Engineering Electrical

VAMSHI THATIPALLY

***** ****** ***** ***. ***, Southfield, MI – 48034. *********@***.*** 248-***-**** EDUCATION

Lawrence Technological University Southfield, Michigan December 2017 (Expected) Master's Degree in Electrical and Computer Engineering GPA: 3.10 Jawaharlal Nehru Technological University Hyderabad, INDIA September 2011 - May 2015 Bachelor's Degree in Electronics and Communications Engineering GPA: 3.10 SKILLS & ABILITIES

MATLAB Keil μVision OCTAVE DFMEA

C/C++ ECAD/AUTOCAD PROTEUS PSpice

Embedded C LabVIEW Circuit Lab MS Office

Experience with serial communication protocol UART, I2C, SPI, RTOS, Linux based virtual box and Communication protocols UDP, Cellular networks (3G, 4G, LTE, and 5G). Bill of materials (BOM).

Knowledge in AUTOSAR, ISO 26262, LIN, CAN (ISO 11898), electronics (Digital and Analog), ARM processor, PIC controllers, PCB Layout Interfacing Hardware and Embedded software and Debugging, Verification of FPGA using Active – HDL. WORK EXPERIENCE

Electrical Team Member, Formula Hybrid May 2016 – December 2016 Lawrence Technological University

Learned the development of High Voltage circuit (Vehicle Electrical Architecture).

Developed Pre-charge and Discharge circuits ensuring the safety of the vehicle.

Improved skills in the development of Wiring Harness and Fusing for the vehicle.

Acquired knowledge and experience on Data Acquisition of Motor Controller, Battery Management System, Wheel speed sensors, Transmission, Engine control unit using CAN. RF Test Intern, Silicon Tech Labs, India July 2015 – October 2015

Worked on the characterization of the RF Chip - RS9113.

Tested the performance of the Receiver for SNR, EVM, and Rx IQ Imbalance using Function generator.

Evaluated the performance of the Transmitter for Power measurement of Tx Packet, EVM, Spectral Mask, Tx Emissions and Crystal Tuning characteristics using Oscilloscope. PROJECTS

Automatic Car Parking System - Embedded Systems February 2015- May 2015

Automatic Parking System was designed using PIC18F452 microcontroller, power supplies, RFID, IR sensor, LED‘s, LCD, DC motor, limit switches and a buzzer.

Express PCB, PIC C compiler and Proteus 7 were used for designing the circuits, compilation and for simulation. PicC kit 2 for burning code into Microcontroller. Interfacing sensors and DC motor to microcontroller with RS-232. Hand Gesture Based Home Automation - Embedded Systems March 2014- May 2014

AT89S52 Microcontroller, Relay, LCD, RF transmitter and receiver, MEMS accelerometer, DC 0808 are main components used for design.

Keil micro vision is used for compiling and simulating, Atmel Flash ISP software and Programmer kit for dumping the code into Microcontroller.

Wireless Data Transfer Using Light Fidelity (Li-Fi) – Digital Communications March 2016 – May 2016

To resolve the issues of scalability, availability and security, we came up with an idea of creating a prototype to transfer the data using visible light communication (VLC).

MATLAB is used for the image processing, Visual basic interface and RS-232 is used for serial transmission.

At mega 89c51 microcontroller, LED, Photo transistor are the other components used. Vehicular Communication systems – V2V, V2I, V2X January 2017- May 2017

Evaluation of IEEE 802.11p DSRC layers for V2V and V2I communications.

Analysis of vehicular collision warning and collision avoidance communication protocols.

A survey on Wireless ad hoc and sensor networks. CERTIFICATION

National Scientific Research Center HYDERABAD, INDIA August 2015 – November 2015 Advanced Diploma in Embedded Systems

LEADERSHIP & VOLUNTEERING

Secretary for IEEE Student Chapter at Lawrence Technological University. May 2016 - Present Coordinator for Technical Fests at Mallareddy college of Engineering.

Contact this candidate