Mechanical Engineering Engineer
Resume:
Objective:
To obtain a full time position in the field of Automotive Engineering
Educational Background:
Michigan Technological University Houghton, MI
MS Mechanical Engineering (GPA : 3.11) Jan. 2015- Apr. 2016 University Of Pune Pune, India
BE Mechanical Engineering Aug. 2010-July 2014
Certification:
Hybrid Electric Drive Vehicle Engineering Graduate Certificate Advanced knowledge and hands on experience in design, analysis, control, calibration and operations of HEVs Engineering Experience:
MTU Hybrid Electric Vehicle Enterprise Houghton, MI Mechanical Engineer Jan. 2016-Apr. 2016
Developed a powertrain model using AMESim for a 1950 Chevrolet truck equipped with hybrid powertrain
Simulated it to get power, torque, engine efficiency, power losses, fuel consumption on UDDS drive cycle Areion Motorsports Pune, India
Mechanical Engineer Sept. 2013-Sept. 2014
Designed and manufactured vehicle chassis of a formula type racecar using Catia V5
Designed push rod suspension geometry, steering mechanism, gear shifting mechanism, differential mounting, hub and knuckle assembly, fuel tank and vehicle flooring
Participated in the 2014 Formula SAE, Italy. Achieved 35th rank in overall classification Project Experience:
Development and Optimization of a 2010 Chevrolet Malibu Model Jan. 2016-Apr. 2016
Developed HEV model to baseline parameters of 2010 Chevrolet Malibu using MATLAB/Simulink/Stateflow
Measured fuel economy, performance parameters and analyzed cost by implementing technologies viz. torque blending, regenerative braking, E-motor assist, start-stop, engine downsizing, mass reduction
Performed sensitivity analysis to select best combinations which meet current fuel economy standards Study of a Four Cylinder Turbocharged Diesel Engine Sept. 2015-Dec. 2015
Studied the tests done on a FIAT 1.3 multi-jet diesel engine. Modeled the system on GT-Power
Simulated for engine power, torque, brake specific fuel consumption, indicated mean effective pressure and rate of heat release. Compared and validated the results of GT-Power with reference material Analysis of Emissions and Air to Fuel Ratio for Cummins ISL & ISM Heavy Duty Engines Sept. 2015
Studied PM filtration and oxidation characteristics in a Catalyzed Particulate Filter (CPF) from test data
Calculated AFR, combustion efficiency, brake specific fuel consumption and emission index based on measured emissions for five test points during passive oxidation for DOC upstream measurement
Determined AFR for 3 locations UDOC,DDOC, DCPF to check the presence of leakage Emission Analysis using Horiba Gas Analyzer on Powertrain Dynamometer Apr. 2016
Measured emissions of a 0.6L Gasoline Direct Injection engine for rich, lean and stoichiometric mixtures
Calculated the AFR and λ values and evaluated the effect of span error on sensitivity of AFR and λ Modeling of a Hybrid Electric Vehicle Sept. 2015-Dec. 2015
Developed a HEV model with varying torque blending of IC engine and permanent magnet DC motor
Simulated the gear switching based on fuel consumption at specific gear using Simulink Study of Impact of In-Cabin Sound in Hybrid Electric Vehicle on Driver Drowsiness Jan. 2015-Apr.2015
Studied the in-cabin sounds in hybrid electric vehicles
Performed tests on 10 samples using the NADS MiniSim simulator
Recorded effects on acceleration, speed, vehicle heading distance, steer angle, braking Leadership:
Founding PRESIDENT of “Mechanical Engineering Students Association” Jan. 2012-May 2013 EDITOR of "The Mecha Chronicle" Jan. 2012-Dec. 2012 Computer/Technical Skills:
AutoCAD MATLAB Simulink AMESim GT-Power
Dyno Testing C Programming EES Validation Calibration Data Acquisition OBD Vehicle Testing Simulation Emission Analysis CarSim veDYNA NX Pro-Engineer Catia
Other Activities/Hobbies:
Motorsports and car enthusiast, kart racing, amateur photographer, soccer, worked as a Calibration Technician 31331 C Mound Rd Utkarsh Achara
Warren, MI 48092
*******@***.***
Contact this candidate