Neftali O. Rodriguez

***** ********** *****, ***** ***, AL 36541 Phone: 251-***-**** email: acvpvj@r.postjobfree.com

Objective: To further develop my abilities and become a valued asset with a growing company.

Experience:

January 2016-May 2016 Merit Electric Company ORMAT Compressor Station, Gunlock, Utah

Built a geothermal power plant, installed cable tray, rigid and emt conduit, pulled wire devices to panel boxes inside mcc, terminated low voltage on instrumentation devices, installation of exterior lights, 277 VAC, installed heat trace wires on devices.

August 2015-December 2015 CF Industries Sergeant Bluff, Iowa

Installed cable tray, junction boxes, transmitter devices, lighting Petrochemical, running conduit termination on different circuits at compressor house

June 2015-July 2015 Metahnex Petrochemical Plant Geosmar, Louisiana

Installed cable tray, 5kv wire pulling, control wire pulling, duct bank, rigid conduit, man lift operation, grounding, and termination.

January 2015-May 2015 Devon Gas and Oil Pipelines, MMR Contractors Riverton, Wyoming

•Electrician in charge of fabrication, instrumentation, installing RIO Panels, MCC room, placed and pulled cables for circuits.

August 2014-December 2014 Haskell Gloster, Mississippi

•Draxbiomas: Electrician installing 3ph 480v motors for conveyors;

•Furnace plant installing hydraulic motors, general 277v lights, terminations in the MCC room and troubleshoot controls;

•Placed and pulled insulated wires or cables through the conduit to complete the circuits.

June 2014-August 2014 Mereling Vancouver to Western Alaska

•Electrician on cruise ship Disney Wonder

•Installed new LED lighting around swimming pool, outside stairways;

•Replaced interior lights in restaurant;

•Installed panels, cables, and alarms.

February 2014 – May 2014 Offshore Inland Campeche, Mexico

•Electrical contractor in rig TODCO for ORO NEGRO

•Rebuild the whole accommodations installed all fire alarms and gaitronics;

•Installing e-lights, terminate the draw works power and controls in the derrick.

November 2013 - February 2014 Maersk Developer

•Thruster Room: Disconnect sensors and removed eight thrusters to be sent to overhauling;

•De-term all exhaust-intake motor fans throughout rig. Re-term them back after replacing all batteries and emergency lights, replaced sensors (load, proximity, temperature, etc.) throughout the rig;

•Replaced MCTS with new roxter blocks;

•Installed a new disconnect panel and ran cables to main switch board from the mud room.

2011-November 2013 Offshore Inland

•Working as electrical contractor in Transocean oil rig, Henry Goodrich; Navigator, Noble; Technip Global 1200; TODCO 3 (Pemex); Halliburton, Mexico; ISO, Mexico; Demadrill, Mexico; Carnival Triumph, Seadrill (West Auriga) drill boat; Embridge, Gulf of Mexico.

•Performed heavy power hook-up load centers switchboards

•Performed layouts, hook-ups and cable terminations.

•Installed junction boxes, receptacles, lighting fixtures, power panels, motor control center mcc, valves, cable wire ways and transformers

•Reads Marine Blue prints, repair and troubleshooting electrical equipment.

2010 Tradesman International Fort Bening, GA

•Commercial job installing fire alarms, heat sensor smoke detectors, lighting receptacles, and ceiling fans at Heros and Veterans Hospital.

2009-2010 ThyssenKrupp USA Mobile, Alabama

Industrial Electrician

•Performed industrial electric work manufacturing cable trays/wire ways

•Completing whole line, thousands of linear footage on heavy duty cables.

•Installation of equipment; 35kv transformers, high voltage motors,

•Performed terminations on power panels, motors, signal and MCPc’s panels.

•Performed electrical terminations on PCR’s .detecting troubleshooting in

•Signal and controls panels, also performed installing rigid pipes from 3/4 inch

•Up to 3 inches diameter, thousands of linear footage.

2008-2009 Austal USA Ship Mobile, Alabama

First Class Electrician

•Marine Electrician performing electrical installations on US Navy ships.

•Performed layouts, hook ups and cable terminations, wire ways installations.

•Worked on three motor circuits, heavy power hook-up, switchboards, power panels, vital distributions panels, motor control centers, JP5 pumps, lighting panels, motors & other local hook-ups

•Installed junction boxes. Repaired and troubleshoot of electrical equipment

•Has experience with Marine Blueprints and schematics.

2006-2008 Northrop Grumman Pascagoula, Mississippi

1st Class Marine Electrician

•Performed, marine electrical work, at mcc’s, vfd’s, high power single or 3 phase disconnects, switchboard, motors and transformers, capacitors and starters.

•Termination and diagnostic of: lighting circuits, and breakers, responsible for all lighting and sound systems.

Additional Information

Bilingual, English and Spanish

Hard worker and dependable

OSHA certified (30 hrs. safety training)

OSHA Marine (10 hrs. safety training)

HUET Certification

MAERSK DRILLING Certificate of Training

TWIC Card

GOM LICENSE TO GO OFFSHORE; VALID PASSPORT

Adult First Aid, CPR/AED

PEC SafeGulf Card

Level I Antiterrorism Awareness Training

Contact this candidate