Operations Engineer Process
Resume:
ATEF NAGY
Process/Operations Engineer /DCS Operator
Accomplished Process Engineer with more than 18 years enforcing compliance and improving steps in accomplishing goals. Successful and driven individual committed to proactive planning and goal-oriented with an academic excellence through pre-master's degree in petroleum engineering. Duties and responsibilities extended to conceptual design, plant commissioning, start-up, troubleshooting, operation and process simulation.
Contact
Address
Kafr sheikh -Egypt, A 33727
Phone
************@*****.***
https://www.linkedin.com/in
/atef-nagy-295773163/
Skills
Equipment
specifications
Excellent
Project
Scheduling
Excellent
Process
Development
Excellent
Operations
analysis
Excellent
Process flow
diagram
development
Excellent
Process flow
analysis
Excellent
Work History
2019-01 -
Current
Process/operations Engineer/ DCS Operator
Gulf of Suez petroleum company (GUPCO) Gas
plant, Red sea, Egypt
Prepared mass balance reports for plant products like sales gas, LPG & condensate
Supervised two LPG producing plants using sequence of dehydration units, isentropic expansion in four turbo expander units including commissioning
Supervised charging of molecular sieve change for gas dehydration units
Provided technical assistance to production team when issues arose.
Increased product yield by implementing improved processes.
Conceptual process design &Engineering including performing process simulation, design calculations, process optimization, sizing and selection of
equipment.
Optimized process conditions through review of
product analysis and adjusting operating conditions to ensure safe and continuous operation with
maximum productivity
Developed sizing information for Process Equipment
(compressors, pumps, heat exchangers, distillation columns, separators, etc.) and provide information in form of equipment data.
Improvement
tracking
Good
Workflow
planning
Excellent
Database
administration
Excellent
Documents
and reports
Excellent
Information
modeling
Excellent
Project
coordination
Excellent
Quality
assurance
Excellent
Production
schedules
Excellent
Efficiency
Improvement
Excellent
Software
HYSYS
Excellent
AutoCAD
Excellent
Microsoft
office
Excellent
Languages
Arabic
Excellent
English
Very Good
Developed piping and instrumentation diagram
(PIDs), Heat flow Diagrams (HFDs), and process flow diagrams (PFDs)
Operate the DCS for plant startup and shutdown
operations in order to meet production targets.
Monitor and control all process parameter conditions such as flow rates, pressures temperatures, levels, etc., through displays, graphics and trend logs.
Communicate with field operators for parameter
adjustments in field.
Report to shift supervisors in case of parameter abnormalities and process deviations immediately
Makes minor plant adjustments when necessary and reports any serious faults to the supervisor with
appropriate remedial actions, implement
immediately the approved actions, procedures and
standard emergency responses.
Take immediate corrective actions to limit risk to personnel,plant equipment and production during
emergency situations
Monitor and control the usage of raw materials,
chemicals and other plant utilities effectively to an optimum level in safe manner.
Prepare and assist in preparation of necessary plant – operational reports as requested by production
supervisor or team leader
Ensure the safe shutdown,isolation and blow down of relevant section plant during emergency situations
Identify and investigate the faults and inform the concerned department, for remedial action.
Adhere to company's HSE policy, standard and
approved operating procedures while performing
the duties /tasks.
Perform other related duties as assigned by supervisor such as taking part in training /developing new
recruits/implementing orientation programs.
Preparing necessary reports, plant shutdown and
start up procedures, etc.
Provided equipment& systems failure analysis to
process-engineering experts to establish root cause analysis and select methods of control& protection
Prepared smart pigging projects to full inspect all transmission pipelines including but not limited to planning, coordinating and supervising activities of corrosion coupons retrieving for all equipment's
Monitoring locations.
Created process simulations to test operational
outcomes without causing service disruptions.
Analyzed critical line data to make
recommendations for improvement.
Prepared scope of work documentation for use in
project planning
Interfaced with area teams to verify application of technical details.
Drove cost savings through improved productivity, material utilization improvements and by optimizing labo
Managed 10 employees with continuous coaching
and mentoring.
2016-11 -
2018-12
Projects Engineer
Inspecta International company at gulf of Suez
petroleum company, Ras shuker, EGYPT
Evaluated, inspected and assessed underground
piping wrapping condition (coating conductance
tests, and selecting/suggesting appropriate re-
habitation techniques
Prepare schedule, coordinate and monitor the
assigned engineering projects.
Interact daily with the clients to interpret their needs and requirements and represent them in the field.
Participated in plant inspection for mechanical
completion
Close monitoring for firefighting loop internal corrosion through evaluating water severity (coupons retrieving every three months due to it is critically) and
chemicals injection doses adjusting.
Monitor compliance to applicable codes practices, QA/QC policies, performance standards and
specifications,
Gathered and organized material samples to use in third party testing, evaluated results and reported on findings to optimize materials choices.
Planned and evaluated new projects, consulting with other engineers and corporate executives as
necessary.
Perform overall quality control of the work (budget, schedule, plans, and personnel's performance) and
report regularly on project status.
Successfully maintained clean, valid driver's license and access to reliable transportation.
Supervised work of technologists, technicians and other engineers and scientists.
Understood and adhered to budget, schedule and
quality requirements.
Review engineering deliverables and initiate
appropriate corrective actions.
Education
2017-07 -
2019-07
Pre MASTERS: Petroleum Engineering
Cairo University, Faculty of Engineering - Cairo, Egypt 2011-07 -
2016-07
Bachelor of Science: Petroleum oil and gas Engineering AL Azhar University, Faculty of Petroleum - Egypt
Certifications
2018-10 NON DESTRUCTIVE TEST(PT,MT.VT,UT.RT)
2019-12 ASME B31.8
2020-05 HYSYS process modeling
2021-11 Projects Management Professional(PMP)
2021-02 Distribution control system management
2022-05 Dynamic process simulation using HYSYS
2023-04 Refining and petrochemical diploma
Contact this candidate