** ***** **** **** ******** Mass *****

Phone 339-***-****

Bleyden@comcast,net

William P Leyden

Objective

Skills

Professional experience

To secure a challenging position as a Senior Level Engineering Technician utilizing my practical knowledge, demonstrated skills and unique abilities to further my career opportunities.

Electro mechanical Assembly And Optical alignments. Troubleshooting and repairing circuit boards

Digital and analog test experience.

Outside Parts Procurement

Manufacturing and Documenting cable harnesses

Proficient in soldering and component replacement

Operation of machine shop equipment

Medical Device Assembly Experience

Physical Sciences Inc.

Andover Mass.

Electromechanical Technician/Test Technician

01/28/2019 – Present

Worked in the Radiation Sensor Division on 3 main products: Radiation Monitors, Mobile Radiation detection in the back of a Chevy Tahoe and Perm Mobile highly configurable solution for Mobile and Static Application:

Crystal heaters and temperature installation wiring.

MURS Gamma Module assembly battery and chassis wiring and installation.

Foam Insulation around entire unit and Install outside cover.

Cytonome LLC

Bedford Mass

Electromechanical Technician/Test Technician

11/1/2016 – 01/19/2019

Responsible for Genesis III and taking new Viva bench top Cell sorter from Engineering to Manufacturing . My duties also included board testing and building Electronic sub-assemblies cable wiring and installing into Chassis and final system testing.

Board Testing consisted of on board programming individual active testing and minimal 4 hour burn-in process to ensure 98% throughput.

Red line assembly improvements to streamline manufacturing process.

Submit engineering changes to next level of support for evaluation.

Use Omnify in house inventory system to track all units through each stage of manufacturing.

L-3 Henschel Navigation & Communication

Ayer Mass

Electromechanical Technician/ Test Technician

11/15/2014 – 11/1/2016

* Assembled Ship Control Consoles for all ship

Bridges.

Worked on Integrated Bridge Navigation Systems

Built Ships Control and Display System. Ships Course Indicators and Rudder Angle indicators and shaft speed indicators with rpm and pitch.

Navigation Data Distribution and all internal phones and data security Systems throughout entire ship Pelorus Stands and all Speed indicators.

Qinetiq North America Waltham, Mass

Electromechanical Technician II

03/01/2010 – 11/08/2014

Worked on all the command and control Instrumentation on the new aircraft Carrier USS Gerald Ford

Troubleshoot & Evaluate work to be done on field returned units from the navy. Complete paperwork and submit quote on repair cost.

Build and Assemble products on the production floor with the highest standard of excellence.

Install ECO’s after material Review Board evaluates red lined document changes

Support Engineering with the testing of PC boards (ATP) Automated Test Process

Maintain proper paperwork for military Standards right down to certificate of compliance from all outside vendors.

Optikos Corporation Wakefield, Mass.

Senior Engineering Technician

09/01/2003 – 09/15/2009

Responsible for Assembly & Testing multiple product lines of electronic assemblies used in custom optical test benches.

Build custom wiring harness used in motion control system also release documents to enable cables to be built by outside vendor.

Modify & integrate other vendor’s equipment to be used in custom optical equipment.

Write test procedures, work instructions and modify assembly drawings needed by manufacturing.

Review & correct drawings and documents during in-process assembly.

Cambex Corporation Waltham Mass

Engineering/Manufacturing Test Technician

02/99-09/03

Responsible for product testing, assembly, configuring PC 2000 PCI to FIBRE and MC1000 MICRO CHANNEL to FIBRE host bus adapters with Q-Logic based BGA chip set

Participated in design review, debug and product release of new FIBRE QUICK HB2000 consisting of 8 PORT FIBRE CHANNEL HUB.

Performed various tasks: assembly, soldering and systems level testing for STOR 9600 CMOS Mainframe Memory. Debugging boards to component level.

JUPITER Technology Waltham Mass

Engineering/Manufacturing Test Technician

06/96 – 02/99

Responsible for assembly, production testing and systems level testing for the following microprocessor (Motorola 68000) based Frame Relay Access Device units: 9658 H FRAD multi-protocol LAN/WAN modular parallel processing system equipped with up to 7 LAN interfaces 13 V.35 interfaces and 31 RS-232 interfaces all contained in one stand alone unit.

VOYAGER T FRAD which contained one Token Ring interface one Frame Relay Port and 3 Async Ports.

VOYAGER E FRAD which contained one Ethernet interface and one Frame Relay Port and 2 Async Ports. VOYAGER K FRAD which contained one Frame Relay Port and 3 Async ports.

Supported Hardware Engineering staff on ECO implementation and all phases of Emissions Testing and Streamlined and documented uniform unit assembly .

IPC/WHMA-A-620 Requirements and Acceptance for Cable and wire harness Assemblies Certificate

IPC-A-610 Acceptability of Electronic Assemblies

Certificate

Powered Industrial Truck Operator training certificate for forklift trucks

Education/ Certifications

Northeastern University

Associates Degree

Engineering Technology Program

Control Data Institute

Certification

Computer Technology

Contact this candidate