Commercial Electrical Safety Training

CLARENCE TURNER

Home Address: * ******* **** ******, ***** Carolina 29078

H: 706-***-**** C: 706-***-**** *****************@*****.***

Seasoned Electrician with 14 years’ experience providing quality service in industrial and commercial electrical areas.

Certified on:

●Safety Training in Fall Protection

●OSHA 10,

●Scaffold, Hilti firestop systems,

●CPR

●Hazard

●Communication (Safety Data Sheets)

●Fixture installation

●Wiring termination requirements

●Fort Lift

Highlights:

●Deep knowledge of National Standard Electrical Code

Electrical

●Safety in the Workplace (NFPA 70E)

●Industrial electrician

●Commercial and Residential Electric

●Lead man of team

●Led hand and power tool safety workshops for new staff members

●Chosen over 15 other electricians by Foreman Mr. Chris Putman of

Barocco Electric to pull wiring for units due to expert, speed and

proficient quality of work.

L and S Co, 04/2017 until present, Electrician, (Foreman)

Baxley, Ga physical location was Fort Jackson South Carolina

Was in charge of large project that employed many different electricians (18) at the same time. Supervised honoring responsibility for providing direction and leadership for electricians ensuring their safety and project proficiency within specific guidelines which include code standard, time requirements, and budget considerations. Held a rapport with base inspectors and company. Managed team, evaluated employees’ progress, trained new team members, attended meetings and identified conflict and independently reaching resolutions.

Eldeco Electric Co, 10/2016 to 02/2017, Electrician

- Kershaw, SC

Performed electrical services for industrial new based project. Installed wiring start and stop buttons among wiring contactors. Tested electrical systems and completing troubleshooting for malfunctions. Responsible for running and bending conduit. Ensured that systems were grounded and installed outlets, lighting fixtures as well as switches. Terminated motor control centers’. Pulled, strapped and ran cable tray. Completed hooking up and terminating switch gears.

Tex-Cap Electric, 10/2014 to 12/2015, Electrician

Austin, Texas

Performed electrical utility services for industrial based and new

building projects. Installed safety systems, including emergency

lighting, uninterruptible power systems and battery systems. Tested

the entire electrical assembly for performance levels and safety

concerns. Troubleshot EMCS and variable frequency drive systems.

Examined and created solutions for high voltage electrical system

issues. Consistently worked to code on all projects, utilizing drawings

and manuals. Traced and diagnosed malfunctions with hand tools and

test equipment such as multi-meters. Connected wires to circuit

breakers and transformers. Connected wires to circuit breakers and

transformers. Directed electricians on installation, maintenance and

repair on electrical wiring and equipment. Ran (bending) conduit,

setting cable trays and grounding, pulling wire and mounting boxes in

charge of a crew 4.

H R Allen Electric, 04/2014 to 06/2015, Electrician

Columbia, SC

Tested and operated a variety of electrical components and systems.

Consistently worked to code on all projects, utilizing drawings and

manuals. Traced and diagnosed malfunctions with hand tools and test

equipment such as multi-meters. Connected wires to circuit breakers.

Running conduit, setting boxes and pulling feeds for rooftop units and

terminating the units also using table benders wiring switch packs.

Directed electricians on installation, maintenance and repair on

electrical wiring and equipment. Read blueprints and put in custom

lights. Troubleshot EMCS and variable frequency drive systems.

Installed safety systems, including emergency lighting, uninterruptible

power systems and battery systems.

Auburn Electric, 10/2012 to 06/2013, Electrician

Phoenix City, AL

Read blue prints, setting transformers and pulling feeds for switch

gears and terminating them. Pulling branch circuits low and high

voltage for lighting and power and a troubleshooter. Directed

electricians on installation, maintenance and repair on electrical

wiring and equipment. Traced and diagnosed malfunctions with hand

tools and test equipment such as multi-meters. Tested the entire

electrical assembly for performance levels and safety concerns.

Faith Technologies 08/2010 to 10/2011 Electrician

Kennasaw, GA

Lead man read blueprints. Set man holes running communication duct banks and also used sniffer to ensure no hazardous gases were present.

Completed layouts for underground. Set panels and pulled main

feeds. Ran conduit and pulled circuits. Tested the entire electrical

assembly for performance levels and safety concerns. Traced and

diagnosed malfunctions with hand tools and test equipment such as

multi-meters. Worked extensively on three-phase, 277/480-volt power

distribution systems. Connected wires to circuit breakers and

transformers. Directed electricians on installation, maintenance and

repair on electrical wiring and equipment.

Southern Electric Services, 02/2008 to 07/2010, Electrician

Nashville, TN

Read blueprints. Completed underground lay-out for communication

room and electrical rooms. Kept pace with block masons ensuring job

was not behind. Set panel and wiring MDP. Ran conduit. Set boxes,

racks, wire cable for trays and bonding. Put up bus ducts. Troubleshot

EMCS and variable frequency drive systems. Tested and operated a

variety of electrical components and systems. Traced and diagnosed

malfunctions with hand tools and test equipment such as multi-meters.

Connected wires to circuit breakers and transformers. Directed

electricians on installation, maintenance and repair on electrical

wiring and equipment.

Mosses Electric, 10/2005 to 01/2007, Electrician

Pensacola, FL

Lead man directed electricians on installation, maintenance and repair on

electrical wiring and equipment. Consistently worked to code on all

projects, utilizing drawings and manuals. Connected wires to circuit

breakers and transformers. Installed safety systems, including

emergency lighting, uninterruptible power systems and battery

systems. Tested the entire electrical assembly for performance levels

and safety concerns. Directed electricians on installation,

maintenance and repair on electrical wiring and equipment.

Barocco Electric, 06/2004 to 10/2005, Electrician

Pensacola, FL

Consistently worked to code on all projects, utilizing drawings and

manuals. Ran pvc for lay-out. Ran the communication and electrical

room. Set transformers hooking up main distribution panel and pulling

feed. Traced and diagnosed malfunctions with hand tools and test

equipment such as multi-meters. Tested and operated a variety of

electrical components and systems. Directed electricians on

installation, maintenance and repair on electrical wiring and

equipment.

Contact this candidate