Mechanical Designer Technology Systems

** ******** **, ***, ** ***** H: 603-***-**** C: 603-***-****

e-mail: **********@*****.***,

linkedin.com/pub/allan-clay/45/76a/8b4/

ALLAN CLAY

Mechanical Designer

Work Experience

5-201*-*-**** Carl ZeissSMT Inc-Contract Peabody, Massachusetts

Nano Technology Systems microscopy and analysis instruments

Mechanical Designer/Drafter using Solidworks 17 with Enterprise PDMWorks

•Worked involved, Crated Assembly and Detail drawings of complex machined parts and formed sheetmetal components. Some of the detail parts like the Chamber were 16 pages long. Some design work was involved. Updated ECRs and created new ECRs on changes to the designs.

10-201*-*-**** Photo Diagnostic Systems-Contract Boxborough Massachusetts

Mechanical Designer/Drafter using Solidsworks 17 with PDMWorks

Worked on an Horse Scanner for use with Veterinary Staff.

•Designed and detailed Panels Doors Cover Vents etc, All Sheetmetal Skins were attached to a 2x2 tub steel Frame Scanner.

5-201*-*-**** Mevion Medical Systems-Contract Littleton, Massachusetts

Proton Therapy for Cancer

Mechanical Designer/Drafter using Solidsworks 15 with PDMWorks

•Designed and detailed Two Plastic Theta and Extension covers. Designed and detail a Service Platform made of 6” channel aluminum for Proton Machine that can be serviced. Platform size was 8’ x 9’ at 30’ above floor. Created all Details, Assembly drawings and BOM’s. All information was put into Omnify system for company wide use.

10-12-2015 Diamond Rolltran-Contract Littleton, Massachusetts

Mechanical Designer/Drafter using Solidsworks 15 with PDMWorks

•Designed and detailed Two Bonding fixtures and Two Plating fixtures, for Roll Ring 32 Channel Assembly. Created all Details, Assembly drawings and BOM’s, GD&T was applied on all drawings.

4-9- 2015 Tyco, TE SUB COM-Contract Newington, New Hampshire

Mechanical Designer/Drafter using AutoCad 13

•Worked on taking manual drawings of machine designs and converting to AutoCad 2D geometry and then making details and assembly drawings with bills of materials. Also making plant layouts of assembly lines, machine layouts and remodeling layouts.

4-201*-*-**** Laar’s Heating Systems-Contract Rochester,NewHampshire

Mechanical Designer/Drafter using Solidworks 14 with Enterprise PDMWorks

•Worked on Mascot and Magnathrm Boilers, Creating Solid models, detail drawings and Assembly drawings. The Company had a lot of the same parts being used on other lines of boilers, so using Configurations for Boms,assembly’s and model components was widely used, (works well).

3-201*-*-**** Analogic Corporation-Contract Peabody, Massachusetts

Mechanical Designer/Drafter using Solidworks 14 with Enterprise PDMWorks

•Designed and detailed a Couch/Table that will be in an MRI machine and a Radiation Treatment Machine.

The tables were 8’ and 10’ long sheetmetal. The design was fastened together using perms and studs. Designed in a complex belt/pulley arrange-

ment and belt tensioner to move the tabletop into the bore of treatment and

imaging machines.

The purpose of the design was to enable patients to remain in one room for both imaging and treatment, rather than moving the patient to several rooms, less stress on patient and reducing treatment time.

11-201*-*-**** FloDesign Wind Turbine-Contract Waltham, Massachusetts

Mechanical Designer/Drafter using Solidworks 12 with Windchill PDM

•Designed Modeled and Detail new Wind Turbine Shroud in the shape of a Jet Engine Shroud that sets around the rotor and blades. Designed Ribs Spares Struts and brackets for the Flap and Mixer Lobe Assembly’s Modified Shroud skins with new designs added to the skins aero shape using lofting and rule features in Solidworks. The work involved was with very complex geometry shapes.

2011 Freudenberg Nok-Contract Northfield, New Hampshire

Mechanical Designer using Solidworks 11 and Unigraphics NX5

•Designed Gripper plates used to pick and place molded components from a mold using Unigraphics NX5.

•Designed a Leak test and Engraving machine to inspect and mark seals used in the automotive industries.

8-200*-*-**** American Science & Engineering-Fulltime Billerica,

Massachusetts

Mechanical Designer II using Solidworks 10 with Smarteam and AutoCAD

Assigned to the Cargo Group Inspection Systems for Trucks and Cars.

Vehicles are X-Ray scanned to detect for explosive devices, drugs and illegal cargo. Responsible for modeling, design, documentation and large assembly management using configurations, display states and envelopes to control large assemblies and achieve better performance. Most of the work I was involved in was with large walk-in sheetmetal enclosures built of sheet metal and tube steel. Also worked with smaller sheetmetal enclosures and brackets for electrical components.

•Assigned to the ECOs implementation group.

•Processed ECOs from simple drawing and bom change to complex redesign change. Responsible for writing ECOs and making changes necessary to complete project.

10-200*-*-**** Cambric Corporation-Fulltime Wakefield, Massachusetts

Mechanical Designer III using Unigraphics NX4 w/Teamcenter and Solidworks

•Responsible for designing using UG NX 3D models from 2D legacy Data on Companies A10 Wing Program for the USAF.

•Created all model Data Sets in Teamcenter as well as all Legacy Revision information.

•Responsible for Electrical/mechanic Machine Device Design and Details using Solidworks for various Commercial and industrial customers.

11-200*-**-**** Goss International-Contract Durham, New Hampshire

Mechanical Designer using UG NX4

•This Company builds large printing presses and folders for the newspaper and magazine industry.

•Designed sheet metal guarding for drive belts, doors and panels. Built large assembly layouts using Shafting, bearings, cams, weldments, sheet metal, etc. Assemblies worked with ranged from 200 to 7000 part assemblies. All modeling was sketch driven in one file with drafting being done in another file.

7-200*-**-**** DePuy Spine-Contract Raynham, Massachusetts

Mechanical Designer using UG NX2

•Worked on the Bobcat Cervical Implant project. Involved in the design of new implants (cage) for cervical area C1 through C7, sizes small, large and Xlarge implants, height range 18mm through 66mm.

•Designed a new Distracter Implant Inserter, Trials and Bone graft instruments to go with Bobcat Implants.

•Responsible for accurate cad models, design, assembly and detail drawings using UG Sketcher with parts families.

2-200*-*-**** Gillette Corporation-Contract S. Boston, Massachusetts

Mechanical Designer using UG NX2

•Designed involved castings sheet metal and plastic parts.

•Designed Carrier/Magazine assembly for automatic handling system used for loading and unloading components to be assembled for a new product line.

•Designs involved design concepts, modeling and drafting of castings, complex plastic layers, sheet metal machined parts and go/no go gages.

4-200*-*-**** DePuy Spine-Contract Raynham, Massachusetts

Mechanical Designer using UG V18

•Designed a Bone Marrow Aspiration Handle made of plastic with stainless steel needle, which extracts bone marrow from the hip area.

•Designed a new generation of concentrator which is a mixer for bone marrow, saline and a blood clotting solution that is formed into a gel which is inserted into the spinal column area to fuse together with bone.

•All designs involved complex plastics components.

5-200*-*-**** Hitchiner Manufacturing-Contract Amherst, New Hampshire

Mechanical Designer/Drafter using UG V18

•Designed wax molds for the aerospace and automotive industries. Wax molds are designed to produce ceramics on ring molds which then creates a metal casting.

•Designed single, double and quadruple cavity molds with manual and pneumatic ejection systems, side action with wedge and cam pins, balanced feeders etc. Work involved shrink prints: building customer models from supplied prints, then proceeding with designing the mold to customer specifications.

3-199*-*-**** Gillette Corporation-Contract S. Boston, Massachusetts

Senior Designer using UG V16 and AutoCad 2000

•Designed complex plastic trays 400 X 600 mm for automatic handling system used for loading and unloading.

•Designed a measure (test) fixture used to calculate dimensional locations.

•Designed a lifting tool used in manufacturing for lifting die components.

•Built a large die assembly which consisted of 700 (plus) parts using UG assemblies.

•Did some freeform modeling for the Excel sensor razor, the MACH3 Razor and contributed in the modeling of the women’s new razor – Venus – which went on the market in 2001.

Additional work history with the following companies – detailed information upon request.

•General Electric Company – Schenectady, New York – Designer using UG V12, Lynn, Massachusetts- Onsite Mentor (for Unigraphics Solutions Support Services

•Johnson & Johnson Orthopedic Company – Raynham, Massachusetts

Senior Tool Designer using Unigraphics.

•UTC Pratt & Whitney Engines – E. Hartford, Connecticut – UGII Mechanical Designer

EDUCATION

Training on Pro e CERO 2.0 4 week course.

Extensive training and professional development coursework at a variety of locations from 1987 to the present including training on Unigraphics and NX, AutoCAD Rel 13 & 14, Computervision CAD-System, machine tool technology, geometric dimensioning and tolerancing, (GD&T), plastic part design, and GE Internal Drafting policies and procedures.

Mechanical Drafting Program, Whittier Technical School, Haverhill, MA – Drafting and Design Certificate.

Welding and Machine Shop I and II certificates. Eight years manual drafting experience.

Contact this candidate