Project Engineer
Resume:
CURRICULUM VITAE
SWATHI B.M. Email: ********@*****.*** M.Tech in VLSI & Embedded Systems Contact: 974-***-****, 998*******
Career Objective:
To work as a VLSI Verification/Design Engineer in an esteemed organization where I can utilize & enrich my knowledge and skills while contributing my best to the development of the firm with dedication and persistence.
Educational Qualification:
Qualification
Board
Institution Name
Year
Percentage
Master of Technology (VLSI Design & Embedded System)
VTU Belgaum.
BNMIT, Bangalore
2015
73.95%
Bachelor of Engineering (Electronics and Communication)
VTU Belgaum.
JNNCE, Shimoga.
2012
60.23%
DIPLOMA
(Electronics and Communication)
Board Of Technical Education, Bangalore.
Adichunchanagiri Polytechnic, Chikkamagalur.
2009
65.20%
S.S.L.C
Karnataka Board of Secondary Education
Loyola High School, Shimoga.
2006
75.68%
Technical Skills:
Operating System
Windows 98/XP/2000/7/MS-DOS.
Programming Languages
C, C++, VHDL, Verilog, SV, UVM, ALP.
Area of Interest
VLSI Design & Testing.
Simulation Tools
Questa Sim, Cadence, Xilinx.
Work Experience:
Working as an Engineer at ADE (Flight Control Computer Division), Bangalore. From 02/11/16 to till date.
Worked as Project Intern in ISRO (Controls and Digital Electronics Group), Bangalore. From 01/08/14 to 29/05/15.
Project Details:
Design & Implementation of TRRT FPGA for SAT-4
SAT-4 is an advanced communication satellite with multi spot beam antenna. An on-board RF tracking system is required to accurately point the on-board antenna to ground. The on-board RF Tracking system consists of Tracking Receiver Remote Terminal (TRRT) Interface unit which collects error and control signals from Receiver/Transmitter control unit. This TRRT interface unit consisting of FPGA card collects the data from PROM, also the error and control signals from Receiver/Transmitter control unit which are stored in SRAM. The summit device collects the stored data from SRAM and processes the signals and corrects it. These corrected signals are given to altitude orbit control system to drive the antenna in the required direction.
A Project on Voltage Controlled Oscillator (M Tech Project)
A Voltage-Controlled Oscillator or VCO is an electronic oscillator whose oscillation frequency is controlled by a voltage input. The applied input voltage determines the instantaneous oscillation frequency. Consequently, modulating signals applied to control input may cause frequency modulation (FM) or phase modulation (PM). A VCO may also be part of a phase-locked loop.The proposed VCO circuit is made up of ring oscillator using delay cells. The operating frequency is determined by the number of delay cells in the ring oscillator. This project is carried out using Cadence 180nm technology.
A Project on Asset Security using 1 mm distance accuracy with GSM (B.E. Project)
The purpose of this project was to design a system for securing the Asset using 1mm distance accuracy with GSM .This project not only provides the security also gives the distance moved by the asset. The LPC2103 ARM Controller is the heart of the project. The asset can be secured using PIR sensor which detects the presence of human in the RF area and IR Sensors detects human in 5cm, the sensed signal transfers to the ARM Controller which controls whole operations of the model, the detected human and distance moved by the asset will displayed on the LCD, same time the message will sent through GSM which controls the operations of the whole module.
Personal Details:
Date of Birth : 27/02/1990 Sex : Female
Marital Status : Unmarried
Linguistic Skills : Kannada, English, and Tamil.
Present Address : C/o Shyla Ramesh, No.46 (old), 114, 9th cross, Lakshmipuram, Ulsoor, Bangalore.
Permanent Address : D/o Balakrishna.D. Assistant Master, D-169 “Harsha Nilaya” D-block,
Gopalgowda Extension, Shimoga-577201. Karnataka.
Declaration:
I hereby declare that, all the details given above are true to the best of my knowledge and belief.
Thanking you, Yours faithfully, Place: Date: (Swathi B.M.)
Contact this candidate