Electrical Engineering Power

CHANDAN DIGAMBAR PARDHI

Vellore Institute of Technology (VIT) University

Address: L-502, Dwarka Suncrest Society Phase-3,

Pimple Saudagar, Pune-411027, Maharashtra.

Contact No: 967-***-**** Email: *******.******@*****.*** OBJECTIVE

To gain a dynamic and challenging role in the organization that will offer me the best opportunity for further development of my abilities, skills and knowledge in established firm with long term career growth. EDUCATION

Program Institution %/CGPA

Year of

completion

M Tech in Power

Electronics and Drives

Vellore Institute of Technology, Vellore

(VIT University)

8.71 2015

B Tech in Electrical

Engineering

Dr. Babasaheb Ambedkar Technological

University, Lonere

6.93 2011

XII Nevjabai Hitkarini College, Bramhapuri 77.17 2007 X Nevjabai Hitkarini High School, Bramhapuri 75.33 2005 SCHOLASTIC ACHIEVEMENTS

Published an IEEE paper in “ICCPEIC-2014”

Qualified in GATE 2013

All India VITMEE 2013 rank: 16

Won 3rd Prize in “NCECIS-2011” National Level paper presentation held at Loni COURSE WORK

Solid State AC Drives

Analysis of Converters

Solid State DC Drives

Control System

Basics of Analog and Digital Circuit Design

Analysis of Inverter

Network Analysis

Power Electronics applications in Power System

COMPUTATIONAL SKILL

MATLAB SIMULINK, ORCAD, PSIM, dSPACE, MS-OFFICE

TRAININGS ATTENDED

Participated in the pre-conference Tutorial in ICAEE’14, the 1st International Conference on Advance in Electrical Engineering organized by School of Electrical Engineering at VIT University, Vellore.

Participated in one day workshop on Overview of Variable Frequency Electrical Drives, Refrigeration and Air-Conditioning conducted by DANFOSS INDIA at VIT University Vellore.

Two week In-plant training at “MAHAGENCO Koradi Thermal Power Station, Nagpur.” during 15 June 2009 to 27 June 2009. Exposure to Thermal Power Plant. PROJECTS

M. Tech FINAL YEAR Project Title: DIRECT TORQUE CONTROL OF THREE PHASE INDUCTION MOTOR FED BY THREE LEVEL NPC INVERTER BASED ON FUZZY LOGIC. Vector control is the modern technique for the speed control of induction motor. The direct torque control

(DTC) of induction motor has good dynamic performance of torque and flux control. The switching frequency is variable and difficult to control due to hysteresis controllers. To overcome these problems Fuzzy controller is used to reduce torque and flux ripples which will improve the dynamic performance of machine. State Vector Pulse Width Modulation (SVPWM) method is an advanced, computation-intensive PWM method and possibly the best among all the PWM techniques for variable frequency drive application.

M. Tech FIRST YEAR Project Title: NON IDEAL BOOST INVERTER USING SLIDING-PI CONTROLLER FOR LOW POWER APPLICATIONS.

The Boost inverter is used to convert low DC voltage into sinusoidal AC output voltage. Sliding PI controller is used to reduce harmonics of output AC voltage. As single stage of conversion is used so the switching loses will also reduce. The Sliding-PI controller is the combinations of both Sliding mode controller and Proportional Integral controller. It will reduce the Total Harmonics Distortion of inverter output voltage and current which leads to reduction in heat generated in output connected devices.

B. Tech Project Title: SLIP POWER RECOVERY SYSTEM. Project site: Rashtriya Chemicals & Fertilizer Limited, Chembur The Ball mill is used in Phosphoric acid plant at RCF to crush the phosphorous rocks which is driven by Slip Ring Induction Motor. In the slips of that motor lots of power is wasted. So in order to conserve the electricity we studied the slip power recovery techniques. A case study has been done in Machine Laboratory at Gangotri Sankul in this regard.

CO-CURRICULAR ACTIVITIES

Published an IEEE paper in “ICCPEIC -2014” International Conference on 17 April 2014

Presented a paper in 8th International Conference on Science, Engineering and Technology (SET)

Presented a paper in 7th International Conference on Science, Engineering and Technology (SET)

Presented a paper in National Level paper presentation at “CHEMFRATERNITY-2011”

Presented a paper in National Level paper presentation at “CYNOCURE-2011”

Qualified for final round of “SWITH-CRAFT” at “CYNOCURE-2011”

Executive Member of “Electrical Engineering Student Association” in 2009-2010

Completed “B” Certification in NCC with A grade

Won several prizes in extra-curricular activities in school and college PERSONAL DETAILS

Date of birth: 30th November 1989

Nationality: Indian

Gender: Male

Hobbies: Playing Cricket, listening songs

Languages known: English, Hindi, Marathi

Contact this candidate