Engineer Design

Saravanan Mysore

***** ***** **** **** ****: 704-***-****

Farmington Hills, MI 48335 Email: **********@*****.***

Visa Status : US Permanent Resident/Green Card Holder

Technical Skills

Hardware Microcontrollers: Hitachi H8, Mitsubishi M16c

Motorola 68HC11, MPC5534, Microchip,ST,

MSP430, Infineon Aurix.

DSP: TMS 320F280x, TMS320F28x, PICOLO

Programmable Logic FPGA (Xilinx, Altera)

Debugging Tools Digital Oscilloscopes, In-circuit Emulators, Logic

Analyzers, and Spectrum Analyzers.

Languages C, C++, Assembly, Visual Basic, Labview

Operating System Windows, Unix, Linux, VxWorks Real-Time

Embedded Operating System

Others Matlab/Simulink, Mathcad, Orcad, Pcad, Mentor, Allegro,Pspice, LTspice,SI Metrix, VHDL, PFMEA,

DFMEA, Microsoft Project, DVP&R, PPAP/PSW

Work Experience

Hitachi Automotive Systems, Farmington Hills, MI (08/22/16 – 11/21/16)

Senior Engineer

Development of transmission control module for automotive applications.

Participated in developing worst case analysis, test procedures, DFMEA and led cross functional team members.

Franklin Electric, Fort Wayne, IN (06/15/15 – 09/10/15)

Senior Engineer

• Development of field oriented control based motor drives for pump applications.

IBM/Lenovo, Raleigh, NC (05/20/13 – 06/10/15)

Power Engineer

Development of switch mode power supply circuits using buck, buck-boost, fly-back and half bridge converter topologies including magnetics for server applications.

Development of dc-dc synchronous regulators for CPU and Memory based applications.

Design of AC/DC converters with power factor correction (PFC).

Lead cross functional team members and provide support to manufacturing.

Parker Haniffin, Charlotte, NC (06/18/12 – 02/22/13)

R&D Engineer

Development of DC-DC converters and power supply circuits including magnetics for motor controllers.

Design of DC-AC inverters for induction and brushless DC (BLDC) motors.

Involved in testing dc-dc converters and motor controllers for compliance to standards UL, CSA, IEC/CE.

Leading cross functional team members and providing supports to manufacturing and product quality team members.

John Deere Company, Fargo, ND (10/13/08 – 06/01/12)

Senior Design Engineer

Design and development of high power bi-directional DC-DC converters for electric Combines, Tractor and battery charger applications.

Design and Development of DC-AC inverters using MOSFET/IGBT for driving PM brushless and induction drives for off-highway construction vehicles.

Design and Development of power supplies using buck, boost, buck-boost, fly-back, forward, half bridge and full bridge based topologies for control board applications.

Design of magnetics in power converters/supplies and motors.

Performed simulation including worst case and risk analysis using PSPICE/LTSPICE and Mathcad.

Developed control algorithms and firmware for motor control and power converters using matlab/Simulink and C, C++ for TI DSP and microcontrollers.

Involved in design review, schematic diagram, engineering documentation preparation (ECO, DVP&R, DFMEA, PFMEA, PPAP) and verified PCB layout.

Participated in new product development projects, providing novel ideas and lead cross functional team members.

Interfaced with customers on technical aspects providing solutions for concerns evolved with proper documentation and feedback in timely manner.

Participated in comply regulatory requirements UL, IEC for motor control and analyzed results to make sure the requirements are achieved.

Prepare, Maintain and meet overall program schedule.

Followed Metrics regard to on time project delivery, budget, productivity and quality for the products.

Reviewed and created product requirements and specifications for power supplies, for motor control and power electronics.

Involved in mentoring group of engineers.

Pentair Inc, Delevan, WI (03/24/08 – 10/03/08)

Electrical Product Engineer

Development of inverters for single and three phase motors for pump control applications with UL, CSA regulatory requirements.

Involved in sustaining work on existing products and continuous improvement process for cost reduction purposes.

Interfaced with customers on products and provided feedback on concerns in timely and professional manner.

Tyco Electronics, Winston-Salem, NC (08/06/07 – 02/06/08)

Senior Development Engineer

Development of solid-state relays for fuel door/pump, rear defroster automotive applications.

Software development for microcontrollers using C and assembly.

Provided support to customers on the products application requirements.

Kinetek Controls Cleveland, Ohio, (09/20/02 – 07/31/07)

Electrical Design Engineer

Design and Development of MOSFET/IGBT based motor controllers for Brushed DC, Brushless DC, Induction, PMSM motor drives for low and medium voltage drives and electric vehicle products.

Design of DC-AC inverters for induction and permanent magnet motor drives.

Design of electric motors for Brushed DC, Induction and Brushless DC.

Develop embedded firmware and software for DSPs and microcontrollers for motor control using C, C++ and assembly language.

Develop Simulink models based field-oriented motor control algorithms.

Design and Development of DC-DC converters and power supplies using buck, boost, buck-boost and fly-back based topologies for control board applications.

Design and development of AC-DC converters with PFC control for battery chargers and front end applications.

Modeling, Simulation and Analysis of DC-AC inverters and DC-DC converters using PSPICE, Matlab/Simulink validating models against hardware.

Develop schematic diagram, bill of materials, AutoCAD drawing, ECR, ECN and verify PCB layout.

Develop documentation for controllers including system vehicle diagram, circuit layouts, assembly procedures, and manufacturing specifications.

Develop test procedures for products to ensure functional and design test.

Interfaced with customers to help support for evolving technical issues and providing solutions and feedback in timely manner.

Led a team of design engineers on the development of power electronics and evaluated the products.

Participated in sustain engineering activities, evaluating alternative design solutions meeting product requirements factoring in performance and cost.

Participated in new product introduction (NPI), and led cross functional team.

Created system specifications and reviewed product requirements document and test plans based on customer requirements, prototype build and final design.

Prepare, maintain and meet overall program schedule.

Identify resources, preparing budgets and define schedule to achieve program objectives.

Followed metrics with regard to budget, on time project delivery, product cost and quality for new products as well as support of existing products within plan.

Euro Controls (S) Pte. Ltd., Singapore. (02/20/96 – 12/15/99)

Senior Development Engineer

Developed a 3-phase inverter based motor control for HVAC applications.

Develop design guides, application notes for various motor drives.

Worked with customers from first contact through opportunity assessment, concept development, quotation, project team management, detailed design and verification.

Worked with marketing and product managers with customer requirements to develop new products and improvements on existing products.

Wood Group Industrial Controls, Aberdeen, UK. (04/08/93 – 11/15/95)

Development Engineer

Developed and implemented PWM and control algorithms for 3-phase PWM inverters for induction motors and UPS applications.

Provided support for the design of front end 3-phase AC/DC rectifiers for UPS applications.

Worked with customers to create solutions for their specific product issues.

Designed and implemented line current, vibration and end-winding leakage flux monitoring for detection of broken rotor faults in induction motors.

Education University of Akron, Ohio, USA.

Aug’00 – Dec’01 M.S. in Electrical Engineering (Incomplete)

Apr’91 – Nov’95 The Robert Gordon University, UK.

Master of Philosophy (M.Phil) by Research & Thesis.

Area of Study: Power Electronics and Motor Drives

Aug’83 – May’88 Madurai Kamaraj University, India.

Bachelor of Engineering (Electrical and Electronics)

References Furnished upon request.

Contact this candidate