Engineer Electrical

Anatoli Polotov

Electrical & Instrumentation Controls Engineer

Electronics and Electrical Engineer Electrical Design Engineer

Cell: 704-***-**** Email: *******.**@*****.***

SUMMARY:

Electronics & Electrical Engineer with master's degree in electronic systems and instrumentations with twenty years of experience in design, installation, integration, calibration and maintenance industrial instrumentation and process control equipment such as magnetic and inductive proximity sensors and switches, photoelectric sensors, pressure and temperature transmitters and indicators, signal conditioners, process controllers and digital panel meters, motor controls, functional relays, counters, tachometers, field I/O, PLC (programmable controllers) and HMI (Human Machine Interface).

EDUCATION:

National Aerospace University “KHARKOV AVIATION INSTITUTE”, Ukraine

09/1992 – 02/1998

Master's degree in electronics systems and instrumentations. Qualification: Electronics & Electrical Engineer

TECHNICAL SKILLS:

Design, installation, integration multifunctional relay control systems, temperature and level process control systems, vibration monitoring machinery protection systems for commercial, industrial, and domestic purposes

Design schematic diagrams and PCB design analog signal conditioners, analog and digital I/O interface modules for PLC

Expert in electrical instrumentation system hardware design, schematic and specifications document preparation associated with measurement process control systems based on transmitters, signal conditioners, functional relays, motor controls, analog and digital I/O PLC

Experience with test, installation and calibration electronic, electromechanical, pressure, temperature equipment, wired and wireless electrical meters, field instruments, sensors, laboratory instruments, computerized test systems by using calibration software, following calibration procedures and manuals

Skilled in capacitive and inductive proximity sensors and switches, photoelectric sensors, temperature transmitters and indicators, vibration transmitters, analog signal conditioners, process controllers and digital panel meters, functional relays, counters, tachometers analog and digital I/O PLC

Additional experience in developing and updating ladder diagrams for PLC, updating I/O configurations, hardware troubleshooting

Knowledge in serial communication interfaces RS232/485 (protocols Modbus RTU, Profibus), Ethernet

Experienced in performing preventative/corrective maintenance in a manufacturing, engineering and laboratory environment

Experienced in troubleshooting to component level process control systems and instruments. Strong practical hands-on electrical & electronic aptitude

Skilled in prototyping electronic circuits and assembly PCB (printed circuit boards) using good soldering skills in SMD components. Repair, design and modifying PCB

Skilled in reading schematics, electrical diagrams, wiring diagrams, mechanical drawings, bill of materials

Familiar with engineering standards ISA, IEEE, NAMUR, ASMI, ANSI, NEMA, IEC

Experienced in using oscilloscopes, multimeters, signal generators, calibrators, power supplies and other electronic lab equipment

Familiar with 3 phase AC motors, pneumatic controllers and instrumentation

Familiar with instruments Honeywell, Yokogawa, ABB, Phoenix Contact, Schneider Electric, Siemens, Weidmuller, Emerson Rosemount, Endress & Hauser, Metrix, ElkoEp, Optex.

Ability to work independently with minimal supervision

IT SKILLS:

Expert in MS Office (Word, Excel, MS Visio), CorelDRAW, AutoCAD Electrical to produce wiring instructions, operational sequences, bill of materials, electrical and functional diagrams, and project related support documentation

Use Adobe InDesign and QuarkXPress to create operating manuals and product datasheets

Experienced in Mathcad for schematic and metrology calculations

Experienced in Altium, PCAD, NI Multisim for schematic capture and PCB design

Familiar with Ladder Diagram for PLC programming

Able to install and configure PC operating systems Windows XP, 7, 10

WORK EXPERIENCE:

THERMOPLASTIC SHEETS MANUFACTURE, Charlotte, NC, USA

02/2015 – Present

PROCESS TECHNICIAN & ELECTRICAL INSTRUMENTATION TECHNICIAN

Troubleshooting and maintenance temperature control systems, electrical and water heating system, power control electrical unit, light transmitter and cutting units, motion control electrical unit, pneumatic controllers and instrumentation (Phoenix Contact, Siemens, ABB, Festo)

Calibration light transmitter and pressure panel meters (LTlutron, Autonics)

MARANTA ELECTRO, Kiev, Ukraine

05/2009 – 12/2014

ELECTRONICS & INSTRUMENTATION DESIGN ENGINEER

Design schematic diagrams and PCB design analog signal conditioners, A/D I/O interface PLC modules

Design and integration multifunctional relay control systems, temperature and level process control systems for commercial, industrial, and domestic purposes (Omron, Autonics, Phoenix Contact, Schneider Electric, ElkoEp, Optex)

Troubleshooting to component level analog signal conditioners, analog and digital I/O interface modules

PROMSAT, Kiev, Ukraine

01/2003 – 03/2009

ELECTRICAL & INSTRUMENTATION ENGINEER

Design, installation, integration multifunctional relay control systems, temperature and level process control systems, vibration monitoring machinery protection industrial control systems (Schneider Electric, Omron, Autonics, ABB, Weidmuller, Emerson Rosemount, Endress & Hauser, Metrix)

Updating ladder diagrams for PLC, updating I/O configurations, hardware troubleshooting

Development electrical diagrams, wiring diagrams, specifications, operating manuals

SATURN DATA INTERNATIONAL, Kiev, Ukraine

03/1998 – 12/2002

ELECTRONICS ENGINEER

Design schematic diagrams and PCB design analog signal conditioners, temperature transmitters and indicators

Prototyping electronic circuits and assembly PCB. Repair, design and modifying PCB

Contact this candidate