Engineer Electrical Engineering

TRUNG M. NGUYEN

616-***-**** (cell)

*************@*****.*** (email)

WORK EXPERIENCE

Atlas Copco Mafi-Trench Company LLC, Santa Maria, California (06/22/2009 – 04/19/2016) SENIOR INSTRUMENTATION & CONTROLS ENGINEER.

-Responsible for designing, developing TurboExpander (Lube Oil / Magnetic Bearing Cabinet) and Expander Generator Machine in the hazardous location per NEC and IEC.

-Using AutoCad to layout the junction boxes, cabinets, control diagrams, and networking.

-Oversee the shop to build all junction boxes, cabinets and skid instrumentations, junction boxes layout on the skid.

-Skid functional test to test all instrumentations (transmitters, RTD, flow meters, proximitors) and FAT (Factory Acceptance Test) for control cabinet using simulator panel; SAT (Site Acceptance Test)

-Working with mechanical engineer, machine engineer, purchaser, the shop and other staff to build the machine per customer requirements.

-Liaising with customers, vendors

-Working with project manager, principle engineer to build the machine within the cost and schedule.

-Providing advice and support to field service and aftermarket.

-NFPA 70E, IEC knowledge and experiment with area electrical classification including Class 1 Div 1, Zone 1. Exd, Exe, Ex ia/ib

-Safety Integrity Level (SIL 2)

HMI Touchscreen (Allen Bradley PanelView Plus 1250).

PLC:

Software: Allen Bradley ControlLogic Ver, 19, 20

Hardware: 1756-L62, 1756-L72 controller, 1794 Flex I/O

Network: Modbus TCP/IP protocal, Ethernet, Redundancy Ethernet

(1756-EN2TR), Fiber, Device-Level ring (DLR)

Allen Bradley PLC redundant controller

Seal Gas Heater (CCI Caloritech) with Seal Gas Heater Thyristor Control Panel with temperature controller (RTD/Transmitter)

Immersion Heater (Lube Oil Heater) (CCI Caloritech) with temperature control (RTD/Transmitter)

CCC (Compressor Controls Corporation) Vanguard Series 5

Motors (ABB IEC Explosive proof motor, ex, Baldor NEC / IEEE Std 841)

Level Transmitter/Level Indicator

Rosemount 8800 Vortex Flowmeter

Pepperl+Fuchs Bebco 3000 Series Type Z Purge (Pressurization System): to reduce the classification within the protected enclosure from Division 2 to Non-Hazardous Area.

Modcan32 (to simulate as a MODBUS Master device)

ModSim32 (to simulate as a MODBUS Slave device)

ProSoft Configuration Builder

Working knowledge of SAP

Redundant power supply

GE 3500 Bently Nevada Machinery Protection and Monitor Systems (Overspeed, Temperature, Vibration, Relay)

GE Bently Nevada 3701/55 Adapt Emergency Shutdown System (Overspeed detection)

Wonderware InTouch (HMI Machine Interface Software)

Armored / Unarmored Cable (NEC / IEC Cable), Cable Glands

Junction Boxes, Explosion Junction Boxes / Cabinet Layout, Customer Cabinet

Woodward 505E Digital Governor

Generator: Induction Generator (HIEC, ABB), Synchronous Generator (HIEC), NGR (Neutral Grounding Resistor)

Gearbox (Lufkin, BSH)

Generator Protection Panel

-Woodward DSLC (Digital Synchronizer and Load Control)

-GE SR489 Relay / GE G60 Relay

-Lockout Relay 86

Dematic Corp., Grand Rapids, Michigan (11/1999 – 02/2009)

CONTROLS ENGINEER. Design and oversee proper installation and operation (troubleshooting) of conveyor systems at supported facilities:

HMI Touchscreen (ICONICS Magelis, Panelmate).

PLC:

Modicon (Software: Prowork NxT, Concept, Unity Pro M340; Hardware: Momentum, Compact, Quantum; Network: Modbus, Modbus Plus, Ethernet, Fiber),

AB (Software: RSLogix 500; Hardware: Flex I/O)

Sq. D VFD (Altivar 31, 66, 71), AB VFD (1336)

Sq. D Lexium Servo, AB Servo (1391-DES)

Networking with TCP/IP protocols, hubs, switchs (Ethernet, Modbus Plus network)

AutoCAD 2000, 2008 Electrical.

Cummings Industrial Systems, Lansing, Michigan (11/1997 –11/1999)

ELECTRICAL CONTROLS DESIGNER. Responsible for development of structured programs, system design, machine testing and troubleshooting:

Symax (Symate PLUS from square-D)

Panelview, IDT Panelmate (3900 KP)

AB PLC (AI, 6200)

Micromatic Textron, Holland, Michigan (07/1995 –10/1997)

CONTROLS ENGINEER. Design machinery components in the automotive industries:

Read specifications and design machines according to JIC & NFPA standards

Design control panels

Design Operator Interface

Design PLC program & debug machines

Park Metal, Detroit, Michigan (06/1993 –07/1995)

ELECTRICAL ENGINEER. Quality control and design layouts by producing the following power distribution systems:

Bus Duct (medium & low voltage)

Medium-Voltage Systems (metal-clad switchgear, low profile sectionalizing switchgear, power factor correction system, automatic transfer system, paralleling switchgear)

Low-Voltage System (panel board, switchboard, metal-enclosed draw-out switchgear, automatic transfer system, paralleling switchgear)

Metal Enclosures

Motor Control Centers

National Sign & Signal Company, Battle Creek, Michigan (09/1992 – 04/1993)

SENIOR-PROJECT DESIGNER. Design and build a light meter for calibrating the light output of the illuminated, fiber optics signs (team-work)

Western Michigan University, Kalamazoo, Michigan (09/1989 – 04/1993)

STUDENT SUPERVISOR OF ELECTRICAL ENGINEERING LABORATORY. Direct and supervise 15 work-study students with lab procedures; Advise and design various projects for faculty members within the Electrical Engineering Department

Western Michigan University, Kalamazoo, Michigan (09/1992 – 12/1992)

FACULTY ASSISTANT DESIGNER. Assist a faculty member in the Electrical Engineering Department with his research in augmenting the hearing capabilities of individuals with hearing losses (team-work)

QUALIFICATIONS

Hydraulics, Pneumatics, Motion Controller

Programmable Logic Controller (Allen-Bradley PLC-5, SLC-500, RSLogic 500, A.I., Updoc AB-2, Taylor (Modicon Proworx Plus), Modsoft, Concept)

Wonderware Intouch 5.6, Mitsubishi Variable Frequency Drive (A200E-UL), Assembly, Softwin (Xycom 3100C), Panel view 900, Panelmate III, C++ programming, AutoCAD R2000, PanelBuilder 1400E, Servo Drive (Indramat)

Lotus 1-2-3, Microsoft Word, Xtree, Fortran, Pascal, Basic, Pspice, knowledge in electronics applications

EDUCATION

Western Michigan University, Kalamazoo, Michigan. Bachelor of Science in Electrical Engineering from an ABET Engineering program, with emphasis in digital controls. Minor in Mathematics. (April 1993)

Grand Valley State University, Allendale, Michigan. (Attended September 1984 - May 1987)

PERSONAL STRENGTHS

Self-motivated

Strong interpersonal skills

Able to perform duties in a team environment, as well as individual tasks

Able to carry out multiple deadlines and assignments under pressure

Contact this candidate