

Industrial Electricity. Holy Angel

University. 1983-1984

Computer Training Course MS Office,

MS word, MS Excel, basic Auto cad,

power point, paint.

Personal Skills & Key Attributes

Communication

Ability to Work under pressure.

Independent decision

Conflict resolution.

Team work

Creativity

Data Analysis

Event planning

Public relation.

Electrical Hazard Awareness

Electrical System

Electric, Instrument & Controls

Problem Solving

Team Leadership

Preventive Maintenance

Troubleshooting

Verbal and Written Communication

Profile Summary

Over 18 years of experience in Power and Water Generation, Oil & Gas, Commissioning, Testing, Start-up Operation and maintenance of Steam and Gas Turbine / Combine Cycle Power Plant and desalination projects in Middle East and North Africa, Coal Fired Thermal Power Plant in Turkey, Vietnam, and Philippines and Oil and Gas in Kuwait, Qatar, LNG in Algeria. PTW, H2S, SCBA and Authorized Gas testing and safety training oriented a multi skilled maintenance engineer (electrical & mechanical) Responsibility

Provide engineering and technical supports to all the electrical work groups at site

Operation switching change-over of transformers, MV/LV switchgears prior to Maintenance.

Trouble shooting and maintenance of MV/LV Switchgear and motors.

Protection relays settings and calculation.

Installs, repairs, and maintains motors, transformers, generators,

Studies plans, drawings, specifications, and work orders to determine work requirement and sequence of repairs and/or installations.

Well familiar with protection concepts and working knowledge in potentially hazardous area.

Coordinate and provide technical assistance to SCADA Engineers, Substation Physical Engineers, and control design staff in order to fully develop system integration of protection, control, and monitoring system.

Work permit system and attended various fire and safety training conducted by QG, KOC.

Directly responsible for the safety of all electrical groups’ personnel of the project by ensuring that the project execution will be done according to all applicable health, safety, sanitary and environmental standards.

To help develop operational procedures for the designated areas.

Participates in regular meetings with Construction team for Pre-Commissioning & Commissioning activities.

Perform work order as application of full SAP duties Presently Working Experience

TOTAL YEARS EXPERIENCE: 18 YEARS

IN MIDDLE EAST & Africa: 12 YEARS

IN Philippines: 06 YEARS

Presently Working Experience

03 Mar 2018 - 30 Nov 2019: Electrical Engineer/Commissioning/O&M/QA/QC Company: Schlumberger Oilfield Eastern LTD

Client & Site: Kuwait Oil Company (KOC)

Jurassic Production Facility (JPF-2) at East Raudhatain Nature of Work:

Generally responsible of monitoring of all electrical related works at site.

Provide engineering and technical supports to all the electrical work groups at site.

Coordinates with Client / Consultant’s representatives for any site instructions and inspection of works.

Responsible for the monitoring and makes necessary actions to sustain continuous and safe operation of the Substations.

Act as lead engineer for testing and commissioning activities and recording results.

Understand and implement the Commissioning Strategy. 2 P a g e

Schlumberger-Private

04 April 2017 –30 Dec 2017: Operation Shift Leader Client & Site: EVN Vietnam Electricity National Power Corporation Thai Binh Thermal Power Plant Project

300 MW X 2 Units, Coal-Fire Thermal Power Plant

Thai Binh, Vietnam.

Company: Marubeni Corp & Fuji Electric Co. LTD

Nature of Work:

Work as Shift Leader under overall Commissioning Management Team.

Prepare a plan of Shift Operation.

Supervise and oversee daily plant operations and maintenance in the operation shift team in order to ensure that operational targets are achieved safely, efficiently and within the company rules and procedure, OEM guidelines, legal, environmental, contractual and other requirements.

Training

HSE Company rules

PTW

H2S

SCBA

Fire fighting

Basic first aid and CPR

HV/LV Switching

LOTO

Reference

A. Rafael Petros Kaldani - Protechpps

Managing Director General Trading &

contracting Co. WII, Kuwait

B. Andrew Jenkins - Protechpps

Managing Director General Trading

& contracting Co. WII, Kuwait.

C. Ian D. Royal- Site Manager SPIE Oil

& Gas services,

addgo0@r.postjobfree.com

D. Nishioka Takanori - Project Engineer,

addgo0@r.postjobfree.com IHI

Power Plant Division.

E. Yugi Gomi - DCS Engineer,

addgo0@r.postjobfree.com IHI Power Plant

Division

Develop and write Commissioning Test documents based on contract documents and relevant governing codes of standard and regulation.

Manage reporting and close out of Commissioning deficiencies.

Monitor installation of electrical system conformance to contract drawings to assist quality control and commissioning team.

Monitor design changes issued by consultants and ensure they are captured on-site and in Commissioning documentation.

Ensuring construction work complies with all Engineering Standards, codes, specification and design instruction.

Attend daily meetings to update client. Compiling system/sub system ITR’S paperwork as required.

To undertake fault finding and diagnostic activities including fault rectification.

Assign targets for accomplishments and ensure targets are met on daily basis for all electrical groups at site.

Performs other related duties as may be required by the project site Manager.

Directly responsible for the safety of all electrical groups’ personnel of the project by ensuring that the project execution will be done according to all applicable health, safety, sanitary and environmental standards.

To help develop operational procedures for the designated areas.

To contribute to ensuring pre commissioning/commissioning activities. Punch listing.

Ensure that all activities in the day-to-day operation are carried out in a manner safe for personnel and equipment and minimizing the impact on the environment.

General housekeeping, isolation and preparation of equipment for maintenance.

Preparation, start-up, parallel and changeover of generators.

Establish and maintain knowledge of relevant technical standards and legislation.

Plan and execute inspections and monitor all Electrical Pre-Commissioning activities, Loop Checking.

Responsible for operation and maintenance and switching operation of GTG 3.3KV/0.4KV at Substations and ATS Changeover of HV/LV SWGR and Transformers.

Participates in regular meetings with Construction team for Pre-Commissioning & Commissioning activities.

Ability to work within a multi-disciplinary team to achieve successful installation and Commissioning of major projects.

Participates in raising of non-conformance report/corrective action required /Defects or Punch-list items. Prepares and manages system Punch-lists, monitors defect rectification, liaises with Commissioning Team to achieve safe and timely start-up of facilities.

Reports to the E&I Site Superintendent or E&I Project Engineer as appropriate.

QA/QC of the Electrical, as per the Project Specification and requirements.

Carry out any non-contractor obligation ATEX inspections as per Project requirements.

Act as a third-party inspectorate, sample checking contractor and vendor ATEX inspections to ensure compliance.

Ensuring that Contractors / Sub-Contractors comply with the QA/QC requirements, testing and reporting as per the Project Standards and Requirements.

Ensure all work, tests and inspections undertaken by Contractor is in accordance with the Specifications/Contract Requirements and signs the relevant Test Certificates.

Reviews Contractor and Vendor QA/QC Documentation and design deliverable and confirms accordance with relevant International and Project Specifications.

To implement and ensure Quality Assurance and Quality Control in the field of Electrical, Instrumentation as per the Project requirements, Project Specifications, Standards and Codes.

To ensure that the Contractor / Sub-Contractor follow the project quality requirements during the construction of project.

Project Specification: EPF Facility at East Raudhatain Based onshore on new facility (EPF) early production facility, Plant consisting of VRU / MRU / SRU/ CRUDE / SOUR GAS, 2 x MV/LV Sub stations / Central control room / 4 LER’S (Local Equipment Room), 4x 4MW solar turbines 3.3KV/440v switchgear / AC/DC UPS systems / HV/LV drives VFD / Soft starters / HVAC. 3 P a g e

Schlumberger-Private

Responsible for the safe, reliable and efficient operation including start-up and shutdown of Power Plant, Steam turbine, balance of plant equipment and its auxiliaries in accordance with the plant policies, Operation Department, policies, or other task directed by the Shift Superintendent, Shift Supervisor.

Assist to establish the appropriate procedures and computerized maintenance management processes as applicable to a prudent operation management, the permit to work system.

Operate the plant safely in line with the requirements of National Dispatch.

Continuously improve systems and procedures based on experience.

Understands and adheres to all Plant Safety Guidelines and Procedures.

Strives to maintain an injury-free environment.

Understands and masters the Plant Emergency Handling Procedures.

Ensures control of the plant process and electrical distribution through the plant Distributed Control System (DCS) and other process control devices.

Assists in scheduling daily maintenance actions, plant configuration changes and varying power generation levels.

Monitors plant chemistry and chemicals handling.

Identifies problems with plant equipment and clearly communicates the conditions associated with these problems to the Shift Engineer / Plant Maintenance Team.

Ensures the completion of shift round checklists, routine daily/weekly/monthly test checklists and equipment change-over checklists, etc.

Responsible for the generation and sending the Plant’s daily data requirements in a timely manner to all applicable parties.

Operate the control system of the power plant substation equipment and HV/LV switchgear during plant maintenance activities, emergency situations or as required.

Assist in the implementation of company policies, safety procedures (proper “Lock-out/Tag-out” procedures and other safety procedures), good housekeeping, energy conservation guidelines and environmental regulation. Project Specifications: 1. Boiler: Amec Poster Wheeler, 2. STG: Fuji Electric Co, LTD. 3. FGD: Kawasaki. Specification: Pulverized coal arch fired, Anthracite firing, Natural Circulation Reheat Steam Generator, MSP:16.67MPa, MST:540deg, RHST: 538deg.RHSP: 4.011MPa, Exhaust Press: 6.5KPa, Steam Turbine: Rated Out Put: 300MW, 3000RPM, Reaction reheat Condensing Type. 01 March 2016 –30 March 2017: Operation Shift Engineer Client & Site: MPC Mindanao Power Corporation

Balingasag,3x 55MW Coal Thermal Power Project.

Misamis, Oriental, Philippines

Company: MITSUBISHI CORPORATION

Nature of Work:

Work as Shift Leader under overall Commissioning Management Team.

Prepare a plan of Shift Operation.

Supervise and oversee daily plant operations and maintenance in the operation shift team in order to ensure that operational targets are achieved safely, efficiently and within the company rules and procedure, OEM guidelines, legal, environmental, contractual and other requirements.

Responsible for the safe, reliable and efficient operation including start-up and shutdown of Power Plant, Steam turbine, balance of plant equipment and its auxiliaries in accordance with the plant policies, Operation Department, policies, or other task directed by the Shift Superintendent, Shift Supervisor.

Assist to establish the appropriate procedures and computerized maintenance management processes as applicable to a prudent operation management, permit to work system.

Operate the plant safely in line with the requirements of National Dispatch.

Continuously improve systems and procedures based on experience.

Understands and adheres to all Plant Safety Guidelines and Procedures.

Strives to maintain an injury-free environment.

Understands and masters the Plant Emergency Handling Procedures.

Ensures control of the plant process and electrical distribution through the plant Distributed Control System (DCS) and other process control devices.

Assists in scheduling daily maintenance actions, plant configuration changes and varying power generation levels.

Monitors plant chemistry and chemicals handling.

Identifies problems with plant equipment and clearly communicates the conditions associated with these problems to the Shift Engineer / Plant Maintenance Team.

Ensures the completion of shift round checklists, routine daily/weekly/monthly test checklists and equipment change-over checklists, etc.

Responsible for the generation and sending the Plant’s daily data requirements in a timely manner to all applicable parties.

Operate the control system of the power plant substation equipment and HV/LV switchgear during plant maintenance activities, emergency situations or as required.

Assist in the implementation of company policies, safety procedures (proper “Lock-out/Tag-out” procedures and other safety procedures), good housekeeping, energy conservation guidelines and environmental regulation. Project Specifications: GE Steam Turbine Generator with a base load capacity of 55 MW (3 units a Circulating Fluidized Bed Combustion Boiler capacity of 220 Tons per hour of superheated steam capacity and 520 C reheated steam, comprises of 2 hot gas generator bed firing start up burners with both HFO and LFO injection.

18 Feb 2015 – 28 Feb 2016: Electrical Commissioning Engineer Client & Site: ENERJISA ENERGY GENERATION INC.

Tufanbeyli lignite Coal Thermal Power Plant

Tufanbeyli Town, Adana Province Republic of Turkey Company: SK ENGINEERING & CONSTRUCTION

Nature of Work:

Assigned for the commissioning of the 3 x 150 MW Thermal Power Plant (coal fired) project handling commissioning jobs and activities for Circulating Fluidized Bed Combustion Boiler and its auxiliaries such as combined induced draft fans, primary and secondary air fans, hot cyclone 4 P a g e

Schlumberger-Private

and loop seal air blowers limestone slurry preparation system and auxiliaries coal handling and fly ash handling system, condensate system with condensate air removal, Gland Steam Condenser, LP and HP Feed water Air Heaters and condensate polishing plant, dry cooling system, electrostatic precipitator, selective non-catalytic reduction (SNCR)system, Flue Gas Desulfurization System with absorber recirculation pumps and ME Washing Water Pumps, Circulating Water Pumps with Recovery Turbine and Water Treatment Plant & Waste Water Treatment System.

Test and Commissioning of ABB 6.3kV – 400 V MEDIUM VOLTAGE SWITCHGEAR including MICOM (Schneider) Multi-function Protection Relay.

Commissioning of ABB Low Voltage Switchgear including Vacuum Circuit Breaker (VD4 VCB).

Commissioning of 6.3KV/ 400V MCC (Motor Control Center) of Control building and Industrial System.

Responsible for the preparation for the following commissioning check sheets and do an internal and initial test prior for the preparation of the functional Test which is given a request notification to the client one day before the function test of the system.

Pre-commissioning works and inspection of all electrical and instrumentation packages, loop checking, inspection of equipment ensuring compliance to industry standards.

Testing and commissioning of all the motors and pumps in the entire plant.

Review Electrical commissioning plans, prepare/formulate commissioning procedures and other documents for CFBC Boiler System and auxiliaries, and BOP Systems which include; Limestone Slurry Preparation System, Circulating Water System, Water Treatment System, Dry Cooling Tower System, FGD System, Sump Pump System, HFO and LFO System, PA and SA System, Raw Water System, Service & DM Distribution Water System, Feed water System, Condensate System, Coal Handling and Fly Ash Handling System, ESP System, Soot blowing System, Limestone Transfer and Limestone Slurry Preparation System and Waste Water and Sewage Treatment System.

Perform system walk down & prepare punch and remaining items in plant. Project Specifications: Siemens Steam Turbine Generator with a base load capacity of 450 MW (3 units a Circulating Fluidized Bed Combustion Boiler capacity of 463 Tons per hour of superheated steam capacity and 424 tons per hour reheated steam, comprises of 8 burner bed firing start up with both HFO and LFO injection.

01 April 2014 – 30 Aug 2014: Operation & Maintenance Coordinator Client & Site: N/KOM Nakilat Keppel’s Offshore & Marine Ras Laffan Ship Yard Facility Project, Doha, Qatar Company: SPIE Oil & Gas Services

Nature of Work:

Responsible for continuously monitoring the Plant’s critical streams to ensure balanced operation rates and optimum operation.

Responsible switching operation of RMU’s in 34 unit of substations 33KV/11KV Offshore & Onshore in HV/LV SWGR during emergency and preventive maintenance shutdown to interchange the open point and return back after completion of work.

Provide maintenance and troubleshooting assistance in engineering facilities and issues safe PTW system.

Liaise between operations control rooms during sequential start-ups, shutdowns and emergencies.

Ensure clear guidelines are delivered to manage and reduce negative impact during power interruptions or emergencies.

Investigate quality defects for root cause and help improve manufacturing system efficiency.

Monitor productivity and activities to ensure they are compliant with the Environmental, Health and Safety (EHS) guidelines.

Relay production constraints to appropriate business and planning organization to provide accurate input to production plan.

Develop and maintain log sheets, equipment checklist, and other tools to track operation and maintenance.

Submits KPI monthly report and site daily reports, inspection requests, estimates and all applicable monitoring reports on regular basis or as required. Keep equipment operational by coordinating maintenance and repair services; following manufacturer’s instructions and established procedures.

Ensure adherence to all applicable regulations, policies and procedures for health, safety and environmental compliance.

Experience with contractors and worldwide suppliers, those involved in the construction of major oil and gas facilities.

Maintain professional and technical knowledge by attending educational workshops; reviewing professional publications; establishing personal networks and participating in professional societies.

Perform any job-related activities as requested immediate by the manager. 21 April 2012 – 01 April 2014: Electrical Engineer Client & Site: N/KOM Nakilat Keppel’s Offshore & Marine Ras Laffan Ship Yard Facility Project, Doha, Qatar Company: SPIE Oil & Gas Services

Nature of Work:

Generally responsible for implementations of Method of Statement and monitoring of all electrical related works at site.

Manages directly and provide engineering and technical supports to all the electrical work groups at site.

Coordinates with Client / Consultant’s representatives for any site instructions and inspection of works.

Attending meeting with Clients and Colleagues to get a comprehensive understanding of any project specific needs. Performed preventive maintenance and operation of the 3 Units Motor Generator, Motor 1500KW, 4160V,60HZ and Generator 1500KVA,11KV, 60HZ, with common grounding resistor; & VSDS converter.

Responsible for operation and maintenance and switching operation of Ring Main Unit (RMU) 11KV of 34 Substations 11KV/440V, ATS Changeover of HV/LV SWGR, Transformers, Capacitor Bank, Battery Charger, Battery Bank, Cathodic protection.

Performed Commissioning protection test and trip test of Transformers, HV Switchgear, ACB, MCCB using a PRO10/T & TT1 ABB testing instrument.

Responsible for the monitoring and makes necessary actions to sustain continuous and safe operation of the Substations.

Develop and maintain log sheets, equipment checklist, and other tools to track operation and maintenance.

To undertake fault finding and diagnostic activities including fault rectification.

Estimates, prepares and assigns the resources such as manpower, materials, consumables, equipment, tools, etc., required for all electrical and related works prior to execution.

Plans the execution of all electrical related works and coordinates the to end users.

Assign targets for accomplishments and ensure targets are met on daily basis for all electrical groups at site. 5 P a g e

Schlumberger-Private

Submits KPI monthly report and site daily reports, inspection requests, estimates and all applicable monitoring reports on regular basis or as required.

Performs other related duties as may be required by the project site Manager.

Directly responsible for the safety of all electrical groups’ personnel of the project by ensuring that the project execution will be done according to all applicable health, safety, sanitary and environmental standards.

To help develop operational procedures for the designated areas.

To contribute to ensuring pre commissioning/commissioning activities.

Punch listing.

Ensure that all activities in the day-to-day operation are carried out in a manner safe for personnel and equipment and minimizing the impact on the environment.

General housekeeping, isolation and preparation of equipment for maintenance. 20 April 2011 – 20 April 2012: Electrical Engineer Client & Site: QP RasLaffan Port Expansion Project Doha, Qatar Company: SPIE Oil & Gas Services

Nature of Work:

Develop and administer pre functional and functional test of equipment’s such as: Water distribution systems, pumps, normal and standby electrical distribution systems, UPS, standby generators, and emergency lighting.

(Pre)-commission & start-up facilities motor and pumps from medium11KV to low voltage 430V ensuring test procedures are implemented check rotation, vibration, starting and running current, acceptance criteria are met and passed on to client.

Prepare permit to work and other safety permits and acquire appropriate approvals.

Preventive maintenance of Electrical panels HV & LV SWGR, GUTOR & CHLORIDE UPS battery chargers and dual inverters.

Develop and maintain commissioning logs, equipment checklist, and other tools to track commissioning.

Projects perform scheduled walk through of construction sites.

Assist with field troubleshooting of commissioned equipment.

Schedule and direct periodic commissioning meetings.

Interface with clients, contractors, equipment vendors and owners’ agents.

Switching of Electrical System, ATS operation of 33KV to 11KV SWGR from primary to tertiary substation RMU, main transformer & auxiliary transformer 400MVA,132KV/33KV/11KV/(3.3KV).

To undertake fault finding and diagnostic activities including fault rectification.

Technical knowledge relating to the electrical and safety aspects of substation plant with fault findings.

To eliminate accidents and near misses by adopting risk assessment techniques, being aware of potential hazards.

To act as a role model for staff, promoting safety awareness within a team, promoting the reporting and close -out of injuries, incidents and near misses. To provide mentoring and/or training to other members of staff.

Experience in substations work and/or on HV cable systems, encompassing electrical, mechanical, and telecoms engineering disciplines.

Perform work order as application of full SAP duties. 31 July 2009 – 28 Feb 2011: Operation Shift Engineer / Electrical Commissioning Client & Site: General Electricity Company of Libya GECOL Benghazi Combine Cycle Project (BCCP)

2X 287 MW & STG 250 MW

Company: DAEWOO E&C

Nature of Work:

Fully in charge of power plant operations for duration of duty period.

Manage and lead Operations Shift Group, closely monitoring the operational parameters and issues safe PTW system.

Take necessary action to prevent equipment failure, respond to alarms by taking appropriate corrective actions and execute plant shut-down and start-up procedures as required.

In conjunction with Operations Superintendent ensuring the safe, reliable, environmentally and commercially efficient operation of the plant.

Develop system scoping documents testing procedure and reports.

Makes necessary adjustments based on operating conditions and maintains a variety of record such as oil/gas flow, temperature, pressure etc. Carries out routine maintenance on all plants and equipment and participates in isolating plants/equipment for major maintenance.

Regulates the voltage and frequency, and controls active and reactive power flow in the network.

Monitor and adjust production processes or equipment to ensure quality efficiency and productivity.

Assure that the plant meets requirements while operating in a safe and efficient manner.

Prepare permit to work and other safety permits and acquire appropriate approvals.

Supervise of Operation in DCS system. Monitor plant equipment from the control room; identify abnormal conditions, diagnosis problems and take corrective action when needed.

Directs the switching operations by giving instructions to field engineers in carrying-out switching in the 400kV, 220kV, 20kV and 10.5kV primary substations for maintenance and repair of network components, and for after fault restorations conforming all operations done in strict compliance with department safety rules and regulations giving priority to safety and security.

Issues safety documents for works in the field ensuring proper isolation and ear thing.

Full involvement in the EPC phase of the Power Plant including mechanical completion and commissioning.

Work closely with client site personnel and vendor service engineers engaged in pre-commissioning activities such as Commissioning and Start- up of SIEMENS 287MW STG5-4000F Gas Turbine Units1,2.

Commissioning of Electrical System, Functional test protection circuit of auto Transformer, main transformer & auxiliary transformer 400MVA,400/220/ (10. KV)/240-300MVA, 400/20KV/18.75-25MVA,20/10.5KV.

Commissioning of 10KV Medium voltage and 400V low voltage switchgear functional test. Including SIPROTEC 7SJ62 (Siemens) Multi-function Protection Relay and ABB SUE3000 Auto Bus Transfer.

Commissioning of Generator Circuit Breaker (GCB) ABB HECS 100L T type for Steam and Gas Turbine Generator with the ABB vendor supervisor.

6 P a g e

Schlumberger-Private

Commissioning of Steam turbine and Generator protection GPR, TGR, TPR AVR and EHG with Fuji Vendors.

(Pre)-commission & start-up facilities motor and pumps form medium10KV to low voltage 400V ensuring test procedures are implemented check rotation, vibration, starting and running current, acceptance criteria are met and passed on to client.

Review engineering drawings and specifications to ensure adequate provisions have been made for testing and other pre-commissioning functions.

Able to perform and solve any unexpected problem happen in time of commissioning period.

Supervise construction craft labor assigned him. May administer on safety and clearance tagging procedure.

May supervise and direct an operational shift as the facility progresses through commissioning and testing.

Informs management about important events and abnormalities. 28 Feb 2009 – 30 July 2009: Warranty Engineer

Client & Site: General Electricity Company of Libya GECOL Benghazi North Combine Cycle Project (BNCCPP) Libya 4X 149.5 MW, 2STG X 153.25 MW

Company: DAEWOO E&C

Nature of Work:

Preparation of inspection and maintenance work

Follow-up of operation of the Plant (production, maintenance, inspection)

Follow-up of reliability

Issued weekly report to managers and stating the operating condition of the plant.

Attend meeting with GECOL (General Electricity Company of Libya) regarding the warranty up-date logs.

Supervision of maintenance tasks such as repair plant instrumentation and electrical circuits; assisting in troubleshooting and inspecting programmable logic controllers, including control card replacement and wiring terminations; and reading and interpreting mechanical drawings, electrical one-lines, logic drawings, technical manuals and P&ID's, write routine reports, solve practical problems.

Start-up/shutdown and normal operations of power stations; installation, maintenance, testing and/or operation of gas turbine driven generators, transformers, pumps, motors, Diesel Gen-set, batteries, battery chargers, PLC, 400kV indoor/outdoor substations, switch boards, oil/vacuum / SF6 gas insulated circuit breakers etc.

The Plant is composed of four (4) existing Gas Turbines and Generators, four (4) new Heat Recovery Steam Generators, two (2) new

Contact this candidate