Technician Electrical

STEVEN F. COCANOUR

**** ******** **. 614-***-****

WEST JEFFERSON, OH 43162 *********@*******.***

SUMMARY

Experienced in electronic troubleshooting, calibration, testing, and repair of a variety of electronic products including automotive validation, structural and static testing, and aircraft lighting system testing. Trained in performing a wide range of validation testing on various circuit boards and engine dyno testing.

PROFESSIONAL EXPERIENCE

AVL Powertrain Engineering, Inc. (Honda R&D) 2016 to present

ENGINE DYNAMOMETER PERFORMANCE & DURABILITY TECHNICIAN

Operation of highly sensitive, complex analytical test equipment and control software for Chassis Dyno, Emission Analytical systems, and supporting test equipment.

Monitor testing and verify test integrity

Setup engines

Setup instrumentation (thermocouples, pressure transducers, blow-by meter, coolant and oil conditioners, Etc.

Build & teardown engines

Use proper torque & procedures

Record/document break away torques

Columbus Castings 2015 to 2016

TEST TECHNICIAN

Perform testing on castings for maximum combined operating load limits and testing to destruction to establish actual margins of safety, static load limits, fatigue performance, and anticipated casting life.

MTS High Force Load Frame System: Fatigue and Static Test machine with 1.1 M pound and two 350,000 pound servo-hydraulic actuators

MTS Portal Load Frames Test Machine: Sixteen servo-hydraulic actuators ranging from 11,000 to 110,000 pound capacity

Application of strain gauge

Use of data acquisition systems

Honda R&D 2015 to 2015

AUTOMOTIVE ELECTRICAL VALIDATION TECHNICIAN (CONTRACTOR)

Perform electrical lab validation testing as requested by development engineers. Fabricate test harnesses and electrical circuits as required. Work with engineers to complete test accurately and on schedule. Troubleshoot vehicles as needed and requested in order to facilitate testing. Assemble and disassemble vehicles in-order to facilitate electrical testing. Fabrication of electrical harnesses, circuits, plastic parts, etc. in-order to facilitate electrical testing.

Static and dynamic DYNO testing

Electromagnetic Susceptibility testing, Ignition testing, Narrowband and Broadband Noise testing

ESD testing

B CAN bus testing

Completed Mid-Ohio School Acura High Performance Program

Honeywell 2014 to 2015

LEAD ENGINEERING TECHNICIAN (CONTRACTOR)

Assist with the development and qualification testing of aircraft lighting systems that satisfy customer, FFA, and internal requirements. Set up and perform Temperature Variation, Overpressure, Altitude, Salt Spray, and Solar testing.

Support the development, qualification, and certification of specific tests as defined in DO-160 and other relevant customer test requirements documents

Tear down assemblies to look for wear, damage and other non-compliance to the drawing set

Troubleshoot test set-ups and configurations and propose solutions

Provide technical support to the project and systems engineering test teams

Abbott Nutrition, Columbus, Ohio 2009 to 2013

REPAIR TECHNICIAN

Evaluated, performed troubleshooting, labeled, and upgraded internal delivery systems to assure that the medical device met performance and label claims.

Repaired a variety of pumps above the standard rate of 2.25 per hour while staying below the standard rejection rate of less than two percent

Documented all repair information accurately using an electronic device history record computer system

Cross-trained on multiple pumps to enable the company to meet customer needs

Adhered to stringent SOP’s (standard operating procedures)

Invensys Climate Controls 1999 to 2008

ELECTRONICS TEST TECHNICIAN

Set up and performed Design, Annual, and UL validation tests including but not limited to: Full Functional, Power Supply Interruption, Ramp Voltage, Transient Over-voltage, Electrostatic Discharge, Heat Rise, Electrical Life Water and Gas Valve.

Performed validation testing witnessed by UL and CSA agencies

Furnished written lab reports analyzing data for internal and external use

EDUCATION

Miami Valley Career Technical Center

Electrician Certificate, 1996

Central Ohio Technical Center

Associates Degree - Mechanical Engineering Technology, 1982

Professional Development

Electro-Mechanical, DC Electronics, and AC Electronics

Certified Microscopic Soldering and Assembly

TQM, Total Quality Management (SPC, Team Management, Quality Circles and More)

OSHA/RCRA Hazardous Facility Training

CPR, First Aid, and the AED (Automated Electronic Defibrillator)

Productivity Point training seminars in Word and Excel XX

Contact this candidate