Heavy Equipment Control Tech
Resume:
Harold Compton
Sit Hand/Solid Control Tech - Des Dynamic Energy Services LLC
Arlington, TX 76017
***************@*****.***
To secure a position in the Oil Industry that offers challenges as well as opportunities for advancement. Willing to relocate: Anywhere
Authorized to work in the US for any employer
Work Experience
Sit Hand/Solid Control Tech
Des Dynamic Energy Services LLC
November 2016 to Present
•Operating, monitoring and maintenance of solids control equipment for onshore drilling rigs,
•Operating Heavy Equipment Excavator, Etc.
•Dewatering sites, shop areas and other oil & gas related sites.
•Rigging up and down location equipment.
•Working on centrifuges, shakers, dryers and augers.
•Run continuous tests on the solids discharge and the effluent discharge on both units along with comparing information with the Mud Engineer to make sure that the centrifuges are set for optimum performance and the gravity percentage of the mud is within the bore tolerance.
•Attend pre-job safety meeting via Website
Traffic Operation Worker I
Dallas Lite and Barricade
December 2015 to September 2016
•Operates a City vehicle (3/4-, -, or 1-ton vehicle) requiring a standard Driver's License, walk-behind paint sprayers, thermoplastic applicators, line remover and propane heat gun, etc.
•Uses common hand tools to perform maintenance tasks. Lays out and installs pavement markings, including crosswalks, stop bars, lane lines, edge lines, legends, symbols, etc.
•Sets up and removes barricades and Traffic Operations Worker I traffic cones to secure safe work sites. Cleans and maintains hand tools, trucks, etc., using solvents and lubricants. Inspects barricade set up to determine compliance with the Barricade Procedures Manual.
•Detects audible backup warning devices and traffic sounds around moving equipment and in close proximity to moving traffic.
•Works in a variety of weather conditions, and in small, cramped areas. Works in physically demanding area, and incumbents must be physically fit for bending, stretching, lifting, and carrying heavy equipment and materials. Meets scheduling and attendance requirements.
•Maintains appropriate work records, including daily log. Knowledge of: the safety practices and procedures used when working near heavy traffic; basic traffic control procedures using traffic control devices; and pavement marking installation procedures, materials, and equipment.
•Ability to: establish and maintain effective working relationships with coworkers and the general public; and perform moderate to heavy manual labor under temperature extremes for extended periods of time.
Wasserstrom - Forklift Operator
different restaurant
September 2015 to December 2015
• Operated Cherry Picker
• Picking orders for different restaurant
• Stacking pallet for shipping department
• Check in wrap and ship order
• Certified fork lift operator
Assisting in the severing
Operating Heavy Equipment Crane
May 2014 to August 2015
Atlas - solid control Tech close down company 05-2014 to 08-2015
•Operating, monitoring and maintenance of solids control equipment for onshore drilling rigs,
•Operating Heavy Equipment Crane, Excavator, Etc.
•Dewatering sites, shop areas and other oil & gas related sites. •Assisting in the severing, trouble shooting & installation of equipment as required.
•Rigging up and down location equipment.
•Working on centrifuges, shakers, dryers and augers.
•Run continuous tests on the solids discharge and the effluent discharge on both units along with comparing information with the Mud Engineer to make sure that the centrifuges are set for optimum performance and the gravity percentage of the mud is within the bore tolerance.
•Attend pre-job safety meeting on location
Solid Control Consultant
Mud tech Services
July 2013 to May 2014
•Monitor, Maintain and operate solid control equipment for Centrifuges, shaker and dryer.
•Separate the oil base from the water.
•Preventative Maintenance required on equipment
•Operate Heavy equipment Excavator, Trac hoe, Forklift, etc.
•Worked 21/7 Rotation and various job site throughout the United States Solid Control Technician
Newalta Environmental
June 2012 to July 2013
•Certified Solids Control Technician
•Proficient use in Mud Recovery Systems M-15 and Electric Vacuums
•Proficient in Augers, Centrifuge, Diaphragm and Mono Pumps
•Augers, RVD Cuttings and Dryers
•Heavy equipment operator
Contracted Delivery Driver
Sears Distribution
June 2011 to May 2012
•Quality assurance prior to delivery
•Deliver y and set up of purchased goods
•Removal of replaced items upon request
Contractor-Delivery Driver
Corey First Home Delivery
October 2010 to April 2011
•Scanned, wrapped and loaded inventory in preparation for delivery
•Delivery and set up of purchased items
Forklift Operator
Metal USA
February 2000 to March 2005
•Loading and removal of skids of metals
•Sheer cutting and preparation of product
•Prepared inventory for customer pick up •Operation of Raymond forklift and overhead cranes Education
certification in Air Condition and Refrigeration
ATI Career Training Center-Dallas - Dallas-Fort Worth, TX January 2011 to June 2012
Skills
PROBLEM SOLVER, QUALITY CONTROL, Solid Control Tech Certifications/Licenses
Global Certification issued by Global Training Centre, Confined space safety basic, Ground Disturbance Level 1, Hazcom, Introduction to fall protection, OSHA Overview, Gas Testing Certification, H2S and Other Toxic Atmospheres, Industrial Firefighter 1, Newalta US First Aid & CPR Certification, Respiratory Protection, Earthmoving Equipment Certified, PEC SAFEGULF/SAFELAND USA Basic ID#: PEC100286171 exp. 12/2016
January 2027
Additional Information
Skills: Responsible and reliable, Able to lift up to 75 pounds, Quality Control, Safety oriented, Efficient, Excellent Problem Solver, Hard Worker and Dedicated to task at hand.
Contact this candidate