Nace Certified Painting/ Coating Inspctor-Level 2

Contact Address Tel. No: 080********, 081********

#** ******* ***.******** *********** E-mail ****************@*****.***

Rivers State, Nigeria . ******.*****@*****.***

NNEJI NNAMDI. O

OBJECTIVE

To optimize my skills, working assiduously towards achieving the goals set by my company

or organization, absolute loyalty with genuine collaboration effort to ensure high productivity and

efficient delivery.

PERSONAL PROFILE

A Graduate of Industrial PHYSICS. Experienced in Different working Fields with Over 10 Years

Inspection work experience in various kinds of coatings; Linings; Fireproofing;Water jetting;

Insulation; Pickling and passivation; Thermal Sprays; Hot-Dip Galvanizing; and other forms of

Metalizing;; pipeline coatings; FBE coating,3LPP,Oil Storage Tanks, Barges, Bridges, Pipelines and any

form of structural steel.

AREAS OF EXPERIENCE

Painting,Coating,Evaluation,(NACE Coating Inspector Level II- Certified)Hands on All Major Producing

Companies in Nigeria .General Coating & Painting Specifications

A versatile and competent Protective Coating Inspector with reliable approach to all tasks and

excellent team player who is interested in new challenges in the oil and gas industry as related to

corrosion.Enforcement and verification of work performed in accordance with specification,

manufacturer recommendations and approved applicator coating procedure.

Assist the coating superintendent in all activities and responsible for technical and inspection works

for blasting &painting of structural,spools, tanks, piping and pipeline tie-in spools,platforms,pipe

supports,process pipe & vessel insulation and other miscellaneous protective coating work.

Coordinate along with client and assigned QC Inspectors & crew supervisor based on the daily

painting activities requirements, failure analysis and corrosion survey on old and existing platforms.

Conducting QC tests as related to coating and lining activities to ensure job compliance to

specifications

Strictly comply with company health,safety and environmental policy, procedures,regulations and

objectives as they relate to my area of responsibility, and ensure that they are effectively

implemented

Ensure all activities of blasting, painting, Insulation and Concrete lining activities as per the

requirements of approved construction drawing, procedure, manufacturer recommendation and

client specification.

Reviewing and monitoring on receipt and handling of the Blast abrasive & Paints materials, Insulation

materials, Coating & wrapping materials,to check the product designation,batch number,and shelf life

including MSDS &PDS of manufacturer and color codes.

Career Summary:

COMPANY: AMBER RESOURCES NIGERIA LIMITED

CLIENTS: CHEVRON, TOTAL, MOBIL, SNEPCO, ADDAX, NLNG,SEPTA,SAIPEM,GLOBSTAR, EFAG,

PONTICELLI, etc

POSITION: Painting & Coating Engineer

DURATION: MARCH. 2011 till date

Roles & Responsibilities:

Engineering support throughout all coating and painting phases of a project.

Timely completion of coating engineering deliverables within man-hour budget.

Ensuring that technical preparations result in cost and time efficient project execution in accordance with contractual, regulatory, and commercial requirements.

Preparation of painting and coating consumables MTO, MR.

Selection of coating materials/consumables in line with company specifications.

Review and comment on subcontractor technical tender proposals.

Technical liaison with Procurement, QA/QC, HSE, and Subcontractors.

Coordinating with Subcontractors regarding PQTs / PPT and other testing requirements. E.G Application of High Density Polyurethane Foam (HDPUF) on the Field Joint Coating to Subsea pipeline.

Preparation of Technical Queries and other deviations.

Authorized to perform technical communication with subcontractors.

Conduct effective monitoring programs on coatings of existing equipment, structures and facilities to access conditions and identify problems

Prepares adequate coating repair programs.

Participates in plant corrosion inspections during shutdowns and investigates failures to identify causes. Highlights areas of concern and advises on improvements required.

Liaises with inspection unit and other concerned parties to coordinates activities on corrosion mitigation and control matters.

Comply with company health, safety and environmental policy, procedures, regulations and objectives as they relate to my area of responsibility, and ensure that they are effectively implemented.

CLIENT SNEPCO AUG.2014-TILL DATE

DEPARTMENT QA/QC

PROJECT RL RISERS/ TEST-TANK BLASTING /PAINTING.

POSITION COATING/PAINTING INSPECTOR.

DUTIES/RESPONSIBILITEIS-

Identification of defects and repair methods.

Checking Coating Materials at the Job site prior to the initiation of the job for conformance to spec.

Audit coating mixing

Inspection of painting equipment to see that it is in good conditioned meets project specification for material to be applied

Surfaces blasted inspected to ensure that they meet specification prior to any coating application

Monitoring environmental condition for appropriate / allowable coating application

Proper check of application equipment to ensure normal pressures used for the materials specified

Materials sequence specifications are being followed

Determination of wet / dry film thickness of each coat

Audit cleanliness between coats

Maintaining cure or drying time to ensure that specification are followed

Approve or disapprove all coating surfaces not meeting specification

Adhesion testing e.g. Cross hatch test, pull off test etc

CLIENT TOTAL & MOBIL MAY2014 – AUG.2014

DEPARTMENT QA/QC

PROJECT OML 99 (AMENAM/KPONO) SECTIONAL REPLACEMENT OF 16'' HP

CRUDEEXPORT LINE AT AMD1/D2& DECK EXTENSION BLASTING/PAINTING

POSITION COATING/PAINTING INSPECTOR.

DUTIES/RESPONSIBILITEIS

Carry out general QA/QC task to ensure all activities involved in coating process

is done as per the project specification.

Ensure that equipment,material,paints and condition of work were all certified

ok before during and after the job.

Take records/document all reports before commencing, during and after the job

for traceability purposes.

CLEINT NLNG BONNY. OCT.2013-APRIL2014

DEPARTMENT: QAQC

PROJECT: TRAIN 2 SHUTDOWN BLASTING/PAINTING & FACILITY

MAINTENANCE

POSITION: QC INSULATION/PAINTING INSPECTOR

DUTIES/RESPONSIBILITEIS:-

Carry out general QC task to ensure all activities are done as per the project spec.

Inspect location and suitability of access for areas of work, type of blasting equipment

and tools to be used, coating material storage conditions, type of coating materials

to be used, type and size of blasting media, metal surface imperfections/defects.

pre-cleaning or solvent cleaning of surface, degree of cleanliness required, surface

profile of blast cleaned surface, type of coating application equipment

and tools, Passivation/acid cleaning of Stainless steel.

Coordination of activities on various site and personnel

Perform other tests-profile, adhesion, blotter, sieve, holiday tests respectively

Progressively documented.

CLIENT TOTAL JAN.2013-SEPT 3013

DEPARTMENT: QA/QC

PROJECT: INTERNAL BLASTING OF PIPES/OILING AND PAINTING

POSITION: QC INSPECTOR.

DUTIES/RESPONSIBILITEIS;

Coordinate and carry out inspections before, during and after each task to

make sure that the (work) are done according to the project specification.

Record and maintain each pipe tractability-(serial,lot,part and heat treatment numbers).

Ensure all equipment to be used on site is properly calibrated and has valid certs.

Daily ambient condition check before,during and after work

Organize and maintain proper handling of blasted/oiled and painted pipes.

Daily record/progress reports.

Reviewing of painting procedures/inspection test plan (ITP).

Etc.

CLIENT: EXXON MOBIL. FEB.2012 – JULY 2012.

PROJECT FABRICATION, BLASTING/PAINTING OF PIG LAUNCHERS/RECIEVERS FOR EXXON

DEPARTMENT: QA/QC

POSITION: PAINTING/COATING INSPECTOR.

DUTIES/RESPONSIBILITIES;-

Carry out general QA/QC task to ensure all activities done as per project spec.

Conducting QC tests as related to coating activities to ensure job compliance to specifications

Ensure all activities of blasting, painting, are as per the requirements of approved construction drawing, procedure, manufacturer recommendation and client specification

Reviewing/monitoring on receipt and handling of the Blast abrasive & Paints materials,Coating &wrapping materials, to check the product designation, batch number, and shelf life including MSDS & PDS of manufacturer and color codes(Ral).

CLIENT: SEPTA ENERGY NIG LTD AUG.2012-DEC.2012

PROJECT BLASTING AND PAINTING OF UQUO GAS PROCESSING FACILITY

(-PIPES, FLANGES, ELBOWS, CONECTORS/ CON.REDUCERS)

DEPARTMENT: QAQC

POSITION: PAINTING/COATING INSPECTOR.

DUTIES/RESPONSIBILITIES:

Pipe identification (schedule chart),elbows, fittings/Ambient condition check

Job evaluation and records keeping.

Reviewing of painting procedures/inspection test plan (ITP).

Carry out the normal QA/QC daily activity according to specification

Conducting destructive and non destructive tests on surfaces to check coating Adhesion/DFT.

Identification of defects on painted or metal surface and initiating repair procedures.

CLIENT: TOTAL (TEPNL-USAN PROJECT) MARCH 2011-JAN.2012

PROJECT: OML 58 UPGRADE PROJECT PHASE 1. Blasting and painting, PIPES, SUPPORTS

DEPARTMENT: QAQC

POSITION: PAINTING/COATING INSPECTOR.

DUTIES/RESPONSIBILITEIS:-.

Carry out general QA/QC task to ensure all activities involved in coating process is done

as per the project specification.

Ensure all equipment to be used on site is properly calibrated and has valid certification.

Perform other tests-profile, adhesion, blotter, sieve, holiday tests (but a few) respectively.

COMPANY: OPANIL Nigeria Limited JAN.2008-JAN. 2011

CLIENT: CHEVRON Nigeria Limited

PROJECT A: Mobile maintenance Painting, North Offshore Production

Platform, MEREN, EWAN/MEREN WIP

PROJECT B: Maintenance painting project of BOP Offshore Terminal Product

Platform.

POSITION: Coating Inspector

Duties and responsibilities

Carried out inspection on blasting and painting equipment prior to the commencement of job.Eg.ASTM D 4285 – Standard test method for indication oil or water compressed air.

Inspection on paint materials to verify shelf life, and storage condition in accordance to the project spec. and manufacturer product data sheet.

Conducts ambient temperature checks e.g. relative humidity, dew point, surface temp, and air temps.

Pre-treatment inspection in order to degrease and use an approved solvent for cleaning areas

Inspection of blasted surface to check for soluble salt contamination less than 30mg/m2 (ISO 8502-3)

Verification of surface profile by using testex tape, visual comparator prior to painting. ISO 8501-1 to 3

Inspection of power tools profile prior to painting to avoid burnishing and to aid adhesion in conjunction project specification e.g. SSPC –SP 11.

Inspection of blast nozzles by nozzle orifice gauge to detect and discard worn nozzles.

Abrasives inspection e.g. Vial test

WFT and DFT inspection ( SSPC-PA2),Inspection of stripe coated area prior to application of full coat.

Inspection of inorganic zinc silicate application to check for curing by MEK rub test prior the application of any subsequent coat in accordance with ASTM D4752

Adhesion test according to ASTM D 4541

Condition assessment of facilities & daily, weekly and monthly reports

Monitoring and recording of material usage throughout the phase of project duration.

COMPANY: ADAMAC PIPE COATING SERVICES LTD JAN 2007-SEPT2007

CLIENT SHELL

PROJECT: 3LPP / CWC /2LPE COATING.

DEPARTMENT: QAQC

POSITION: PAINTING / COATING INSPECTOR (ONSHORE/OFFSHORE).

DUTIES/RESPONSIBILITEIS:

Interpreting Clients Specifications and Liaising with Paint Manufactures to know if

the suitable products are as per the Specs. Review/Management of the approved

Purchase Orders and Related Invoices regarding Coating materials.

Comply and implement quality system requirements. Ensure fulfillment of all inspection

and test requirements at all stage as per Quality Control plan and contract requirements

and maintain pertinent records. Ensure that copies of applicable QC Plans are available

at the locations of work. Issue NCR when non conformance observed

during inspection/verification. Liaise with the Project Manager for the corrective action

against non conformances.

MEMBERSHIP:

Nigerian Society of Engineers (NSE), Graduate Member

Skill acquisition and job ethics

Energy conversion and power generation

Management principles and techniques

STRENGTH AND SKILLS:

Good management ability, enjoy working under pressure

Good team member, computer literate –Microsoft Word, Excel,

Good communication skill at all level, uphold truth integrity and faithfulness.

HOBBIES: Football, reading and composing songs.

PROFESSIONAL QUALIFICATION:

BOSIET 2014.

NATIONAL ASSOCIATION OF CORROSION ENGINEERS (UAE CHAPTER) 2011

HSE Professional (Health, Safety and Environment

Certified by SPDC and Nigerian Institute of Safety Professional (NISP) 2009

European Union Certified experts on needs assessment/NGO .

Field Data Manager (NOVASYS Nigeria Ltd Asaba) 2004

EDUCATION AND QUALIFICATION:

Federal University of Technology Owerri –Bachelor of Technology

(B.Tech. Hons. in Industrial Physics). 2006

Mbaise Sec. School Aboh Mbaise –SSCE Certificate. 1996

Central School Oboama – First School Leaving Certificate 1990.

BIO-DATA:

Sex: Male

Marital: Married

State of Origin : Imo

Nationality: Nigeria

REFEREES:. On request

Contact this candidate