Hamada fawzy Mahmoud abd_elmegied

Main address: eledwa, elfayoum, Egypt.

Mobile : +966********* .

E-Mail : acuqsn@r.postjobfree.com

POSITION: lead I&C Engineer

OBJECTIVE

EDUCATION

WORK

EXPERIENCE

Seeking a career with a progressive organization where I can utilize my skills, knowledge and experience in instrument and control engineering major in a challenging role that allows for advancement and growth.

• Cairo university _ elfayoum branch -- Faculty of Engineering BS.C in Electrical Engineering 2005.

• Electronics & Electrical Communications Department.

• Cumulative Grade: GOOD (69.75 %.)

• Graduation project: CDMA WITH STEGANOGRAPHY

• Grade project : “Excellent “

Feb.2016 till now:

Company:

Altoukhi for industrial trading and contracting KSA. Conversion of hail -2 simple cycle to combined cycle power plant 170 MW has

4 HRSG Amec Foster Wheeler,

STG Siemens,

ACC ( air cooling condenser) SPX,

Water treatment

Power plant controlled by Siemens DCS.

Title : Lead I&C ENGINEER .

Job description:

Installation all field instrumentation for HRSG, STG, ACC, WT. Installation DCS system for Siemens.

Test and commissioning for all instrument and control system. Feb.2015 till Feb 2016:

Company:

Saudi services for electro mechanic work Co. (S.S.E.M) KSA. Rafha power plant – II extension I project

GTG Siemens frame SGT6 - 2000E - control system SPPA-T3000 Power plant controlled by Emerson DCS.

Title : Senior I&C construction and commissioning engineer Job description:

Installation all field instrumentation for GTG ( vibration, speed sensor, thermocouple and key pharos )

Installation DCS system for Emerson

Test and commissioning for all instrument and control system Installation and testing for MINIMAX AND NOTIFIRE fire alarm system Dec.2013 till July 2014:

Company :

Samsung C&T Qurayyah independent power project ( qipp-KSA)

• 12 SIEMENS GAS TURBINE ( 230 MW) TYPE NO : SGT6-5000F

• 12 HRSG

• 6 SIEMENS STEAM TURBINE

• Siemens control system HMI SPPA T3000( Siemens power plant automation )

Title: I&C Commissioning engineer.

Job description:

• Working on Siemens gas turbine control system (PLC S7-400)

• Loop Check, line check for All Field Instruments

• Calibrate the instrument for all turbine auxiliary systems

(EH control system- lube oil- fuel gas system- fuel oil system- water injection )

• Trouble Shooting & Maintenance Software and Hardware February 2007 till Dec 2013:

• Company: Electrical Authority North Upper Egypt Zone

(EL Kurimat 2 x 650 MW power plant) EGYPT.

• 2 GE Steam Turbines, 650 MW. Control system is MARK V HMI.

• 2 Conventional Boilers, 36 Burners (BABCOCK WELCOX – Canada).

• Water treatment plant (BAMAG) Control system is PLC GE FANUC.

• The plant is controlled via WESTINGHOUSE DCS control system.

• Auxiliary system controlled by Allen Bradley PLC 5, SLC 500 Title: Instrumentation and Control Engineer.

Job Description:

• Working on GE turbine control system (MKV speed tronic) for large steam Turbines (2* 650 MW) in the field of loop checking the system and maintenance Of field instruments related to turbine control system.

• Calibrating all kinds of field instruments connected to turbine different systems.

• Adjustment and check turbine vibration detectors and make configuration for turbine supervisory instrument (Bentley Nevada system).

• Analysing and troubleshooting the problems related to hardware or Software for control systems.

• Working on Allen Bradley PLC for turbine Bypass system

• Maintenance engineer in GE auxiliary system for turbine instruments Calibration and Maintenance and install new part for Following systems: Lube oil system -- Hydraulic system (EHC)

H2 seal oil system -- Bypass system

• Preparing the required spare parts list and preventive maintenance schedules.

Working from Dec. 2009 to Apr. 2010

• on overall outage for GE LST to maintain turbine aux. system in good condition

• Upgrade MKV system from <I> to <HMI> by change MKV EEPROM TRAINING

and software in order to use simplicity software under WINXP.

• Working on BFPT as I&C maintenance engineer for both turbine and pump.

Working from 1st Dec 2011 to 1st mar 2012

• Perform the overhaul outage for steam turbine unit( No. 2) as follows :

Dismount all the turbine supervisory instrument and calibrate vibration probes using GE test kit.

Install turbine supervisor instruments and adjust the offset for: Differential expansion, wear detector for thrust bearing, eccentricity, speed sensor, rotor expansion and key phasor.

Calibrate the instrument for all turbine auxiliary systems

Upgrade turbine control system (MKV) from< I > TO <HMI> for unit NO. 2 working as a maintenance engineer in the following fields: Air Compressors (PLC Controller)

Checking, Testing Logic Circuits (Using Allen Bradley PLC 5, SLC 500)

Trouble Shooting & Maintenance Software and Hardware

Calibration All Field Instruments for Air Compressors Water treatment Plant and waste water

Loop Check, Calibration, Maintenance for All Field Instruments Water Treatment and Polishing System Using (GE Fanuc LM 90-70)

Check All Control Circuits for Water treatment Through control loops and ladders

Calibration for Water treatment For

Pneumatic Control V/V (fisher and Bialy), Pneumatic On/Off v/v.

Transmitter (Flow, Level, Pressure, Temp)

Thermocouples, RTD Devices,

Switches (pressure, differential pressure and temp.) and Indicators

motorized Control valve (Auma,), Motorized valves (Limit torque)

• Diagnostic problem in PLC include (on line)This work include Upload, down load program from PLC and to PLC

• Distributed control system(DCS)[installation ; power supplies ; data highway ; Ethernet ; I/O cards Checking and troubleshooting from the filed up to the WDPF SYSTEM

• All boiler filed instruments test,calibration,loop checks & maintenance

• Maintenance engineer for FIRE ALARM System

(Water SYS / SPRINKLER SYS / pre- action sys /Foam sys/ FM 200 Sys)

• Working on EMPAC program (asset software) for work orders and spare parts.

July 2005 to June 2006

Company: Pharaoh's ceramics group.

Title: Instrumentation and control Engineer

• Plc. alenbradly

June 2006 to February 2007

Company: Kouta steel group.

Title: Instrumentation and control Engineer

• Plc. Siemens S7

18th-23rd January 2014

Advanced course in PLC SIEMENS S7-300 in elkurimat training centre.

2nd -4th march 2014

Advanced course in motorized valves (AUMA VALVES) matec &Tec this course covered the latest techniques of electric control of SKILLS

PERSONAL

INFORMATION

REFERENCE

mechanical application using the electric actuator technology. By Arabian telecontrol & engineering centre

March – April 2010

Advanced Course in Turbine Generator Control System

"ALSPA P320 TGC" V2+ with ALSTOM Power Generation Company, Mannheim, Germany.

Advanced Course in Turbine Generator Control System "ALSPA P320 TGC " V2+ and AVR Control System with ALSTOM Power System Company, Belfort, France

25th -29th October 2009

Advanced course in SCADA system by using RSVIEW32 software, Sahara group.

HMI MARK V TRAINING in field by GE.

• Language:

Arabic: Fluent (Native Language).

English: good (spoken and written).

Computer:

Word, Excel, PowerPoint, internet.

Date of birth: 14/11/1983.

Place of birth: Elfayoum- Egypt.

Military Status: Exempted

Marital Status: Married.

Driving license: 54248

Mr faheem khaliq

Power consultant I&C engineer

Mobil # : 054*******

Mr Mohamed kinawy

UPPEC I&C lead engineer

Mobile #: 002-0100 6571046

Contact this candidate