***** *. ******** *****

HOCKLEY, TX *****

JOHN J. ADAMO acwr8i@r.postjobfree.com Cell 281-***-****

SUMMARY

I am a Quality professional with over thirty years’ experience in the manufacturing, test, repair, and inspection of electronic and electro-mechanical assemblies for military, aerospace, and commercial industries. During my career, positions of responsibilities have been Quality Manager, Sr. Quality Engineer, Supplier Quality Auditor, Internal ISO Lead Auditor, Corrective Action Engineer, Technical Support, Quality Planner, and Inspector.

EXPERIENCE

Ducommun LaBarge/STC, Inc. (Contract Electronic Manufacturing Service) 2010 - 2015

Stafford, Texas

Sr. Quality Engineer (Process Engineer, Customer Focus Engineer)

Developed, implemented and maintained certification for ANSI/ESD S20.20 program.

Reduced scrap to site record low of 0.48% of sales by implementing changes to process and procedures.

Created manufacturing Work Instructions from customer drawings and specifications.

Reduced Customer returns by performing final inspections and training QC and operators to Customer requirements.

TS3 (ALPHA CIRCUITS) (Contract Electronic Manufacturing Service) 2006 - 2009

Stafford, Texas

Quality Assurance Manager directly responsible for the Quality Management System, 23 Quality Inspectors, Document Control, Training, ISO 9001:2000 and TL9000 audits, Quality Engineering, and UL Audits.

Quality Engineer responsible for process improvement, weekly and monthly metrics, and root cause analysis. Support Supplier Quality Audits, Internal ISO Audits, Material Review Board, and the Corrective & Preventive Action process.

BENCHMARK ELECTRONICS INC. (Contract Electronic Manufacturing Service) 2004 - 2006

Angleton, Texas

Quality Engineer responsible for the evaluation and improvements of process and product during the manufacturing of Telecommunication equipment through SMT, wave solder, assembly, and test. Developed and implemented a component traceability system to PCBA level for Customer.

STEWART & STEVENSON, Engineered Products Division 2001 - 2004

Houston, Texas

Lead Quality Inspector for the manufacturing of Well Servicing Equipment, Standby Generators, Rail Car Movers, and Snow Blowers.

Developed Microsoft Access Databases for the tracking and analyzing of receiving inspection, in-process nonconformance’s, serialization of top and sub components, Corrective Action’s, Customer Complaints, Service and Warranty

Headed the implementation of a paperless system for procedures, work instructions and standards.

RADISYS CORPORATION 1999 - 2001

Houston, Texas

Quality Analyst/ ISO Lead Auditor

Manufacturing Representative for the ISO Quality Management System in the design and manufacturing of computers and related products

Collected, analyzed, and reported weekly, monthly and quarterly reports for systems and PCBA yields, DPMO, average outgoing quality, OTD, DOA and early warranty reports to corporate

JOHN J. ADAMO PAGE 2

STEWART & STEVENSON, TVS DIVISION 1998 - 1999

Sealy, Texas

Supplier Quality Assurance Auditor

Responsible in performing a systematic and independent survey evaluations, and supplier and internal audits to verify Quality Systems are implemented and in compliance with applicable specifications and requirements : MIL-I 45208, MIL-STD-45662, FAR 52.246-2 or compliance audit to ISO 9001

SYNTRON, Inc. (Sercel) 1994 - 1998

Houston, Texas

Quality Process Engineer / Process Auditor

Responsibilities include statistical process analysis, conducting audits internally and externally, ESD coordinator and trainer, auditing and maintaining the calibration system.

Performed electrical testing and evaluation during the development and qualifications of reduced diameter transmission cables and ocean bottom cables

VARI-L COMPANY, INC. 1992 - 1993

Denver, Colorado

Quality Inspector responsible for the inspection, test, and acceptance of thin film and discrete components and assemblies to Mil-Std-883 and Mil-Std-202 at incoming receiving, in-process, and final.

Martin Marietta Astronautics Group (Lockheed Martin) 1980 - 1991

Denver, Colorado

During my 11 years with Martin Marietta, I held the positions of Hardware Acceptance Engineer (Senior Quality Engineer), Corrective Action Engineer, Quality Technical Support, Quality Planner and Quality Inspector. During this time, I participated on projects such as Space Shuttle, Manned Maneuvering Unit, Titan Launch Vehicle, Galileo, Peace Keeper, MX Transport Emplacer, and Defense Systems. Some accomplishments while on these projects were:

Reduced the risk of system level test failures and mission failures by the identification of hardware and test anomalies found during data reviews of electronic and electro-mechanical assemblies

Created summaries of all mission critical hardware and presented accurate status of flight hardware to Customers, Consultants, Management, and Engineers at incremental summary reviews

Received three Employee Commendations for outstanding work performance

SOFTWARE APPLICATIONS

Knowledgeable in the use of Microsoft applications: Word, Excel, Access, Project, Power Point, Outlook.

Worked with several MRP systems; MRPII, JD Edwards, SAP, Syteline, BANN.

Other interface programs used were Agile, Power View, Process Feedback System (company developed).

EDUCATION & TRAINING

Team Building - Coaching - Mentoring Seminar (National Seminars) 2007

Management Skills (Rockhurst University Continuing Education) 2007

Advance Microsoft Access 2000

University of Phoenix, Aurora, CO 1992

Total Quality Management, Accredited Certificate Program

ISO 9000 Internal Auditor Training (ABS) 1998

Certified Quality Engineer Refresher Course, ASQ 1996

Computer Classes: 1995 - 1996

Advance Microsoft Word, Advance Microsoft Excel, Microsoft Project

Red Rocks Community College, Golden CO 1985

Associate in Applied Science

Major: Electronic Digital Technology

Contact this candidate