Michael D. Callahan

615-***-****

*** **** ****** ****

Cotton town TN. 37048

adbur4@r.postjobfree.com

Skills: Multi-tasked

Self- starter; requires little direction

Microsoft OS, Microsoft office, Microsoft Power Point, Excel and Internet

OSHA 10 CERTIFICATION

EXPERIENCE:

1/2/2018 to 2/12/2020 TRADESMEN INTERNATIONAL Nashville TN.

CONSTRUCTION Electrical Installation

Cut-in light switches boxes install and secure at 44-inch code

Cut-in plugs boxes install and secure 18-inch code

Drill holes and drag or drive wiring throughout openings

METRO lighting installation remove and replace all lightings

Bending and installing conduit and raceways

Mounting control panels and electrical devices

Pull 120/208 volt MC wires, which is used to power 120 volt plug loads

Mount lighting fixtures, ceiling fans, install plugs, switches

Assist the electrician with installing wiring, lights, and plug-in sockets

Connect whips from junction boxes to plug boxes and light switch boxes 18” and 44” to center

Termite high voltage and low voltage panels

Replacing light fixtures all bulbs

7/14 to 12/12 2017 Empower Electric, LLC Nashville TN

CONSTRUCTION ELECTRICIAN

Pull MC wires for all home runs to electrical room, Single/ three phase 120V. 2/3 wire

Pull 120/208 volt MC wires, which is used to power 120 volt plug loads

Make all circuits connections in to electrical panel black/white/green = Lights/Plugs

Brown/orange/yellow/gray (BOY) for 277/480V = three phase

Install 277/480 volt MC wires used to power single phase 277 volt lighting and larger HVAC loads

Mount junction boxes install home runs strap to ceiling with Concrete & Steel Powder Nail guns

Install whips to plug boxes and switch boxes wire nut all wires and install mud ring and face plates

Mount and secure light fixtures connect electric wires

Connect whips from junction boxes to plug boxes and light switch boxes 18” and 44” to center

Connect appropriate circuit wires to breakers in electrical room/panel

Breakers installation 20amp.= lights, 30amps = Heater, 50amps= ovens, 70/100amps= HVAC

Conduit ”, 3/4” 1” measure cut and install to boxes panels

Bend conduits 90’ stub up, box offset, other offsets 3 point saddles, 4 point saddles, back to back 90

Strap conduits Race way 3’ less between two boxes, 5’ between termination of 10’

Mount lighting fixtures, ceiling fans, install plugs, switches

120V TO 20AMP BREAKERS 240VOLTS TO 30/50AMP BREAKES

TROUBLESHOOT ELECTRICIAL PROBLEMS

9/12 to 7/14 CCS CONSTRUCTION Nashville TN

CONSTRUCTION Electrician TOP Helper

Assist the electrician with installing wiring, lights, and plug-in sockets in residential houses

Examine electrical units for loose connections and out of order insulation and make connections tighter, using hand tools.

Strip insulation from wire ends, by means of wire stripping pliers, and fasten wires to terminals for later soldering.

Disassemble faulty electrical equipment, change flawed or damaged parts, and mend equipment, by means of hand tools.

Carry tools, materials, equipment, and supplies to work site physically.

Thread medium ends, attach couplings, and put together and secure medium support brackets

Drill holes and drag or drive wiring throughout openings

Find short circuits in wiring with test meter.

Determine, cut, and turn wire and conduit

Preserve tools, vehicles, and utensils and keep parts and supplies in order

Pull wires through conduit leading to connection boxes, switch panels, and other terminals.

Replace faulty circuit breakers, fuses, switches, electrical and electronic components, or wire.

Construct controllers and panels, using power drills, drill presses, taps, saws and punches.

Bend 1/2, 3/4 and 1 inch conduit to various shapes install and pull wires

Wired a single family home, saving the client a huge amount of expense.

11/00 to 9/12 Ford Lincoln Mercury Queens NY

BODYSHOP OPERATION BODY WORK AND PAINTING

HEAVY COLLISION REPAIRS, FRAME, UNIBODY STRAIGHTING

Weld and repair broken parts using miller mig welders’ grind sand prime and paint

9/93 to 11/00 Metered Appliance Co. Queens, NY

Laundry washer/Dryers Assembly & Repairs Supervisor

Assembly all washing machines and dryers parts and electrical components

Assembly all washing machines and dryers parts and electrical components

Assembly new mechanical and electrical parts

INSTALL NEW ELECTRICAL HOMERUN J-BOX MC 12/2 WIRE

BENG 12” to ” CONDUIT MAKE UP BOXES INSTALL BREAKER

CONNECT ALL WIRES TO PANNEL AND WASHERS & DRYERS

Install washer drain pumps

Remove and replace new water pumps

Install wire harness following drawings

Remove and install coin slots with credit card readers

Install money dispenser for credit cards

Perform quality checks on products for Mechanical and Electrical parts.

Review work orders and blueprints to ensure work is performed according to specifications

Install washing machines and dryers connect all electrical switches and electrical cords

Trouble shooting manufacturing equipment issues as well as making

Trouble shoot and install 120 V & 240 V Electrical wires and breakers

Used all Types of pneumatic powered tools and Electrical power tools & Measuring Tapes.

EDUCATION/TRAINING Apprenticeship Awards

Queens College Georgetown Guyana S.A. Automotive

Guyana Technical Trade School

General Certificate of Education

High School Diploma

Valid NYS/TNS Security Guard License, TNS Driver License

OSHA 10 CERTIFICATION

Contact this candidate