High School Power

QUANG NGUYEN

***** ********** **, *** ***, Houston, TX 77075 H: 832-***-****

***********@*****.***

SUMMARY

I would like to obtain mechanical asembler position in a grounded

companywhere i can apply my wide range of knowledge and experience to

the growth of the companyand move up my career and be successfull.

Authorized to work in the US for any employer

SKILLS

Have the quickness and knowledge Reading Comprehension

to be able to learn and work well Troubleshooting

with others, observe and Critical Thinking

demonstrate Mathematics

Observe and demonstrate and Operation and Control

perform well to finish tasks early Installation

Mechanical (5 years), Assembler (5

years), electrician (3 years)

Production and Processing

Quality Control Analysis

Education and Training

EXPERIENCE

01/2016-06/2016

Electrician installer

TAS Energy

Install busway and maintenance, align the edges of the joint stack with the edges of the housing end ramps

Center the joint stack between the joint supports.

Strip, cut, terminate wires according to prints

Install junction boxes, fuses, devices according to prints.

Set Torque and tighten all bolts to meet customer requirements standards.

Operate bandsaw, cutting, drilling, tapping holes to run pipes and wires to the joints.

Pull wires from point A to point B and terminate.

Mechanical Assembler 05/2013 - 01/2016

Toshiba International Corps - Houston, TX

Assemble parts and units, position, align and install, cabling, wiring and

operating hand tools.

Connect cables, tubes and wiring according to prints.

identify mistakes and correct issues and address issues to leadman or

supervisor for further notice.

Be able to work and finished units from 445 hp, 600hp, 800 hp, and 1200hp

units in 8 months projects done.

Inspect, test, and adjust completed units to ensure that units meet

specifications, tolerances, and customer order requirements.

Drill, tap, ream, countersink, and spot-face bolt holes in parts, using drill

presses and portable power drills.

File, lap, and buff parts to fit, using hand and power tools.

Operate small cranes to transport or position large parts.

Operate or tend automated assembling equipment, such as hand tools, power

tools and machines.

Assembly Technician 04/2010 - 02/2013

DXP Enterprises - Houston, TX

Perform quality checks on products and parts.

Read designed drawings and engineering prints.

Assemble parts, level and measure skits to set on even height and length.

Operate hand tools, power tools related to work.

Drilling and tap holes and sawing, cutting, filing to adjust parts fit properly.

Tightened bolts and set torque assigned to size of bolts, apply check after

finished to assure final work.

Review work orders and blueprints to ensure work is performed according to

specifications.

Rotate through all the tasks required in a particular production process.

Maintain production equipment and machinery.

Provide assistance in the production of wiring assemblies.

Shovel, sweep, or otherwise clean work areas.

Electrician Assembler 12/2007 - 03/2010

Powell - Houston, TX

Inspect, test, and adjust completed units to ensure that units meet

specifications, tolerances, and customer order requirements.

Assemble parts or units, and position, align, and fasten units to assemblies,

subassemblies, or frames.

Using hand tools and power tools, operate cranes to lift components such as

VFD, CPT, or wiring panel to mount to the unit.

Position, align, and adjust parts for proper fit and assembly.

Connect cables, tubes, and wiring, according to specifications.

Attach name plates and mark identifying information on parts.

Read blueprints and specifications to determine component parts and

assembly sequences of electromechanical units.

Disassemble units to replace parts or to crate them for shipping.

Drill, tap, ream, countersink, and spot-face bolt holes in parts, using drill

presses and portable power drills.

Ability and knowledge to address and report issues to lead man or supervisor

to execute problems.

Work well with co workers, provide training and practices to new employee.

Ability to learn and working in any lines

EDUCATION

Electrician certificate: Electrical Aug 2013

Gary job Corps - San Marcos, TX

Associate degree: business and marketing Jul 2013

University of Phoenix - Houston, TX

High School Diploma: high school studies Jun 2009

United Christian High School - Houston, TX

Contact this candidate