Performed data entry within company system inputting Test data, results, work performed, troubleshooting results, and materials used Responsibilities Troubleshooting fiber optics, electrical circuitry/related to telecom industry, and troubleshoot to component level.

In-depth knowledge of assembly and alignment of optical, mechanical and electrical components into subassemblies such as TOSA (Transmitter of subassemblies), and ROSA (Receiver of subassemblies).

Ability to program Micro Processor and FPGA, shorts probe, dc probe, Electrical Eye and Module Calibration, Pre-Burn In, PCBA Functional, Tuning (I & II), Burn In, Final Test, and Ship Prep.

Using LABVIEW software to test PC board and Optical components such as Sub-board, Main board.

Performing fiber optic splicing, cutting, assembly and testing of cables.

Ability to PCBA Functional Testing, R2 (Radia 2) Calibration, and RADIA 2 screening over temperature (Short Cal, RSOT, Long Cal, and Screen & Adjust Thresholds).

Ability to Information recorded to the navigation, Modules assembly, modules Quality inspection, Passive thermal cycle, Default parameter loading, TEC calibration, Tx Tuning, Rx Tuning, Active Burn-In, Error Screening for the Radia 2, Final Test, Customer Configuration, Final module Quality Inspection, and Ship preparation.

Recognized as a group leader and received IPC - A - 610 training certificate.

Work closely at Department of Research and Development with Engineering to build Proto type product such as 600 Pins, Xenpak, Radia I - XFP (Single, Dual Channel, Tunable), Cim, Radia II

(XFP Tunable), XFP Tuning Cable, SFP+ Tuning Cable, SFP+ Tunable GEN-1, SFP+ Tunable GEN-2, SFP+ FPGA, CFP ODB (100G), CFP Coherent (200G), Wave Master, CFP2 (28NM), CFP2 BiDi, CFP2 ASIC’s, and QSFP+ (400G).

Fujitsu Network Communications, Inc

FIBER OPTIC TECHNICIAN/ENGINEERING TECHNICIAN 1999 - 2000, 2009-2010

Responsibilities Fiber Optics Component Testing

Troubleshooting fiber optics, electrical circuitry/related to telecom industry, and troubleshoot to component level.

Performing fiber optic splicing, cutting, assembly and testing of cables.

Test and troubleshoot Fiber Optic unit and optical component using Lightwave Measurement System Agilent 8164A, Optical Spectrum Analyzer ANDO AQ6317B, Lightwave LDC 3900 Modular Laser Diode Controller, Wavelength Tunable Laser Diode Source and Agilent Multimeter 6183A.

In-depth knowledge of assembly and alignment of optical, mechanical and electrical components into subassemblies.

Prepared testing of components following test instructions in adhering to established standards and procedures.

Conducted Troubleshooting using technical information from the blueprints, schematics, work orders, and technical written information to diagnose.

Performed rework and repairing RF Receivers and other communication equipment in the testing area.

Gathered intelligence reports and data in support of testing needs.

Testing, Debug upgrade of PCBs and Servers, subassemblies and final assemblies.

Used of hand, power meter, Network Analyzer (E8362B), and Measuring tools

Performed data entry within company system inputting Test data, results, work performed, troubleshooting results, and materials used.

Millipore / Mykrolis / Celerity / Unit Corporations / Brooks Instruments

Final Quality Controller Technician 2000-2003, 2008-2009

Responsibilities Final test and inspect gas process unit before packaging and delivery.

Check for out-of-specification voltages, calibration, flows, and electronic response.

Look for assembly defects and electronic errors.

Examine and approve associated documentation and paperwork.

Write pass/fail reports.

Updating and formatting the new software for the new product.

Work closely with Department of Research and Development with Intelliflow departments. Sanmina SCI

FIBER OPTIC TECHNICIAN/ENGINEERING TECHNICIAN 2005 - 2008

Responsibilities Troubleshooting fiber optics, electrical circuitry/related to telecom industry, and troubleshoot to component level.

Performing fiber optic splicing, cutting, assembly and testing of cables.

In-depth knowledge of assembly and alignment of optical, mechanical and electrical components into subassemblies.

Test and troubleshoot EDFA "Eribium Doped Fiber Amplify" using equipment Banc test TM105 module.

Using LABVIEW software to test PC board and Optical component. ITT Technical Institutes

Graduation year 2001 Most Recent

Major area of study Electronic Engineering Technology Collin County Community College

Major area of study Computer Science and Pharmacy

Richland College

Contact this candidate